Lesson finished
Up next: Distribution Systems and Load, Demand and Plant Factor Example
Unlock all 51 lessons of Introduction to Electric Power SystemFull course ₹40,000 · paid
Power System Structure: Generation Plants and Transmission Lines
A free lesson from Skill-Lync's Introduction to Electric Power System course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “Week 1 Session 2”
What will you learn in this free Introduction to Electric Power System lesson?
This lesson shows the three parts of a power system and the supporting protection and control devices. It compares thermal, nuclear, hydro, wind and solar plants, then explains transmission voltage levels and the short, medium and long transmission line classes with their models.
- Generation, transmission, distribution structure
- Hydro, wind and solar plant pros and cons
- Betz limit of 59.3 percent for wind turbines
- Short, medium and long line models
What comes after lesson 2?
The next free lesson is lesson 3, “Distribution Systems and Load, Demand and Plant Factor Example” (29 min). Later in Skill-Lync's Introduction to Electric Power System course (paid): lesson 4, Week 1 Session 4; lesson 5, Week 2 Session 1; lesson 6, Week 2 Session 2. The full course has 51 lessons (22 h 21 min of video); see the course overview or its price and syllabus.
Lesson transcript
Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.
Hey guys, welcome to session 2 of week 1 module. In the session 1, we have discussed the perspective of electrical energy. We have discussed the type of energy sources like drawn renewable and renewable energy sources. We have discussed the benefits of renewable energy sources. We have also discussed about how electrical energy is important to us and how it is important for all round development of any country. The per capita consumption of electrical energy is a very reliable indicator to represent the development of any country. That's why electrical energy is very important in any growth of any country. We have discussed the power system in India, its size, the achievements of power system in India and the challenges associated with Indian power system.
We have compared the power generation in India. We have compared the Indian power system and the power generation in India with some other developed and underdeveloping countries around the globe. Now, in the session 2, we will go some deep in the technical aspect of power system. We will discuss about the power system structure. Then, the three main components of the power system structure, which are generation, transmission and distribution. So, among these three in this session, we will discuss the generation system and the transmission system in detail.
So, let's begin with the power system structure. Here, the structure of the power system is shown. Typically, the power system has three main parts, generation, transmission and distribution. The generating station is shown as red in color. It can be any large or small power plant of any type like thermal, hydro, nuclear or renewable based. From generating station, the electrical energy transmit through transmission system at very high voltage of 400 kV or 765 kV. The voltage level shown here like 765, 500, 345, 230 or 138 kV at the transmission line is shown here as per the American standards or United States of American standards.
Here in India, for the transmission, we use 400 kV or 755 kV. So, from transmission system, the power goes to the distribution system. Here, the green color system is shown as the distribution system. We can also see at the transmission system level there might be some load connected to receive their power. Usually, these types of load are heavy industries like steel plants. They need huge amount of power and their power requirement can be fulfilled at transmission line itself only. That's why the heavy industries like steel plant receive or they get their power requirements directly from the transmission line itself.
So, other type of loads like some industrial, commercial or the residential load, they receive power through distribution system. At distribution system, the voltage level is low compared to the transmission level. So, step down transformer is used here which step down the voltage from 138 kV or 230 kV or any other voltage level at high voltage level to the required or the desired low voltage distribution side voltage. From here, the power requirement of the commercial, residential or the industrial loads are fulfilled. As we have discussed that there are three main components generation, transmission and distribution for any power system network.
Other than these three main components, there are some other supporting components for the proper and reliable operation of power system. So, in addition to generation, transmission system, other devices are required for the satisfactory operation and the protection of power system. They include loads, control units, protection devices, reactive power compensators and instrument transformers, circuit breakers, relay. These are all individual components required for the satisfactory operation or for the reliable operation or for the uninterrupted operation of the power system. So, as a consumer, we always want that the power supply should be continuous and there should not be any interruption in the power supply.
The quality of the power supply, the quality which means the value of the voltage level, the frequency of the power and the harmonics in the voltage and current should be low. So, that's why for a high quality power, we mean that the voltage should be constant at the specified voltage. The frequency should also be constant at specified voltage and the harmonics in the voltage and current should be as low as possible. So, for the satisfactory operation, these devices also like circuit breakers, relay, fuses and lightning arrestors are also equally important.
Then there are some control centers, they are equipped with online computers performing all the coordinations. So, in this way, other than these three main components, some other components are also required and they are also the essential part of our system network. Now, moving towards the three main components, generation, transmission and distribution, we can go in detail with all these three systems. So, one by one, we can start with the generation system. So, generation system as I have already told that the power where it gets generated is known as the generation system.
