← Course overviewFree lesson 1 of 3 · lesson 1 of 17Next lesson →

Unlock all 17 lessons of Overview of 4G Networks and evolutions to 5GFull course ₹40,000 · paid

Price & syllabus
Free lesson · 28 min · no payment

LTE Frame Structure, Resource Blocks, Bearers and QoS

A free lesson from Skill-Lync's Overview of 4G Networks and evolutions to 5G course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “Week 1 Session 1”

What will you learn in this free Overview of 4G Networks and evolutions to 5G lesson?

The instructor covers the FDD and TDD radio frame, built from 10 subframes of 1 ms, and shows that one resource block has 84 resource elements with normal cyclic prefix. The lesson then explains default and dedicated bearers, GBR versus non-GBR, and the QCI table.

  • FDD and TDD frame, subframe and slot
  • Resource element and 84 element resource block
  • Default versus dedicated EPS bearers
  • QCI values for GBR and non-GBR services

What comes after lesson 1?

The next free lesson is lesson 2, “LTE Protocol Stacks and Logical, Transport and Physical Channels” (29 min). Later in Skill-Lync's Overview of 4G Networks and evolutions to 5G course (paid): lesson 4, Week 1 Session 4; lesson 5, Week 2 Session 1; lesson 6, Week 2 Session 2. The full course has 17 lessons (7 h 11 min of video); see the course overview or its price and syllabus.

Lesson transcript

Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.

Hi. In this course, Overview of 4G Networks and Evolutions to 5G. Week 1. Let's discuss the quick recap of the last session. So in the last session, we discussed about LTE frequencies, bands, and bandwidths, where we discussed about various FTD and TDD bands. We saw a few examples. We saw the range of the frequencies of various bands, and also we saw that what all bands are supported as part of FDD, and what all bands are supported as part of TDD. Then we discussed about LTE supported bandwidths, where we discussed about various bandwidths starting from 1.4 to 20 MHz. And as part of that, we also saw that how many resource blocks are there, which are supported for each and every LTE bandwidth.

And we discussed like this bandwidth supports are dependent upon LTE bands. All the bands cannot support all the bandwidths. Then we discussed about LTE architecture and interfaces, where we saw the mainly three modules, UE, UTRAN, and EPC. As part of UTRAN, we discussed about E-NodeB, we discussed about functionalities of E-NodeBs. Then we discussed about LTE EPC, and we discussed EPC in detail, where we discussed about MME functionalities, S-Gateway functionalities, P-Gateway, HSS, and PC-RF functionalities. Then we discussed about LTE interfaces, where we discussed about LTE UU interface, which is R interface. Then we discussed about S1 interface, which is very important between E-NodeB and MME, or EPC.

Then we discussed about X2 interface, S11 interface, S5, and S6 interfaces. So these are the table of contents for today's discussion. Today we'll be discussing first is LTE frame structure. So as part of LTE frame structure, we'll discuss about both the frame structures, FDD and TDD. Then we'll discuss about LTE resource block and resource elements. Here we'll understand what is a resource element, and what is a resource block, and how many resource elements are involved in a resource block. Then we'll discuss about LTE bearers, what are the bearers LTE supports. As part of that, we'll discuss about default bearers, dedicated bearers.

Then we'll touch upon QoS, that is quality of services, whatever being provided by LTE. As part of that, we'll discuss about various QoS services, GBR and non-GBR. The difference between GBR and non-GBR. And also we'll discuss about the QCIs. QCIs, QoS class identifiers, where there are different identifiers, QCI IDs for different different course elements. Then at the end of the session, we'll just summarize whatever we'll be discussing today. So these are the learning objectives. So the learning objectives for the students are to understand LTE frame structures, to be familiar with LTE resource block and resource elements, and to learn about various LTE bearers and quality of service.

So let's start with our very first topic, that is LTE frame structure. Okay, so the first type we'll be discussing is type 1, which is FDD. So as we know, we have already discussed in previous sessions, like FDDs having two different frequencies for uplink and downlink. So whenever UE and E0B communicate to each other, they have certain time structures that is divided into frames. So these are called basically radio frames or system frames. Here you can see that this is UE, this is E0B and they are doing data transfer to each other and they are doing synchronization and the talking to each other and that are in frames.

