Lesson finished
Unlock all 33 lessons of Introduction to Cellular Communications 2G-3GFull course ₹40,000 · paid
dBm Power, Base Station Types, Coverage and Mobile Call Flow
A free lesson from Skill-Lync's Introduction to Cellular Communications 2G-3G course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “Week 1 Session 2”
What will you learn in this free Introduction to Cellular Communications 2G-3G lesson?
The instructor explains dBm and its conversion to watts, then compares macro, micro, pico and femto base station power. He covers antenna lobes, tilt, sectors and hexagonal cells, microwave antenna size, the SIM and mobile station, initial attach, and a call from a phone to a landline.
- dBm and watt conversion formulas
- Macro, micro, pico and femto cell power limits
- Antenna lobes, tilt, sectors and hexagon cells
- Initial attach and call flow to a PSTN number
What comes after lesson 3?
Later in Skill-Lync's Introduction to Cellular Communications 2G-3G course (paid): lesson 4, Week 1 Session 3; lesson 5, Week 1 Session 4; lesson 6, Week 1 Session 5. The full course has 33 lessons (13 h 14 min of video); see the course overview or its price and syllabus.
Lesson transcript
Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.
Alright, so let us understand the power calculations. Now, the power calculation is very simple. The conversion of dBm, that is dB milliwatts, is 0 dB is equal to 1 milliwatt of power. So, we can think of it as dB is a ratio of power, while dBm is ratio of power, where power is in milliwatts. So, it would be x and py. So, the conversion is as follows. dBm is 10 log milliwatt of power. And, if we take power for a macro base station, that is 46 dBm. So, the power is 1040 watts. And, when we convert it into milliwatt, it would be 40 into 10 to the power 3, which will come to 46 dBm.
Similarly, the calculation for dBm to watt, would be 10 to the power dBm minus 30 divided by 10. So, suppose the power is 46 dBm. If we want to convert it into watt, we can just use this formula. 10 to the power is 10 to the power 46, minus 30 divided by 10, which will be 10 to the power 1.6. And, it is approximately 39.8 dBm. So, it is actually the conversion from dBm to watt and watt to dBm. So, you should always know the scale of dBm or dB, dBd, dBi, when we are talking of the terms related to RF or antennas.
So, as mentioned, the macro cell base station does not have any upper limit. But, typically, it is 46 dBm to 49 dBm. And, it is governed by the local regulation. Micro cell is 38 dBm. Pico cell is 24 dBm. And, famto cell is 20 dBm. Now, let us understand the coverage of a base station. Now, whenever there is an antenna. So, this is a directional antenna. So, in this directional antenna, it has a main lobe. So, this one is your main lobe. Let me show you here.
So, this is your main lobe. And, you will have some side lobes here. You will have some back lobe here. So, this is the, you can see the radiation pattern of antenna. So, this is the radiation pattern. And, the main lobe is what which needs to serve the population. So, to serve the population, the usual height of a tower is 30 meters. For this, this is a ground-based tower, GBT. We will have a rooftop tower, RTT. Or, we have some tower masts. So, usual, the height is 30 meters.
So, to serve the population, we need to have some down tilt. That is, we need to align the antenna to serve the local, you can see, the coverage area. Now, the tilt can be provided in two ways. We have mechanical tilt and electrical tilt. So, this is the mechanical tilt that we have shown here. All right. And, the electrical tilt works in the way that it will direct the beam downwards. All right. Rather than, you know, changing the, you can say, alignment of the antenna. Now, usually, if you are near the antenna, you will have full coverage displayed on your mobile phone. And, if you go away from the antenna, towards the edge of the cell, you will receive this kind of signal, which will show you that the signal signal is degraded.
Now, this is the cell edge, which is typically minus 120 dBm. And, you can see, it is 1 to the power. It is 15. So, we have 15 almost zeros here. So, 0.00 up to 15 zeros and 1 watt. So, this is a very low sensitivity. But, the base station antenna is able to, you can say, hear the power in this range as well. So, the coverage depends on the Rx sensitivity of the MS. That is, at the cell edge, where the MS or the mobile station is able to hear the antenna as well as antenna is able to hear the mobile station. Now, it is up to minus 120 dBm for the MS as well. So, the coverage planning is done by the link budget calculation. So, the link budget calculation is done to plan the, you can say, various losses and to account for the gains and decide what is the actual sector coverage.