So, electrical energy, it is a form of energy, it should be or it gets converted from any other form of the energy. It may be chemical, mechanical or the kinetic energy in some other form, in some other way and it gets it converted into the electrical energy. That complete system is known as the generation system. So, based on type of raw energy or the source of energy, it uses the generation system is divided into two types. The first one is the conventional power plants and the second one is renewable energy based power plants.
We can see here the coal based or the coal energy based power plants are the conventional types of power plants. Same as the gas based which this gas we mean the natural gas or the CNG type petroleum gas. CNG means compressed natural gas. So, coal based, gas based, they are actually fossil fuel energy based power plants. That's why they are conventional power plants. Same as nuclear energy based power plants are also classified as conventional energy power plants. While on the other hand, the renewable energy power plants, they use hydropower in the rivers or the large reservoirs.
They use wind energy, they use solar energy or they use other type of renewable energy like tidal, geothermal or small hydroelectric power plants. So, in a way, the generation system can be divided into two broad categories based on the type of source energy they are using. Let's do that and see which ones are thinking. So, it's going to take these嗎? It's going to be the next item ready. So, it's going to take it to be a little if we can do anything. So, it's going to be the next item that we can do.
Now, going one by one with the type of and generation system, first we will discuss about the coal based power plant. So, the coal based power plant, they are also known as the thermal power plants. In the thermal power plant, the source of energy is coal or gas or any other petroleum. Basically, they work on the principle that they convert the chemical energy first into the mechanical energy and then into the electrical energy. The chemical energy stored in coal, oil or gas is transferred into electrical energy in thermal power plant.
The heat released by the combustion of coal produces steam in the boiler at high pressure and temperature, which when passed through the steam turbine gives off some of its internal energy as mechanical energy. The steam turbine acts as a prime mover and drives the electric generator or alternator. The generator is also known as alternator. A simple symmetric diagram of the thermal power plant is shown here. The efficiency of the overall conversion process is very poor and its maximum value is about 40 percent because of the high heat losses. This is all about the thermal power plants. Now, moving on to nuclear power plants. The nuclear power, actually, it is the immediate practical alternatives of large-scale thermal power plants or the thermal power generation.
Actually, in the present scenario, across the globe, most of the power requirements are fulfilled through thermal power plants only. As I have already discussed in the same in the session one that for almost all the countries, they produce for more than 50 percent of their electrical energy requirement through thermal power plants. But due to increased concern about the environmental pollution and depleting fossil fuels, we need to have some replacement for the thermal power plants. The renewable based energy like wind and solar, they can produce the electrical energy, but their capacity level is not as large as the thermal power plants.
So, the nuclear power generation produces an immediate alternative of large-scale thermal power plants. So, to generate the power at a single location in huge quantity, nuclear power can be a good alternative for the fossil fuel based power plants. The conversion of nuclear power plants. The conversion of nuclear power plants. The conversion process follows the same scheme as in thermal power plants, but here the source of energy is the nuclear fission process. While in the case of thermal power plant, the source of energy is the combustion of fossil fuel or the combustion of coal, petroleum or any other fossil fuel.
In nuclear power plant, the main part is reactor. We can see here the reactor is the main part. In this reactor, the nuclear fission reaction on uranium-235 takes place. There are moderators and control rods. The moderators, control rods and coolants and other are important parts of the reactor. In the heat exchanger or the steam generator, the high temperature and pressure steam generates, which run the coupled turbine generator system. So, in a way, the conversion process in the nuclear-based power plant, the source of energy is nuclear fission, from which the heat energy gets produced.
In this heat energy, the kinetic energy gets converted into the kinetic energy of the steam and the kinetic energy of the steam gets converted into the kinetic energy of the turbine and the generator system. Now, moving to the hydropower plants, in the hydropower plants, they are also large-scale power plant, but here the conversion process is slightly different. We should also keep in mind that hydroelectric power plants are the renewable energy-based power plant, which means it doesn't need any kind of fossil fuels or it doesn't pollute the environment.
It converts the potential energy of water into kinetic energy and then into electrical energy by utilizing the turbine-generator combination. It is one of the oldest and cheapest method, but the drawback with the hydroelectric power plant that it involves high capital costs and a long gestation period. Actually, for installing or for commissioning a hydroelectric power plant, we need to build a huge reservoir or a huge dam to store the water in the reservoir bank. So, that's why it takes a longer time and it takes a huge amount or huge capital cost for building these reservoirs.
Also, it involves the construction of generate alternator turbine and alternator combination. And then, it requires the construction of some transmission system to connect this remote generation system, hydroelectric power plant. So, all these construction takes huge time and it takes also huge cost. That's the drawback, but the running cost of this hydroelectric power plant is almost zero as it converts the kinetic energy in the flow of water into electrical energy. So, this kinetic energy is almost or it is actually free of cost. It is just because of the gravitational force of Earth.
