Full course · free on YouTube · 2 h 2 min

Electric vehicle basics masterclass: free, 2 hours

A recorded masterclass of about 2 hours presented by Vatsal Shah of Skill-Lync. It follows an experimental EV that Skill-Lync built from scratch, covering the mechanical design, motor and controller, battery pack and charging, then auxiliary systems and wiring.

31 chapters · published 21 Dec 2022 · 2,48,524 views as of 19 Nov 2026 · by Skill-Lync

Free. We ask for your name and phone once before it plays here · or watch on YouTube ↗

Who is this course for?

Mechanical, electrical and automobile students and early-career engineers who want a first, hands-on explanation of how an electric car works.

What will you learn?

  • Describe how micro, mild, full hybrid and pure electric vehicles differ and why an EV converts energy in one stage
  • Tell outrunner (hub) and inrunner motors apart and explain the role of Hall sensors and permanent magnets
  • Read a motor torque-speed curve against the vehicle load curve to find an operating point
  • Explain how a motor controller uses a gate driver, MOSFET switches and PWM to set motor voltage
  • Size a battery pack from cell voltage and capacity, with cells in series and parallel (20 kWh worked example)
  • Describe what a battery management system does and how CC-CV charging works

What does each part of the course cover?

11 sections, in watching order. Click a timestamp to jump the player there. Chapter titles are from the video description, lightly edited for spelling.

  1. 0:0012 min · 5 chapters

    Introduction, EV types and why EVs cost more today

    The presenter describes an EV as a battery-powered, motor-operated vehicle, explains why EV numbers are low (high cost, low production volume), outlines micro, mild, full hybrid and pure electric vehicles, and compares the single-stage electrical conversion with the three-stage conversion in a petrol or diesel engine.

    Chapters
    • 0:00Introduction: how an electric vehicle works and why it took so long
    • 5:27Why EV numbers are low: cost, low volumes and demand
    • 6:52Types of electric vehicles: micro, mild, full hybrid and pure electric
    • 8:15Fuel versus electricity: efficiency and running cost per kilometre
    • 10:12Overview of the masterclass and the Skill-Lync EV platform
  2. 12:0510 min · 1 chapter

    Building the Skill-Lync EV test vehicle

    A walk round the experimental EV Skill-Lync built from scratch: ladder frame chassis, worm-wheel steering with a pitman arm, McPherson front and leaf-spring rear suspension, and the build order from welding to a first trial. FEA in ANSYS and vehicle dynamics in MATLAB are mentioned.

    Chapters
    • 12:05Building the Skill-Lync EV: chassis, steering, suspension and testing
  3. 22:175 min · 2 chapters

    Powertrain layout, reduction gearbox and single-speed drive

    Covers rear-, front- and all-wheel drive, why power must be shared between axles, and the reduction gearbox with differential (transaxle). A dashboard demonstration then shows the vehicle reversing with a switch, because the motor can turn either way.

    Chapters
    • 22:17Powertrain architecture: drive layouts, reduction gearbox and differential
    • 25:03Single-speed transmission and reversing with the motor
  4. 27:4023 min · 3 chapters

    Types of motors and how they are built

    Compares outrunner (hub) and inrunner motors, then permanent magnet and non-permanent magnet types such as induction and switched reluctance. The motors are opened up: brushes and commutator in a small DC motor, and stator, rotor magnets and Hall sensors in hub and inrunner motors. Ends with cost, torque-to-weight and control complexity.

    Chapters
    • 27:40Types of EV motors: outrunner (hub) and inrunner, permanent magnet and non-permanent magnet
    • 33:45Construction and working of motors: brushed motor, hub motor, inrunner motor and Hall sensors
    • 48:33Choosing the best motor: cost, torque-to-weight and control complexity
  5. 51:056 min · 2 chapters

    Motor specifications and cooling

    Explains the specifications of the traction motor in the Skill-Lync EV: brushless DC with a 3 kW continuous rating, continuous versus peak power, and mechanical details such as dimensions, weight and shaft arrangement. Natural cooling with a shaft fan is described, plus forced-air and liquid cooling for high-power motors.

    Chapters
    • 51:05Motor specifications: voltage, current, continuous and peak power, mechanical data
    • 55:28Keeping the motor cool: natural, forced-air and liquid cooling
  6. 56:4425 min · 3 chapters

    Motor control: torque-speed curves, controller and inverter demos

    Matches the vehicle load (constant rolling resistance plus drag rising with speed squared) to the motor torque-speed curve to find the operating point. Then covers the motor controller, gate driver, pulse width modulation, speed and rotor-position feedback, a six-switch inverter, a 24-MOSFET controller, a sensorless drive and regenerative braking.

    Chapters
    • 56:44Controlling the motor: torque-speed curves, motor controller, gate driver and PWM
    • 1:10:01Electronic control systems: speed and rotor-position feedback, six-switch inverter
    • 1:14:35Motor controller demonstration: MOSFET inverter, sensorless drive and regenerative braking
  7. 1:21:5612 min · 5 chapters

    Batteries: chemistries, lithium-ion versus lead-acid, pack design

    Contrasts the energy stored in fuel and in a battery, lists the lead-acid, nickel metal hydride and lithium-ion options, and compares lithium-ion with lead-acid. Covers low and high voltage packs, then sizes a 20 kWh pack from 3.6 V, 5 Ah cells in series and parallel.