So frames are nothing but the timings. These are the timings. So here the time duration of one frame is 10 millisecond. So one frame or you can say one radio frame. So basically we'll be using the term radio frame or system frame throughout the session. This meant that we have 100 radio frames per second. So as one radio frame is 10 milliseconds, so in one seconds we'll be having 100 radio frames. Okay. So see, we have taken one frame and we have just extracted one frame and we have just tried to elaborate here.

So one frame will be having 10 sub frames. You can see here starting from 0 to 9. So one frame equals to 10 sub frames. Okay. And number of slots in one sub frame is 2. So here you can see one sub frame has been divided into two slots. Time slot 0 and time slot 1. That means its time slot will be having 0.5 milliseconds. Okay. So total 10 millisecond frame has been divided into 10 sub frames. So each millisecond, each sub frame, then one sub frame divided by 2 means 0.5.5 of time slots. Okay.

So one sub frame will be having 2 time slots. Then further you can see one time slot has been divided into this many number of symbols. So basically 0, 1, 2, 3, 4, 5, 6, total 7 number of symbols. Okay. So one slot is made up of 7 small blocks. This small block, small blocks you can see, these are nothing but symbols. Okay. One symbol is a certain time span of signal that carry one spot in the IQ constellation. You see even smaller structures within a symbol. Here, if you see this one, this one, this one. Okay.

So these are the smaller structures within a symbol. At the beginning of symbol, it is very small span called CP, which is cyclic prefix. And remaining part is the real symbol data. So cyclic prefix is basically used to reduce the inter-symbol interference. So we have kept a small, small gap here, which are the CPs, cyclic prefix. So, you know, to avoid the interference between two symbols, those are called inter-symbol interference, ISI. So there are two different types of CP. One is normal cyclic prefix and other is extended cyclic prefix, which is longer than the normal CP.

Since the length of one slot is fixed and cannot be changed, if we use extended CP, the number of symbols that can be accommodated within one slot should be decreased. So in case of extended CP, there will be just six symbols. Okay. So if this part, this gap, if we are increasing, then the symbol, number of symbols will decrease. But we cannot keep seven symbols with less duration because that means much duration is mandatory for one symbol. So you can see one time slot equals to seven OFDM symbols in normal CP and one time slot equals to six OFDM symbols in extended CP.

So this is all about FTD type 1. Then we'll move on to TDD, which is type 2. Okay. So now again, let's recall our TDD. So TDD as we know that is having same frequency for UL and DL. And we discussed about that we divide the same frequency into different time frames, different time windows for DL and UL. So you can see here. Similarly, here also frames are of 10 milliseconds. Okay. One radio frame or one system frame is of 10 milliseconds. And this frame has been divided into 10 SFMs, 10 subframes, SFs basically we call it and H of 1 milliseconds.

So till here it is same. But in FTD, this all can be of DDDDDD for downlink or it all can be for uplink depending on the frequency. But here as the frequency is same, so this time slots have been divided into three different paths. Okay. So we understand D is for downlink, U for uplink. S is what? S is basically you can see I have elaborated S as this spatial subframe. Okay. Spatial subframe is basically combination of both DL and UL. So D is only for DL, U is only for UL. But here as we know that in one time slot, we will be having seven symbols.

So in one subframe, there will be 14 symbols as there are two time slots. So those 14 symbols has been divided into two paths. Some of the symbols out of 14 will be part of DL symbols and some of them will be part of UL symbols. That is called DWPTS and UPPTS. That is called downlink pilot time slot and uplink pilot time slot. And there is a guard period GP. So, let us say downlink transmission is ongoing. For example, there are three symbols that belongs to downlink. Downlink transmission is ongoing. Now, we have to switch to uplink. Then there has to be some guard period. So, that guard period is this one.

Okay. So, this duration is symbol that is different based on the configuration. Okay. So, let us say as we talked about out of 14, there should be some part of DL and some part of UL. So, that is based on the different configuration. We will see in the later slides. So, this is the DL, UL configuration. This is completely defined by the spec. We have seven configurations 0, 1, 2, 3, 4, 5. So, this is the DL to UL switch point periodicity. And this is the subframe number. Okay. So, let us go to the last slide one more time.

