← Previous lessonFree lesson 3 of 3 · lesson 3 of 52

Unlock all 52 lessons of Network Planning for Cellular and WiFi SystemsFull course ₹40,000 · paid

Price & syllabus
Free lesson · 33 min · no payment

Cell Capacity Calculation Example and LTE Frame Structure

A free lesson from Skill-Lync's Network Planning for Cellular and WiFi Systems course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “Week 1 Session 3”

What will you learn in this free Network Planning for Cellular and WiFi Systems lesson?

The instructor works a 2 km radius example by hand, from area and population to 314 active users, 4.71 Gbps demand and spectral efficiency in 10 MHz. The lesson then describes LTE eNodeB protocols, OFDM transmit chain, frame and slot timing, random access sequence and the resource grid.

  • Area, population and active user calculation
  • Total throughput and spectral efficiency demand
  • LTE control plane and user plane layers
  • Frame, subframe, slot and resource grid

What comes after lesson 3?

Later in Skill-Lync's Network Planning for Cellular and WiFi Systems course (paid): lesson 4, Week 1 Session 4; lesson 5, Week 2 Session 1; lesson 6, Week 2 Session 2. The full course has 52 lessons (25 h 45 min of video); see the course overview or its price and syllabus.

Lesson transcript

Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.

So in this session, as I said before, we'll do a deep dive on the QoS and see how their role plays out in an example. So I have shown an example here where I take a circular area of 2 kilometer radius and that needs a cell tower. So that's the scenario I'll be considering. But in this session, you know, it will require a little bit of whiteboarding. Just the slides will not be sufficient. So since we don't have a whiteboard here, what I will do is that I'll open up an empty notepad screen parallelly with this and then we'll go back and forth between this slide and that notepad screen and I'll write down a few numbers and I'll see how to crunch them, how to solve them, you know, all these calculations I'll be showing you as a demo.

So instead of putting it on a slide, I thought it'll be good to go over it with you in a live fashion just by typing it on the notepad as we are talking. So that'll be one aspect of this session. And then after that, we'll do a little bit of deep dive on the LTE metrics as well. Slightly advanced version of these metrics and we will see how these metrics tie into the LTE standards. And then we'll try to relate it to some of the existing bands that are being used, some architectures, frame formats that are used in LTE and so on.

So that'll be the essence for this particular session. So with that, let's get into the scenario and work it out. So now let's consider a sample scenario where we look at the quality of service and KPI evaluation. OK, let's assume a circular area of two kilometer radius that needs a cell tower. OK, so somewhere in, you know, let's say a medium, not so dense, like a medium urban setting. So there is a circular area of radius two kilometers and that needs a cell tower for coverage.

And some numbers that are given here is that the population density is 500 people per square kilometer and 50 percent of the population is expected to subscribe to the new service. OK, so again, there's two kilometer radius. So that has certain area in square kilometers. And then it has 500 people per square kilometer. That's the density. OK, so now from that, you'll have to calculate what will be the total number of people living in that area. And then, you know, 50 percent of that population is expected to subscribe.

OK, so let's stop there and do some calculations. OK, before we go too much into the numbers, let's stop there. Let's take the first three bullets and let's try to process them. So I'll show you how to do it. You don't need any special tool. Just a calculator and a paper pen should be sufficient. Let's look at some of the math that that goes here. OK, so a circular area of two kilometer radius. So let's first calculate the area of this circular region. OK, so it's given that the radius is two kilometers.

So that means area would be something like let me expand the font size. So the area would be pi r square. Right. So it will be like three point one, four times two times two. And that will give me let me just quickly calculate it. Twelve point five, six. OK, so it's twelve point five, six square kilometer. OK, since this two and two are in kilometers, the resulting area would be square kilometers. OK, and the next number, if I go back to the slide, it says the population density is five hundred people per square kilometer.

OK, now what this means is that this is, as I said, it's a density number. It's not a total number of people living in that area. OK, so if five hundred people live in one square kilometer, how many people will live in this much square kilometer? So the total population would be. Population density times the area. OK, so that would be population density is five hundred people per square kilometer and the area is twelve point five six. OK, so now let's calculate the population density. Five hundred times twelve point five six.

That would give me six to eight zero. So these many people are living in that area in the circle of two kilometer radius. OK, just to be more descriptive. Now, that's the total population. OK, so now we have processed the three bullets. First bullet is the radius. The second bullet is the area that we're calculating and then the population density. OK, the third bullet here is 50 percent of the population is expected to subscribe to the new service. OK, let me go back to this. Yeah, 50 percent of the population.