Now, let us understand the sector coverage. Usually, to provide a 360 degree coverage, we have what we call directional antenna. And, the directional antenna can serve area of, at most, 120 degrees or 150 degrees. But, to serve a complete 360 degree in data, you need a minimum of three sectors. That is, one sector will serve 120 degree. So, this is the, you can say, approximate coverage area shown by a hexagon. Why hexagon? Why hexagon? Let me explain you with a whiteboard. All right. So, the question is, why we are using hexagon? So, when we are doing a cellular network planning, all right, now, we can use to denote a 360 degree coverage using a circle.
So, this is the, you can say, the actual coverage area of a site. We will have the site in the center and the coverage area is denoted by a circle. But, while doing the planning, we have to, you know, if we are using circles here, there would be some overlap for the planning and we don't want this overlapping due to planning. So, geometrically, this circle is not an efficient space. You can say, efficient shape. Now, if we do not use overlapping, there would be some void spaces.
So, geometrically speaking, circle is not an efficient shape to avoid any overlapping or void spaces. Now, the second geometry that we can use is squares. So, the second geometry that we can use is squares, but square does not have, from the center, the distance is not uniform. Like, if we see a square or rectangle, the distance of this edge, x would be always greater than y. Okay. So, it does not denote a good geometrical shape where the coverage is mapped consistently. So, the efficient space is a hexagon. Now, with hexagon, mostly, you will have with the edges, so these edges would be equally shaped and this coverage area can be, you know, planned without any overlapping or void area.
So, that is why geometrically, we call it geometrically hexagon is an efficient shape to denote a coverage area of 360 degrees. So, this is our coverage area and mostly what's happening, you have antenna serving each coverage area. So, this is your antenna and in each coverage area, you will have a remote radio head. So, each sector, we call it sector. So, each sector will have a separate remote radio head. Now, we can do one more thing. We can go for sectorization. Like, I can just sectorize it more and I can use six antennas of 60 degree each to serve 360 degree.
Or maybe, I can just sectorize this sector and I can have 60 degree here and 60 degree here and I can use 120 degree here and 120 degree here. So, you can go for sectorization based on the capacity and coverage requirements. So, sectorization is an efficient way to increase the capacity. So, you can increase the capacity of a coverage area with minimizing the interference. So, the complete coverage is achieved in the form of three sectors, 120 degrees each and further sectorization can be done of six sectors or 60 degrees and each sector will have generally its own transmitting antenna.
And configuration and remote radio engine. So this is how a complete 360 degree coverage is served by a base station site. So now let us understand what is microwave transmission. So microwave is a line of sight communication. And it's mostly used for transmission network. We call it transmission network. And it is a layer 2 transmission. If we go by the OSI model, just like your Ethernet. And what's happening here, we are using two directional antennas in the range of 1 to 60 gigahertz, which work on the line of sight and point to point.
These antennas are short, medium and long haul. And they serve frequency up to 1 to 60 gigahertz. So now what's happening here? This is your transmitting antenna. This is your kind of a repeater, repeater site. So what this antenna will receive, mostly the TX and RX antenna will be of same size because they will be serving a specific frequency. And it depends on the frequency. Now, what this RX antenna, the signal will go to the baseband. So this baseband is serving microwaves. Now, the baseband, what it will do? Suppose the frequency here is 15 gigahertz.
And this frequency is 10 gigahertz. So it will just transmit. You can say receive the signal from 15 gigahertz signal and transmit it on 10 gigahertz signal on this different antenna. And it will process the signal as well. So this is a function of a repeater. So it's just taking. It's kind of a relay. It will take the messages and it will transmit on the different frequency. So this is how microwave transmission works on based on the various repeaters and this distance depend on the, you can say the frequency.
So high frequency will have lower distance and low frequency can travel to the greater, you can say, greater range. So this is basically depending upon the wavelength. So lambda is 1 by F. So if we have high frequencies, if the frequency is up high, so range is low, if frequency is low, the range is high. So let us understand what type of antenna we use in microwave. So the antenna is directly related to the type of frequencies. So high frequency, we will use smaller antenna. And this is because we have the antenna size of lambda by 2.