So, as we have this 10 subframes. Okay. So, as we have this 10 subframes. Okay. Then based on what we can configure like which has to be DL, which has to be for UL, which has to be spatial. So, these are the configurations defined by the spec. So, you can see here for 10 milliseconds for 10 subframes, there are different configurations. So, for example, if I am configuring UL, DL configuration as 0. Okay. Then my first SF will be D. Second will be S. Third will be U. Fourth, fifth will be U. Again, sixth will be D. Seventh will be S. And eighth, ninth, tenth will be U. Okay. Now, again, the question is fine. D and U are fine. But what about S slot? Here, how will we decide that how many should be how many symbols should belong to DL and how many symbols should belong to UL? For that, there is one more table in the spec 36211, table 421. Okay. If you see that table, there are 10 different configurations. Okay. For spatial subframe.

So, let's say I am configuring 2 for spatial subframe. Then, in 2, the first 10 symbols will be for DL. 3 will be guard period and 1 will be for UL. So, 10 plus 3, 13 plus 1, 14. So, this is how we have distributed all our 14 symbols. So, any of the configuration if you take. For example, let's say 7. Then, 7 will be having 10 for DL, 2 for guard period and 2 for UL. So, 10 plus 2 plus 2, 14. Okay. So, this is how we configure the spatial slot.

Now, next topic is LTE resource block and resource element. LTE bandwidth is divided into subcarriers with a subcarrier spacing of 15 kHz. So, the whole bandwidth. For example, if we are taking 20 MHz. So, we had already discussed that 20 MHz will be having 100 resource blocks. So, that complete 20 MHz is divided into 15-15 kHz of subcarriers. I mean, it will be divided into different subcarriers having space between 2 subcarriers of 15 kHz. So, 1 resource element is 1 subcarriers. Okay. So, if you divide whole 20 MHz bandwidth into 1 subcarriers. Each having spacing of 15-15 kHz. Then, the 1 out of it in the frequency domain.

And, 1 symbol from the time domain. And, 1 symbol from the time domain. Will be 1 resource element. Okay. Resource block is the basic unit of resource allocation. So, why basic units? Then, means you cannot allocate less than a resource block. So, minimum allocation has to be a 1 resource block. Okay. So, if you are assigning for data or for signaling for anything. Then, at least 1 resource block you have to assign. You cannot assign like half resource block or 0.25 resource block something like that. Okay.

RB is defined in both frequency and time domain. So, this is how. Subcarrier and symbol. That we will see in the latest slides. 1 RB equals to 7 OFDM symbols into 12 subcarriers. 12 subcarriers means 50 spacing and into 12. So, total 120 kHz. That is 7 into 12 equals to 84 REs in normal prefix. Normal prefix. Why normal prefix? Because we have 7. We have considered here 7 OFDM symbols. Okay. Now, here is the visualization for the same. This is 1 radio frame having slot 0 to 19. So, you know, in 1 radio frame we have 10 SFs, 10 subframes. And in 1 subframe we have 2 slots. So, in 1 radio frame there will be total 20 slots. Starting from 0 to 19. So, this part we are aware that 1 slot will be having 7 number of symbols. Okay.

So, this is how the whole bandwidth. So, this is how the whole frequency bandwidth has been divided into subcarriers. So, subcarrier 1, 2, 3, 4, 5, 6, 7, 8, 9, 10 and so on. Okay. So, now you can see here. This is 1 symbol. Right. This is 1 symbol. So, this is 1 symbol and this is 1 subcarrier. So, 1 subcarrier in frequency domain and 1 symbol in time domain is 1 resource element. Okay. This is what we discuss is 1 resource element. Now, resource block. Resource block. Again, let's go to go back to the last slide. 1 resource block is 7 OFDM symbols into 12 subcarriers. Okay.