So let's find out what is 50 percent of this population. OK, and that would be six to eight zero divided by two. Right. So that's 50 percent of the population. So if I just divide this by two, that will give me three one four zero. People have subscribed. To the new service that you're providing. OK, so that's your subscribers. OK, now let's go back to the slide. It says roughly one in 10 subscribers are actively using the data at a given time. OK, now next step is calculating the active number of users.

OK, so let's give it a heading. OK, this one is number of subscribers and this one is population. OK, so the rest is obvious, I guess. So let's just highlight this. Now let's get into active number of users. OK, so it is one in 10 people are active. So out of these many subscribers, OK, the active would be three one four zero divided by 10 because there's only one in 10 or you can think of it like times one by 10. OK, so one in 10 are active and that would give me three one four simultaneous users.

So that's that's that's the right way to describe it. So at any given time. So let me make a statement here. At any given time, instant. Three hundred and fourteen people or smartphones are simultaneously using. The seller service. OK, now let's go back to the slide and see what happens next. Now, each user is expecting a throughput of 15 NBPS. And how many users do we have? Three one four users. So at any given time. So the instantaneous throughput requirement is three hundred and fourteen people and then 15 NBPS each.

So that would give you, let's just calculate it. So four seven one zero NBPS or I can also write it as four point seven one GBPS. OK, so that's the total throughput requirement. Instantaneous total throughput requirement. That means the total cell throughput. OK, so the entire cell at two kilometer radius coverage will be requiring this much throughput at any given time, instant, because three hundred and fourteen people could be active. I mean, it need not be exactly three hundred and fourteen could be here or there.

But on an average, you know, it's given us roughly one tenth. So that's why, you know, we land in this number. So and now let's assume there is an available bandwidth of 10 megahertz. So now this is a constraint. OK, now this much NBPS needs to be served within the limited bandwidth. So the bandwidth available is 10 megahertz. OK, now the next step before we go to area, you know, the next bullet here that says that what is the area spectral efficiency required to serve this demand with an oversubscription factor of one point three.

OK, now let's just try to consume this oversubscription factor. As we have defined earlier, it is basically, you know, if this is the instantaneous throughput that needs the oversubscription throughput would be the instantaneous throughput times the oversubscription factor. OK, and in this case, the oversubscription throughput is four point seven one GBPS times the factor is one point three. OK, I just multiply this by one point three and that will give me four point seven one times one point three. It's six point one to three GBPS.

So this needs to be served in a bandwidth needs to be served in a bandwidth because that's the max bandwidth that's available. So even if you use all of it, this needs to be served. OK, OK, so that that's your 10 megahertz bandwidth and this needs to be served for the entire cell coverage. Now, with this one, we have to find out what is the area spectral efficiency. OK, now let's try to find out what is the spectral efficiency first of all, and then we'll go to area spectral efficiency.

So we're going to calculate two things spectral efficiency and then we have area spectral efficiency. OK, the spectral efficiency is given by the throughput divided by our bandwidth available. OK, and that would be six point one to three divided by 10 megahertz. OK, and that will be. So it's 6.123 in GBPS, right? So I'm going to put a G there. And that will give me like 6123 divided by 10. That will be like 612.3. Okay. And the area spectral efficiency would be divided by the total area that you have here is 12.56. That would be 48.75. And the units would be bits per second.

Per hertz per square kilometer. Now, again, this may not be always realistic because I'm showing numbers that are really high. Typically, this is not the case because it's just an example that I've picked the numbers that are extremely high. Normally, you know, you either have more bandwidth for these type of scenarios. 10 megahertz was just an example. And the oversubscription factor might be too much. So this is just a 15 MBPS is more like a Wi-Fi throughput that you get these days. It's normally like 1 MBPS or even less than 1 MBPS for cellular data these days.

So, but this is just a really extreme example, but this is not a very realistic one, just to give you a warning. And this is basically how you do the calculations, just to give you a flow of how the calculations are done. Okay. So that's the purpose of this particular slide is to give you a sample quality of service and KPI evaluation. So what we are looking at it is here, we have a target and we are trying to achieve that. And now this shows that you need to serve this much of area spectral efficiency, which is very expensive or which is very high.

You cannot serve this much bits per second per hertz in a square kilometer. So that becomes a really hard problem. But, you know, there's just a way to, you know, to do the flow or the flow of calculation just to assess the system and how easy or how difficult it is to get that network plan for this particular set of requirements. Now with that, let's move on to the LTE advanced architecture. So we have, I have broken down, you know, a base station's architecture. So let's, let's take a closer look and see what these different blocks in the base station do.