So lambda is, you can say lambda is equal to 1 by F. So antenna, you can, if you study the dipole antenna, you will understand it is basically lambda by 2. And if we increase the, you can say frequency, like for 25 gigahertz, the antenna size is very small and 10.5 gigahertz is around 0.6 meter. 25 gigahertz is 0.3 meter and 5 gigahertz is 1.2 meter and 2 gigahertz is 3.7 meter. So this is the, or you can say the size of antenna that we are using for microwave.
And this is directional. So if you see your DTH service, you have a small antenna. So you can just relate to it. The smaller antenna will be working on higher frequency. You can just find out what frequency your DTH is working on. And it will, just to give you an idea, it is working on a KU band, which lies somewhere around 20 to 30 gigahertz. So you can relate, your antenna size should be around 0.3 meters. So let us go to the components of mobile station.
All right. So let us try to understand what are the components of the MS mobile station. So mobile station contains two modules, that is mobile terminal and SIM, the subscriber identity module. So all of you know about this, you have your phone, which actually you call your mobile device or the mobile terminal. You insert a SIM card, that is the subscriber identity module. So now this SIM card is pre-programmed. So this is pre-programmed and it contains the following details. The MC or International Mobile Subscriber Identity.
It contains an authentication key, KI and location area identity. Now, the composition of these two, mobile terminal and SIM is called a mobile station. Until or unless you have a SIM card in your phone, or that is these three components, MC, authentication key and location area identity, you won't be able to use your mobile phones. Some mobile phones are pre-fabricated with this information inside the mobile terminal, so that wherever the operators are supplying the mobile devices, but it contains an inbuilt SIM card as well. So let us understand what happens when you switch your phone on or turn on your phone.
As soon as you insert the SIM card, you have a procedure that is called initial attach. So in initial attach, what's happening, your mobile station will try to find out the network and will try to connect to it. So MS listens to all the broadcast signals from the neighboring base station. So all the base stations, or the radio base stations, or the mobile sites, are transmitting continuously some broadcast information. So it is just like when you are trying to tune into your FM radio, you are scrolling through various frequencies, right?
So the mobile station will scroll through various options. So FM is frequency modulated, but based on the modulation, like whether it is TDM or FDM or CDM, we will see what these are in the later slides. So based on the configuration, it will try to tune in to those, you can say information, and try to decipher the broadcast information of the neighboring sites to find out which site is the one which is serving the details as mentioned in the SIM card. So it selects the desired network based on the information in the SIM.
So we have the PLMN, that is the public land mobile network. So PLMN is the composition of three things, that is MCC, mobile country code, and then the MNC digits, which specifies what are the number of digits in the MNC. So it can be two or three. So like in India, you can have 40433 and you can say your detail or you can say the PLMN code of a mobile. Where MCC is 404 and MNC is 033. So it will try to find out the base station which is broadcasting the information with the PLMN which is mentioned in the SIM card and it will camp to the base station.
So these are the base stations which are transmitting and suppose in initial attach, the SIM card is of this network, it will try to camp to the base station. Then you have, during initial attach, you have the procedure called random access. So the problem with the shared medium, whenever you are studying networking, the key important problem of a medium which is shared by end users is that how those end users will access the medium. And there are multiple solutions to it and one of them is random access.
So random access means the user or any terminal will access the network randomly and unless it receives the information from the network, it will keep on trying after holding off some timer. So random access procedure means the mobile will try to connect to the network and MS will send an access request on the random access channel. So we have a specified channel for random access and the network will, you know, response with the information of the dedicated channel. So this channel can be different based on the technology.
So you can say it is the response or acknowledgement of the dedicated radio channel. Then the next procedure is for authentication. So MS will go ahead for authentication. So authentication means network will try to ensure that the mobile station is a genuine mobile station which is allowed to connect to the network. So it will try to go ahead with the authentication. Now let us understand what happens when we have the authentication process. So during the authentication, we have a database in the network which will contain the information and based on that, the authentication will be performed.