So, now you can see this part which has been marked in red is 1 resource block. Okay. Which is having 7 symbols and 12 subcarriers. Okay. Means 12 into 7, 84 resource elements. If it will be extended prefix then obviously will be having just 6 symbols. So, 12 into 6, 72 resource elements will make 1 RB. We further elaborated the same diagram. So, here you can see frequency 1, 2, 3, 4, frequency 12. This is 1 resource element. This is 7 OFDM symbols. Okay. And 7 OFDM symbols and 12 subcarriers. Basically, total 84 resource element. This is our 84 resource element. Is making 1 resource block.

And this is how resource block. And this is how resource block looks like in the frequency domain. If you see this is 1 slot. Complete slot. So, let's say we have 20 MHz. If you remember we had discussed like 100 RBs will be there in 20 MHz. So, this is how it looks like. RB 1, 2, 3, 4. Starts from 0 down. RB 0, 1, 2, 3, 4 and this will be RB 99. So, total 100 RBs. Okay. In 20 MHz. Now, let's move on to our next topic of today's is LTE bearers. Any bearer in LTE is pipe between 2 entities. Okay. Which is used to carry some information. It is a carrier to transfer some information.

And the end-to-end bearer. Okay. And the end-to-end bearer is divided into 2 parts. Okay. EPS bearer and Internet bearer. So, here you can see EPS bearer or the external bearer. Okay. And EPS bearer provides user plane connectivity between UV and the PDN gateway, packet gateway. Here you can see this is EPS bearer which is from UV to P gateway. EPS bearer is a complete bearer in the LTE system. Next, next part of this bearer is external which, you know, connects from P gateway to the peer entity. It could be any server, Internet server or anything.

Further, this EPS bearer is divided into 2 parts. One is S5-S8 bearer which is between S gateway and P gateway. And from S gateway to E node B and to UE, it is ERAB. Okay. Again, ERAB is divided into 2 parts. One is S1 bearer that, you know, based on the interface, the name has been, you know, kept based on the interface. So, between E node B and EPC, it is S1 bearer. And between UE and E node B is radio bearer. So, there are two types of EPS bearer. One is default and another is dedicated. So, default is established during the registration procedure.

This can be multiple bearers on top of, there can be multiple bearers on top of it to provide multiple PDN connection of multiple quality of services. Those are known as dedicated bearers. So, these are the differences. So, as we discussed, this is established during initial attach time and normally established during call time. Allocate an IP address to the UE does not allocate an IP address. It is It is associated to one of the default. It does not have specific QoS. It has specific QoS information. So what is QoS? QoS provides quality of services and differentiates between subscribers and services. Okay. So like premium subscribers can be prioritized over basic subscribers while real-time services can be prioritized over non-real-time services.

The importance of QoS increases during period of congestion and unloaded network is able to satisfy all subscribers and all services. As the network load increases, then this privatization determines which subscriber and services are able to maintain their performance and which experience a loss in performance. QoS is applied between the UE and P-Gateway within the LTE network. That is, it is applicable to an EPS bearer generated from the combination of ERAB and S5-S8 bearer. So we saw like one EPS bearer is having two parts. One is ERAB and another is S5-S8. Each EPS bearer is assigned with one QCI ID. Okay. So whenever we will be creating any of the bearer, any EPS bearer, each bearer will be having one QCI ID. Okay.

And each bearer, each EPS bearer is categorized as GBR or non-GBR. So what is GBR and non-GBR? So GBR resource type means the bandwidth of the bearer is guaranteed but not in the case of GBR. So GBR is basically the full form is guaranteed bit rate. So let's say we have configured 2 GBPS, the GBR or in LTE, not 2 GBPS, let's say 400 Mbps for 1 GBR for the bearer. So it means this 400 Mbps has to be given to the UE at any cost. So that is the guaranteed bit rate. Okay.

But in case of non-GBR, it does not guarantee like 400 Mbps might degrade to 300 or it might go to 100 Kbps as well. Okay. So that is the difference between GBR and a non-GBR. Only a dedicated EPS bearer can be a GBR. So any default bearer when we are establishing during the call time is non-GBR always. So whenever we are creating any dedicated EPS bearer on top of a default, then that can be either non-GBR or GBR. Okay. A default EPS bearer is always non-GBR. Okay. We discussed already. QCI range, that identifier, right, we discussed about that QCI ID for each bearer we provide.