Now, moving to other type of renewable energy, renewable energy based power plant. Here, it is wind farm. In the wind farm, the working principle is also same as the hydroelectric power plant. They convert the kinetic energy into the electrical energy, but the source of energy here is wind. In the hydroelectric power plant, the kinetic energy stored in the flowing water gets converted into electrical energy, but here in the wind farm, the kinetic energy stored in the flowing wind gets converted with the help of wind turbine into electrical energy.
In the wind farm, there is also one kind of energy, which has been described as like 59.3% of the total kinetic energy present in the wind can be exhausted or can be converted into electrical energy. So, with the help of wind turbine, we cannot convert more than this beds limit that is 59.3% of the total wind energy. But, it is considered as renewable energy based. So, whatever amount of energy we are getting through wind farm, it is absolutely free. Here, again, the installation cost is high, but it is not as much as the hydroelectric power plant, but the running cost is very low or it is almost zero cost in the running.
So, it is also considered as renewable because it is inexhaustible and non-polluting. But, the drawback with the wind farm is it is highly intermittent and So, I want to do this, I want to do this, I want to do this. And, but with that heat, you know, if there is a energy system, you know, it is not going to be local energy. Unpredictable. With the electrical energy, we want reliable and the continuous production of electrical energy because at the demand side also, the loads are also continuously connected.
So, the power requirement is also continuous but with the wind farm, we cannot rely on only wind farms because the wind energy may be present in night time but it may not be present in day time or it may be present in some particular months of the year but it may not be present or it may be present at low value in some other months of the year. That's the main reason the wind farm is not that popular. Now, moving to the solar energy, the solar energy, they converts the solar energy into electrical energy. So, the solar energy based power plant, they are also considered as renewable energy based power plant.
Here, here two types of energy based power plant. Here, two types of energy conversion are in practice. One is direct conversion into electrical energy using photovoltaic panels. Here, we can see there are some photovoltaic panels or TV panels which are made of silicon or germanium. Here, we can see there are some photovoltaic panels. That's why too we need to convert into alternating current. So with the help of inverter we convert into the alternating current and then with the help of distribution board and transformer we can feed it to the distribution system or we can feed it to the distribution level feeders.
Here to monitor or to control all these equipments we need to have one monitoring system also. That's why the photovoltaic based energy conversion may be bit costly but in terms of power production this cost is not that sufficient or it's not that significant. In the same way the other type of energy conversion they also use the solar radiation but here they use directly solar radiation to convert to utilize the heat energy from the solar radiation. With the help of some insulating pipes they convert the water into high pressure and temperature steam and this high pressure and temperature steam passes through the turbine and generator system.
At this stage it looks similar to the other type of power plant like thermal power plant or the nuclear power plant but in the thermal or the nuclear power plant the primary energy source is some fossil fuel or the nuclear fission reaction which generates the heat energy to generate the steam. But in case of solar energy based power plant the solar radiation but in case of solar energy based power plant the solar radiation or the heat from the solar radiation is used to convert to generate the steam from the water.
So this is all about the solar energy based power plant. So we have discussed about the generation system the type of conventional and non-conventional generation we have discussed or we have gone through some technical aspect of some a few non-conventional energy non-conventional energy based power plant like thermal and nuclear. And we have also gone through some renewable energy based power plants like hydroelectric wind and solar. Now let's have a techno-economical comparison of these type of power plants. As I have already told that the PV system or the photovoltaic system at a small scale is cost effective and it is very competitive approach with other type of technologies.
The solar photovoltaic produces the least cost per kilowatt hour among the other energy supply system. With the least cost per kilowatt hour I mean that the cost required to produce one unit of energy. So with solar photovoltaic that cost is minimum. In hydroelectric system it has highest initial cost or it has the highest capital cost or the installation cost. As I have already discussed the running cost of the coal based power plant are significantly more than any other type of the power plant. As we know that the coal based power plant the primary source of energy is coal.
So to transport the coal from coal mine to the generating station they need some transportation cost. And the cost of the coal is also getting increased day by day. That's why the running cost of this type of power plant is significantly more. The risk of nuclear leakage also. So with the case of nuclear energy based power plant they have to make the nuclear energy based power plant at some very remote location. Or it should be very far from the population density. So because there are some risks associated with the nuclear energy based power plants.
That's why its operation cost or its installation cost is also very high. So this is the techno economic comparison for the different types of power plants. So here we have done discussion with the generation system. Now we can move on to the transmission system. So moving to the transmission system. From transmission system actually it is a medium to transmit the electrical power from generating stations to node. It is made up of conductors with different configuration for different voltage levels and distances. Actually from generating stations to the end users we need to have some conductors to transmit the electrical power.