Okay. So, uh, we normally use this term of ENB, um, or, uh, E node B, which is known as, uh, enhanced node B is just a short form of that. Uh, B stands for base station node is for that particular site is what we call as node. Okay. So it has these, uh, components as shown in this diagram. So we have already seen the service gateway and then there's also another block parallel to that, uh, known as the MME block, which is for mobility management entity.

So this takes care of any sort of, uh, connection requests, mobiles entering and leaving the cell because of handoffs. Um, so it takes care of all these requests, keeps track of that. Um, and after this, we have the access stratum. So far what we call this as non-access stratum, NAS, uh, the reason we, we call this as non-access because it's not related to the access. So these are all working directly for the access. So, uh, the access stratum primarily consists of the E node B. The bigger block as you see here is the E node B and there could be multiple E node Bs.

And the interface connecting the E node Bs is known as X2 interface. Okay. Um, and again, this whole, uh, structure can be broken down into control plane and user plane. Okay. User plane primarily relies on the operations that help, uh, to create data packets and process those data packets by TCP, UDP and IP. Whereas the control plane on the other side takes care of a resource, um, radio resource control protocol, where, whereas it will send you all the signaling messages that are exchanged between two base stations.

Okay. Or between a base station and a mobile. So that's what your control plane does versus your user plane. So that's just one way to define a user plane and a control plane. So user plane primarily consists of these, uh, structures, which is PDCP, RLC and MAC, and then the physical layer. Whereas the control plane primarily consists of RRC, which is the radio resource control protocols. So, and then we have this other item within the mobile management, you know, as NAS, which takes care of connections, new connections, authenticating them, adding them to the network, et cetera.

And as we discussed, you know, RRC is the control plane thing. It takes care of quality of service management, mobility, and security. The remaining three are very important to note because they're on the user plane and they deal with the data. So they're basically different layers of processing the data. The physical layer first processes the physical signals that are received and generates them as bits that can be interpreted by the higher layers. And this higher layer, you know, just deals at a packet level. You know, it gets the packets.

It makes sure multiple packets are received, you know, by, by performing multiplexing actions, uh, it, it, it sends a hybrid, uh, automatic repeat request, which means if the packet is received, um, has, let's say it's a lot of errors. Then it sends the, uh, request back saying that, um, it was not received properly or it, it, it may not even send a request sometimes, which means that, uh, the transmitter will know that the packet was probably not received. So it will send it again. So all those feedback mechanisms are included in this and it prioritizes based on, on which channel needs first, uh, priority, et cetera.

Um, RLC here, more, more, this is more like, uh, um, a radio link control channel. Um, it's, it's slightly higher layer. It takes care of, uh, error correction through, uh, automatic repeat request. Uh, it does concatenation, segmentation, and reassembly of, uh, RLC data segments. Um, it also helps with, uh, duplicate detection. Um, and, and other, uh, protocols that are related to error detection and recovery. Um, so that's what the RLC is doing. Whereas PDCP, on the other hand, uh, is a higher layer protocol, slightly higher layer.

It takes care of transfer of user plane data and control plane data. Uh, it performs header compression, uh, ciphering, uh, integrity protection, et cetera. So, uh, that's an overview of the LTEs, um, um, UTRAN architecture. And, uh, the, the UTRAN architecture here, uh, is a very generic system. It can be very specialized as, as, as, as the standards evolve. Now, let's look at some of the spectrum, um, allocation, uh, aspects in LTE. So, uh, as I said before, a 5G, uh, tends to go to higher frequencies, whereas the 4G LTE still stays within the sub 60 GHz frequency range, which means within those, uh, frequency ranges, there are, uh, limited set of bands that we're using.

In the previous example, I gave you a 10 MHz band, which is not sufficient, which is very small. Uh, but then the bands, uh, you know, are up to 100 MHz, um, uh, is available. You know, that can be used. And there are different bands that are specified. Sometimes it can be like, uh, contiguous bands or it can be like non-contiguous bands. And then you can have two different bands that are being used. So, uh, these are all some of the bands that are specified for LTE uses, um, such as 450 to 470.