That is 1 to 4 is for GBR and 5 to 9 is for non-GBR. So there is a table provided by the specifications which tells about this QCI ID. So this is the table. Here you can see these are the QCI ID. 1, 2, 3, 4, 5, 6, 7, 8, 9. So 1, 2, 3, 4 belongs to GBR and 5 to 9 belongs to non-GBR. So here you can see the priorities for each QCI. So let's say I am having QCI 4. This will be having less priority that is 4 with respect to QCI ID 1 which is having priority of 2.

And for each QCI, for each bearers, there is packet delay budget. Okay. So this can be the maximum delay bearer, that bearer, particular bearer while transmitting the data can suffer. That is 100 millisecond for QCI ID 1 and similarly 300 millisecond for QCI ID 4. This is the packet error loss. Packet error loss is basically this is the, this is what the maximum packet error loss should be there in a particular, you know, QCI ID. So let's say I am configuring QCI ID 3. Then it has to experience a maximum of 10 to the power minus 3 as packet error loss rate.

Here are the example services. So let's say I am just using a conversational voice. Then voice, you cannot know break. The minimum requirement for voice has to be there. Like for example, 100 kbps is required for voice. Then 100 kbps should be a GBR. You cannot give less than 100 kbps. Otherwise, you will not be able to talk. You will not be able to listen. Okay. Then conversational video live streaming. In live streaming also, let's say if you are setting a particular quality, HD quality, then if you are going down to that particular data rate, for example, if you do any surfing or if you watch any OTT platform, then you can see whenever you are setting any of the quality for HD, let's say HD, it will automatically show you that 2 gb per minute or 2 gb per hour. So let's say in 1 hour that will take 2 gb. So that is a GBR.

You cannot give less than 2 gb for 1 hour. Otherwise, you will not be able to see the live streaming. This is for real-time gaming QCI ID 3. Again, non-conversational video, non-conversational video is like buffered streaming, like YouTube and all. Then IMS signaling, that is for Volte, voice over LTE, which uses QCI ID 5, that is non-GBR. Then video, buffered streaming, TCP-based, voice, video, interactive gaming, this all comes under non-GBR. 8 and 9 is for video, buffered streaming, TCP-based, www, email, chat, FTP, F2P, P2P file sharing, progressive video, etc.

That is it from today's session. We'll quickly summarize whatever things we discussed today. So we discussed about frame structures. We discussed about FTD and TDD frame structures where we discussed like one radio frame is having 10 milliseconds and each radio frame is divided into 10 different SFs of 1 millisecond each. And each SFs subframe is divided into 2 parts, which is 2 time slots of 0.5 milliseconds each. Then we discussed about various resource blocks example. And we understood what is a resource element. So one resource block is made of 84 resource elements in normal prefix and 72 in extended prefix.

Then we discussed about LTE, EPS and radio bearers. So EPS bearer is divided into 2 parts, ERAB and S5S8. And again ERAB is divided into 2 parts, is radio bearer plus S1 bearer. Then we discussed about LTE quality of services, QOS. As part of this, we discussed about GBR versus non-GBR. What is the difference between a guaranteed bit rate and non-guaranteed bit rate? Then we discussed about QCI IDs, various QCI IDs supported in LTE. And we saw that what is the requirement of each QCI and also we saw the examples where can we use what kind of QCIs.

That is it from today's session. Thank you for joining.

Want the rest of Overview of 4G Networks and evolutions to 5G?

Get the full course syllabus and fees.

The full course is paid (₹40,000). We'll send the syllabus and call you back within one working day.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Full course · paid

Unlock the full Overview of 4G Networks and evolutions to 5G course

The remaining 14 lessons, mentor-reviewed projects and a certificate come with the paid course (₹40,000). Leave your details: we'll send the syllabus and fees and call you back.

Get the syllabus and fees

A counsellor calls you back within one working day.

By submitting you agree to our Terms and Privacy Policy.

Grow by Skill-Lync · free lesson

Start watching

Free, no payment. Leave your details once and every free lesson on Grow plays straight away. A Skill-Lync counsellor may call you about the full Overview of 4G Networks and evolutions to 5G course.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.