    Chapters
    • 1:21:56Sources of power: energy stored in fuel versus battery
    • 1:23:33Rechargeable batteries for EVs and lithium-ion chemistries
    • 1:25:00Lithium-ion versus lead-acid batteries
    • 1:26:58Battery pack classification: low voltage and high voltage packs
    • 1:29:02Construction of battery packs: cells in series and parallel, sizing a 20 kWh pack
  8. 1:34:003 min · 2 chapters

    Discharge curves, C-rate and battery pack specifications

    Reads a cell discharge curve, explains why capacity depends on discharge current and temperature, and defines C-rate with a 5 Ah cell. Pack specifications follow: voltage limits, ampere-hours, power, watt-hours and life cycle, with the figures of the Skill-Lync pack.

    Chapters
    • 1:34:00Discharge characteristics: discharge curve and C-rate
    • 1:35:41Battery pack specifications: voltage, capacity, power, energy and life cycle
  9. 1:36:369 min · 3 chapters

    Battery management system and charging an EV

    Explains why a battery needs a battery management system to monitor cell voltage, current and temperature and to disconnect the pack on a fault. A BMS board is opened up. Charging covers AC to DC conversion, constant-current then constant-voltage charging, onboard chargers, AC and DC fast charging.

    Chapters
    • 1:36:36Managing battery performance: why a battery management system is needed
    • 1:38:43Inside a battery management system module
    • 1:40:40Charging an EV: CC-CV charging, onboard charger, AC and DC fast charging
  10. 1:45:4813 min · 4 chapters

    Auxiliary systems, DC-DC converter, wiring harness and console

    Shows why lights, horn and dashboard run from a separate 12 V lead-acid battery fed by a DC-DC converter from the 60 V pack, and why high and low voltage are isolated. Then the wiring harness (power and control cables, routing, noise) and the driver's console with throttle interlocks.

    Chapters
    • 1:45:48Auxiliary systems: why they need a separate 12 V supply
    • 1:47:25Powering auxiliary systems: DC-DC converter, 12 V battery and isolation
    • 1:51:22Wiring harness: power cables, control cables and design considerations
    • 1:56:53Driver's console: dashboard wiring and throttle interlocks
  11. 1:58:314 min · 1 chapter

    Simulation versus real-world performance

    After a test drive, logged battery current from a clamp meter is compared with the simulation of the vehicle. They do not match exactly, and the presenter lists the parameters left out of the model: tyre pressure, actual rolling resistance and aerodynamic drag without a body.

    Chapters
    • 1:58:31Simulations versus real-world performance: comparing logged and simulated data

Is the EV Basics Masterclass course really free?

Yes. All 2 h 2 min of it is free on Skill-Lync's YouTube channel, with no payment. To watch it on this page with the chapter guide, leave your name and phone number once; you can also watch it directly on YouTube. It was published on 21 Dec 2022 and had 2,48,524 views as of 19 Nov 2026. This page adds the chapter guide, a study plan and what to learn next.

How long does the EV Basics Masterclass course take to finish?

The video runs 2 h 2 min across 31 chapters. At one hour a day that is about 3 days; plan roughly twice that if you practise each exercise as you go. The longest section is "Motor control: torque-speed curves, controller and inverter demos" (25 min), so give it its own days.

Does the free electric vehicle course come with a certificate?

The video description has a "claim your certificate" link, which now opens this page. To ask about a certificate for this course, leave your name and phone number in the form below and a Skill-Lync counsellor will call you back. The paid Skill-Lync courses linked here include a certificate along with mentor-reviewed projects.

What should I learn after this course?

The next step is EV Fundamentals (free lessons), then EV Fundamentals (₹40,000), then Post Graduate Program in Electric Vehicle Design & Development (₹2,75,000). The free course teaches the concepts; the paid Skill-Lync courses add graded projects, mentor feedback and, in the PG programs, placement support.

Do I need any software to follow this EV masterclass?

No software is needed to watch it. The video is a hardware walkthrough: motors, a controller and a BMS are opened up and demonstrated on the table and in the car. It mentions that Skill-Lync used ANSYS for chassis analysis and MATLAB for vehicle simulation, but you do not have to install them.

Does an electric car have gears?

The masterclass explains that the Skill-Lync EV uses a single-speed reduction gearbox with a differential, because the motor works across a wide speed range at different torques. Reverse is done by changing the direction of current through the motor, shown with a switch on the dashboard, so no reverse gear is needed.

How is a battery pack for an EV sized?

The video works through a 20 kWh example. With 5 Ah, 3.6 V cells, it uses 100 cells in series for about 360 V and 11 in parallel for about 55 Ah. Cells in series and parallel are multiplied, not added, so the pack has about 1,100 cells.

Last updated 19 Nov 2026 · Course length, chapters, views and dates from the YouTube video on 19 Nov 2026 · Grow by Skill-Lync: free lessons from every course

Finished the course?

Ask about the certificate or your next course.

Leave your name and phone number. A Skill-Lync counsellor calls you back within one working day about the certificate for EV Basics Masterclass and the course that fits where you want to work.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Free full course · Skill-Lync

Start watching

Free, no payment. Leave your name and phone once and the whole EV Basics Masterclass course plays here, with every free lesson on Grow. A Skill-Lync counsellor may call you about the certificate or your next course.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.