So there's a 20 MHz band. Um, and this is even larger band here, um, uh, which has, um, and then this one is another band. And then you have like 2.4, 2.3 to 2.4 GHz band and the, and the band in the CBRS side, which is the 3.4 to 4.2. 4.4 to 4.9 is very rare. And this sort of tends towards the, you know, much, much higher band and has, uh, poor propagation characteristics. So, uh, up to 100 MHz is allowed for usage in LTE and multiple 20 MHz bands can be aggregated in order to create a 100 MHz band.

Um, and normally, uh, there is a frequency and time aspect to the data allocation. Um, and it's up to the scheduler, uh, by scheduler, I mean something that's operated within the base station to schedule when to send the packets and in what frequencies they need to be sent. So that's why there's a frequency domain access and a time domain access. They can overlap because they're in different frequencies. So for example, user one could be using all the frequencies, but at a given time. And then once that slot is over, a user two can step in and then, uh, they can use all these frequencies at their given time slot.

And similarly, user three, um, it can be done in that way, or it can also be, um, done in this way where, uh, user one can use a limited number of frequency resources, but can stretch over a longer time and user two can overlap because there will be no interference because they're in completely different bands. Um, and then once it's over, uh, user three can step in and can use the bands that are overlapping with the user one's band because user one has stopped sharing after this time slot.

So there is a gap here after which user three has a lot of flexibility to use, uh, all the bands if necessary. So that's how bands are dynamically allocated. Again, that depends on how the channel is currently being used and how it can be evolved. So here is a, uh, LTE system architecture and basic frame format. Uh, again, this is not a course on LTE specifically, but it's good to understand what's happening behind these, uh, uh, E-Node B base stations or what's happening inside a device in terms of, uh, wireless, uh, communication system processing.

Um, again, we don't have to do it too much of a deep dive into that, but I'll just gloss over these things at the high level so that you'll understand what's happening and then you'll relate it to, uh, the network planning, um, uh, framework that we're going to get into. So we're just going to go over the block diagram at a high level, um, and see some of the design challenges that typically people face in this area. And then finally we'll conclude with the frame format.

So the block diagram here, um, you know, starts with a binary data input, which is a set of bits. As I said in the previous diagram here, um, the five basically processes the bits. So those bits are given from the upper layers, you know, with a header and everything added. So it's, it's a set of bits. Uh, the five does not know which is header, which is the data. So it just, uh, it takes everything as a set of bits. And, uh, the very first step is mapping those bits to a symbol such as a complex symbol.

You know, it could be a four quam QP. SK or 64 QAM, depending on the modulation size that is available. It includes some more processing where it does some pulse shaping. And then after that, it does IFFT. Now, these are all OFDM-related processing. After IFFT, it adds cyclic prefix, and then some windowing is done. And then the data is converted to the analog equivalent. Right until this point, it's in digital form. Then it's converted to analog form. And then after that, it can be attached to any type of system.

Here it says optical front-end, but it can be, again, a wireless front-end as well, OK? So because the whole structure remains the same, just the front-end could change. Similarly, on the receiver side, any front-end could receive the data and then have an ADC, which is analog to digital converter. It will send you the digitized samples here. And then this is an OFDM receiver processing where your cyclic prefix is removed. And then fast-forward transform is done. And, again, some more processing happens, some channel estimation, and then it does some MIMO processing to remove some of the interference cancellation across if there are multiple antennas.

And then, again, finally, it comes back to the binary output because what happens here is demodulation. That happens on each receiver chain. We have multiple receiver chains here. Each receiver chain performs the demodulation and gives you the bits back. And also, if you notice, on the transmitter side, there could be multiple transmitter chains. Each chain has its own processing, and it's all combined here. So this is basically the overall architecture of how things process in LTE. And the standards here refer to this one, not most of the front-end.

Okay, what kind of processing and framing happens here? Now, in designing this type of a system, the major challenges that we face is the receiver sensitivity, which means you need to have a receiver that is sensitive to a certain power level, which means, okay, let's just first define what is receiver sensitivity. Okay, receiver sensitivity is the minimum power at which the receiver can meaningfully detect the signal, okay, and can decode it into its corresponding bits. So receiver sensitivity here refers to the power level at which it can decode it.

So the way it becomes a design challenge is that you need to design it at much lower sensitivity levels. Even if the signal is very low in power, the receiver should still be able to pick it up. Now, this is primarily dominated by the noise flow. So no matter how low the signal is, it also depends on how high the signal is when compared to the noise. If it's immersed in the noise, then the receiver will not be able to detect that signal. So that's why receiver sensitivity becomes important.