To fulfill this purpose the transmission system is utilized. The voltage level of the transmission network in India are also varied. So from 66kV to 765kV we use the voltage level in India. Here 66kV, 110kV, 132kV, 220kV, 400kV and 765kV are used in India as the voltage level. These voltage levels are in accordance with the regulation and standards of some organizations in India. In India there is Central Electricity Authority , Central Electricity Regulatory Commission , State Electricity Regulatory Commission . So these are the organizations or these are the government bodies which regulate or which fix the standards for all the electrical operations in India.
Now not only the voltage levels, they also fix the standards for various other things like frequency level, current and any other parameter associated with power system or the electrical system. Okay now this is an important question which every student or every student in electrical engineering comes in mind that why the transmission voltage is 11kV or 33kV or 63kV or 132kV. So here you would like to ask your question, why this protection would require a lot of criticism of the current borders line? Here I want to clarify that actually that in the transmission system the conductors are made up of aluminium or some alloys of aluminium.
They have some resistances and because of these resistances when the power flow through this transmission line there are some voltage drop. So, this voltage drop is not fixed and it depends upon the type of conductor and the length of the line but approximately it is taken as the 10% of the voltage gets dropped from sending end to receiving end. So, to compensate for this extra or to compensate for this voltage drop 10% of the voltage drop we send extra 10% voltage from the sending end. So, from example we can see if we want to get 10kV at the receiving end voltage so the sending end voltage should be 10kV and the 10% of the 10kV so it becomes 11kV that's why So, if we want to receive 10kV at the receiving end the sending end voltage should be 11kV similarly we can see the 22kV, 33kV, 66kV or 132kV voltage levels are used at the sending end.
And 132kV is because here at the receiving end we want 120kV of the voltage level now we understood that while voltage level is fixed at these 11, 33, 66kV or 132kV but these voltage levels are fixed for these values because at the low voltage level the 10% voltage drop happens but for the high voltage transmission the voltage drop is compensated by the reactive power compensators so that's why the voltage level like 400kV or 765kV we don't use this 10% criteria there The voltage levels of the voltage at the transmission will decide based on this criteria it has I want to also clarify one thing here that most of us have in our mind that the form factor plays a role here in defining the transmission voltage But deciding the voltage level does not depend on form factor in any way this is a common myth popular among most of us So now moving further the types of transmission system as we all know that transmission system is the conductors and they are used to transmit electrical energy from generating stations to the end users or the distribution side But depending upon the length of transmission line or depending upon the voltage level we divide the transmission system into three categories or in three types First one is long long transmission line for long line the voltage level is around 132kV If the voltage level is around 132kV or if the voltage level is around 132kV or if the voltage level is around 132kV and the line length is around 240kV Then it is classified as long transmission system Here in the power system modeling here in the power system modeling the long transmission line are represented by 4 parameters 4 parameters resistances, inductances, capacitances and conductances So all the 4 basic parameters for a conductor are included in the modeling of long transmission line While the second type of transmission line while the second type of transmission line is medium transmission line In medium length transmission line the voltage level if it is 33kV and 132kV So if the voltage level is in between 33kV to 132kV and the length of line is in between 80kV to 240kV then it is classified as medium transmission line In the medium transmission line the capacitance is considered as lumped at one point In the modeling of medium transmission line it uses pi model and the t model All these modeling we will discuss in detail all these modeling we will discuss in detail in our further modules So now moving to the short transmission line if the voltage level is less than 33kV and line length is also less than 80km Then it is classified as short transmission line The effect of capacitance is ignored here It is represented by only resistances and inductances Here the short transmission line are simply modeled with the help of only a resistance and inductance Here the shunt branch which includes capacitance and the conductance are completely ignored While they are included for long and the medium transmission line So this is the type of transmission system Here we have seen the long, medium and short transmission line How they are classified and how they are being modeled while doing any power system simulation on any software platform So this is all about the transmission system Now we will move towards the distribution system This is the end of session 2 In the session 2 In the session 2 we have gone some deep in the technical aspect of the power system We have seen that the power system has 3 main components Generation, transmission and distribution We have gone the technical detailing of different type of generating power plants Like thermal power plant, nuclear energy based power plant, hydroelectric based power plant, wind farm and solar energy based power plant After that we have discussed the transmission system The voltage level, how they are decided at the transmission system And the type of transmission system So now in the next session we will discuss about the distribution system And the power system simulation tools Also simulation software The power system studies So all these things we will discuss in the next session So here this is all for the session 2 In this session 2 I'll see you next time.