So MS will send, the mobile station will send the MC. It will send its MC. That is the international mobile subscriber identity. Now core network will calculate an SRS which will be using a function A3 where the key KI and a random generated keyword would be used. So we have a function A3 which will have two inputs KI and random and using that SRS would be generated. So this SRS will be sent with RAND. So the two things that is SRS and RAND would be sent to the network.
So now this SRS is kept at the core network only and RAND is sent to the UE or the mobile station. So now the mobile station will calculate using the same function A3 and KI based on the same and the RAND provided by the network. So let us call it SRS, let us call it SRS dash. Alright. So and it will send it to the core network. Now the MSC or mobile switching center would compare SRS dash and SRS. If both are OK or both are equal, then the authentication is successful.
So the core network. So the core network compares SRS. So this is a very simple procedure of you can say authentication. Now you can see here the mobile station will send MC and SRS is generated and RAND is shared to the mobile station. Now mobile station. Now mobile station will calculate you can say response that is using the same function with KI and the random message that has been response random keyword that has been received from the network and it will share it to the core network and then the core network will compare SRS and RES and then we have the security mode complete command.
So this authentication will keep on happening whenever you are trying to access the network after some time. So there is a specified you can say timer and after what or you can say you have to have the security mode. There is a timer in the network which specifies after that timer the security mode process would be followed by the network to keep on identifying and authenticating the mobile stations. So once the security mode is complete, you will see the network and you are actually attached to the network.
So now let us understand how the call flow would work. So this is a very generic scenario. You have your mobile now authenticated with the network. It has a signal. Now suppose you are calling a landline number. We have a landline number. Suppose the number is 0 1 1 2 3 2 3 2 3 2 3. So this is your PSTN number. So the PSTN is the traditional number that we are using. So you are ready to receive and dial a call. All right. And however, in the background, there would be some signaling messaging that will be keep on going between the network and the mobile phone.
Now as soon as you dial this number on your keypad and press the call button, what will happen? So first of all, you would be provided a dedicated channel. So how it will be done? So first of all, as soon as you dial the MSISDN, we call it the MSISDN or the PSTN number. So this is mobile station ISDN number. Okay. So the RAND or the radio access network will send the details to the core network. Now you are still not be provided a dedicated channel, but you suppose access the network and the information is passed to the RAND network.
So the RAND network will send it to the core network, the details. The core network will check if the MSISDN is allowed to perform the call. So it will check the policy function that if the mobile station is allowed to perform the call. And if yes, it will ask the RAND to allocate a dedicated channel. So your radio access network will grant you a dedicated channel. So the MSC will allow the call to GMSC. All right. So GMSC is the gateway MSC, which is connecting to the PSTN network and GMSC routes the call to the local exchange.
So it will send it to the exchange wherever the exchange is located. So suppose the number specifies the exchange or you can see that the circle is Delhi. So it will pass on, you can see the information to the exchange of Delhi. And then it will send a ring back tone, ring back tone or you can see the dialing tone that you hear when you are trying to connect to someone. And as soon as the person picks up the call, the complete circuit is granted to you from the wireless as well as towards the PSTN for you to have the conversation.
So this is a very high level overview of how your mobile phone works. By end of this course, you would be specifying the third generation, how various type of mobile phone functions are signaling or calls would happen. And what are the various procedures to that is performed by the XAN network as well as the core network to ensure the mobile network is interference free. The mobile user is able to use the services in the best possible manner without any interruption. So let us go ahead and understand what are the key takeaways by this section.
So the key takeaways from the first section is that a mobile network comprises of the core distribution or the access network. And the electromagnetic waves are mostly used in telecom, which are from the RF spectrum and microwave spectrum. From the RF spectrum, we are using in the omnidirectional use case, that is for the providing the access to the user. And microwave spectrum, we are mostly using for the transmission. A base station comprises of components such as antenna, remote radio head, connectors, SIPRI, that is a common public radio interface, or feeder, which is used to connect the remote radio head, or the radio head towards the antenna, and the base band.
Now, transport network provides the connection between radio and core, which works as a distribution layer. And the mobile station comprises of the mobile terminal and the SIN. So all these components work to provide the mobile user complete services that are being assigned by the operator. So after this, we'll start the next section, that is wireless communication fundamentals.