Not just that, so many nonlinearities kick in, especially in the RF front-end. We expect the whole system to be a linear system where everything can be scalar multiplications and processed properly. But in reality, there will be so many nonlinearities. So what do we mean by nonlinearity is it's some sort of a non-ideality. When things are not linear, it's hard to recover them. If it's a linear process, then you can always undo it and recover it. When it's a nonlinear process, then it's hard to recover it.

That's the problem with nonlinearities. Again, that becomes a design challenge to come up with a circuit design that has minimal set of nonlinearities. And reciprocal mixing is another aspect here, which means when you're down-converting the channel, many unwanted spurious tones could occur and that could cause some sort of mixing issues. The ADC dynamic range is also an issue because when you have very low sensitivity, the ADCs need to operate at the low power levels as well. Because typically, ADCs have a range. It operates. What do I mean by the range?

It's just the difference between the lowest power level and the highest power level. Roughly, an ADC can operate. That has to be very wide and that sometimes increases the cost of the ADC. Now, that operates at wider dynamic ranges. So ADC dynamic range is also a design challenge. So normally, when you are doing a network planning or trying to place a few base stations, the received power levels from a nearby cell phone could be much higher than a received power level from a very far away cell phone.

Because we have seen in the previous example, a cell tower can have a radius of up to 2 kilometers. There could be cell phones that are right underneath the cell tower. The signals received from those cell phones would be at much higher power. They will be operating at the higher power range of that ADC in the base station, whereas cell phones that are really far away from the base station could be sending out signal that is received at an extremely low power. So the ADC needs to have this dynamic range to target both these ranges.

So that becomes a design challenge. FFT size is a fast Fourier transform size that directly depends on how many users the system is trying to multiplex in a given band of frequencies. Normally, the higher the FFT size, the more multiplexing can happen if there is more bandwidth. But the FFT size is also computationally expensive, which means it requires a lot of resources. The more the FFT size, the more resources it would require. As a result, we will have to switch to multiple FFT chains so that we can separate it and then use multiple frequency shifts and then carrier aggregation.

And it gets a little bit more complicated if you try to reduce the FFT size. But if you increase the FFT size, all the complexity falls on the digital processing. So that is the hard part here. Yeah. So, again, FFT design is more like a digital system design challenge. So those are all some of the design challenges that people typically go through when they're designing these devices. And from a network planning perspective, you need to look at it, you know, what are the limitations or the challenges that the designers face?

And based on that, you can come up with an innovative network design that can overcome these challenges for them to design. And it might even make them easier to design these things that can bring the cost of that equipment down. So the next item here is the frame format. So, as I said, you know, if I go back to the slide, you know, the Mac gives the FI a set of frames that are sent out. And the FI treats them as a series of bits rather than frames or having a header and a data.

Whereas when it comes to the Mac, it treats them as header data. So there are so many differentiations here. That's what we're going to study in this frame format. So frame format basically represents how the data is arranged as a frame and then how they are treated at a higher layer. OK, so normally in LTE, one frame is of 10 milliseconds duration and one frame is divided into 10 sub frames. Each sub frame is a one millisecond duration. So one and 10, it's easy. Right. So 10 milliseconds is one frame.

One millisecond is one sub frame. Now you can break down the sub frame into a slot, which is half of that sub frame. And it is 0.5 millisecond. OK, now each slot is 0.5 millisecond and each slot contains seven OFDM symbols. OK, and each OFDM symbol contains a cyclic prefix and then a data part. So as you can see in blue here, as it is indicated, each OFDM has a cyclic prefix and then there is a data part. Cyclic prefix and then a data part. So seven OFDM symbols comprise of one slot and two slots comprise of one sub frame and 10 sub frames comprise of one frame.

So the MAC could take this entire frame and then process it and separate these symbols out or maybe add another header to it and send it to the higher layers. Whereas physical layer breaks it down further and then treats them on a symbol by symbol basis. And each symbol goes through this whole chain and comes back here. That's how the physical layer treats it. The physical layer treats it on an OFDM symbol basis, whereas the MAC layer treats it on a frame basis. So that's the understanding that we need to have in terms of the system architecture and the frame format and some of the design challenges.

Now, when we look at the timing diagram, so timing diagram here represents how the different data and control communication is orchestrated. OK, so this whole diagram can summarize this. Normally, the base station on the right side sends a broadcast information. OK, so it's more like a advertisement. It says that, hey, I'm available here for your service. And then any of the UV can pick it up and then send a random access preamble. It can send a PRACH. PRACH is a physical random access channel. And then an access response message is sent back on the control channel because this gives some information on saying that the handshaking is done and ready for transmission.

And then the user equipment can send a connection request on the uplink, which is known as PUSCH, which is a physical uplink shared channel. And then once this is given, it's like a trigger. And then the base station starts sending the connection on the PDSEH, which is the physical downlink shared channel. So this is the data channel. This is the uplink data channel, the downlink data channel. And this is the downlink control channel. This is more like an uplink or random access channel. So this is the order in which the sequence is initiated.

And these are all the different frame formats. So they have certain structures associated with them. So we saw how PDSEH looks like in this one. This is a PDSEH example. PDCCH could be in a different format. PRACH could be in a different format. And PBCH, which is physical broadcast channel, could be in a different format. So they just have their own frame formats and they're treated separately. And they could have certain different power levels as well. So, for example, PDCCH can have a slightly higher power level so that it can reach to a wider area.

And it could have a smaller bandwidth because there's not much data that is being sent. It's more like a reachability purpose. So, yeah, everything could vary in its own perspective. When you are planning the network, you need to consider not just the data, but also the control part and see, you know, whether the control part can reach. Also, you should see the broadcast part can reach, you know, because the broadcast part has to reach. Only then these cells will be able to talk and make a handshake with them and then create that connection request.

So this is the whole process that needs to be. And as a network planning engineer, you need to take this into account and ensure that each and every step goes through the network that you're delivering. So this is an LTE resource grid. Basically, as I said before, the data can be mapped in time and frequency. And here it shows how it's being mapped. So here the y-axis represents the frequency, which is the subcarriers. As I said, there are 12 subcarriers in a resource block. And the x-axis represents the time. So there are like seven symbols. So each block corresponds to one OVDM symbol.

There are seven symbols in one slot, two slots in one subframe, and then 10 subframes to create one full frame. Now, if you look at the colors here, that will give you some idea. Let's start with blue. The blue represents PBCH, which is the physical broadcast channel. So what's happening here is it's just broadcasting or advertising using these resources here, a bulk of these resources, just for advertisement purposes. So the base station is advertising that it exists. That's all. Now, any of the UEs will pick it up.

It can pick up and it can send a response back, saying that I'm ready to connect. And once it is sending back, then it can use some of the synchronization channels to time synchronize between the base station. And then it will send the control channel using the PDC-CH, which is this one. And I believe all the white is for the data channels. OK. And there are also some of the red channels here. The reason for sending red is for reference signals. These are all cell-specific reference signals that will give the UE some information about the cell that is being transmitted.

And based on that, the UE will know which cell to connect to. So sometimes it may not, it might be in a handoff. So then it knows it has handed off to another cell. So things like that are being conveyed here. So it's just a matter of arranging this grid. Again, LTE spec gives you a detailed information of how this can be done. So to conclude this session, you know, we have primarily focused on LTE frame formats, especially on different channels, such as the broadcast channel, synchronization channel, cell-specific reference channels, of course, the downlink control channel, uplink control channel, and different channels like this.

So we have seen the purpose of all these channels. Primarily, you know, we have seen a lot of abbreviations here. So I highly recommend, you know, referring to an LTE abbreviations PDF files or textbook that's generally available online. You can Google it and find a list of these abbreviations. And it's good to print them and keep it handy because as you are working out, as you're studying a lot of these things, people tend to use these abbreviations a lot. So it's good to have a print document in your hand so that, at least in the beginning, so that you familiarize yourself with all these abbreviations there.

So in essence, for this session, we have done a little bit of advanced study on the LTE frame format, the system architecture. And of course, in the beginning, we studied an example for cell planning. With that, we followed up with some of the deep LTE stuff here. So with that, we'll conclude for this session and we'll continue in the next session.

Want the rest of Network Planning for Cellular and WiFi Systems?

Get the full course syllabus and fees.

The full course is paid (₹40,000). We'll send the syllabus and call you back within one working day.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Full course · paid

Unlock the full Network Planning for Cellular and WiFi Systems course

The remaining 49 lessons, mentor-reviewed projects and a certificate come with the paid course (₹40,000). Leave your details: we'll send the syllabus and fees and call you back.

Get the syllabus and fees

A counsellor calls you back within one working day.

By submitting you agree to our Terms and Privacy Policy.

Grow by Skill-Lync · free lesson

Start watching

Free, no payment. Leave your details once and every free lesson on Grow plays straight away. A Skill-Lync counsellor may call you about the full Network Planning for Cellular and WiFi Systems course.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.