← Previous lessonFree lesson 3 of 3 · lesson 3 of 50

Unlock all 50 lessons of Foundations of Thermodynamics and its Industrial ApplicationsFull course ₹40,000 · paid

Price & syllabus
Free lesson · 16 min · no payment

Ideal Gas Law, Gas Constant and Ideal Gas Processes with Examples

A free lesson from Skill-Lync's Foundations of Thermodynamics and its Industrial Applications course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “Week 1 Session 3”

What will you learn in this free Foundations of Thermodynamics and its Industrial Applications lesson?

The instructor defines the ideal gas model and the two conditions under which it works, low density and temperature well above condensation. The lesson derives PV = nRT and PV = mRT, then describes isothermal, isobaric and isochoric processes on PV diagrams, with worked problems that require absolute temperature in Kelvin.

  • When a real gas can be modelled as an ideal gas
  • Ideal gas law in mole, mass and flow rate forms
  • Isothermal, isobaric and isochoric processes
  • Why temperature must be in Kelvin in gas calculations

What comes after lesson 3?

Later in Skill-Lync's Foundations of Thermodynamics and its Industrial Applications course (paid): lesson 4, Week 1 Session 4; lesson 5, Week 2 Session 1; lesson 6, Week 2 Session 2. The full course has 50 lessons (17 h 34 min of video); see the course overview or its price and syllabus.

Lesson transcript

Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.

Welcome back to Thermodynamics and its industry application. We will continue week one microscopic description of matter and we will begin session three. To start session three, we'll be discussing about ideal gas. What is an ideal gas? An ideal gas is a model that ignores the interactions between atoms in a microscopic system. The gas, the ideal gas are randomly moving atoms that bounce off of each other in the wall around their container or such an invisible volume. Basically, ideal gas is somewhat the simplification of real gas and it has shown in experimental to be quite good in modeling real gases if two conditions are met.

The first condition is when the density is low. That means that very few atoms occupy the volume. Therefore, you have very little interactions between atoms. The second condition is that the temperature is well above condensation point. So it's just not enough to be at a gas state, but you can't be close to where you're at the point where you're condensating or even at a liquid or solid state. So if you're far away from that condensation point, then that gas itself can be modeled as an ideal gas. So even water can be modeled as an ideal gas if it meets these two conditions.

If the density gets too high or if the temperature gets too low, then the interaction forces between each matter, between each molecules or atoms will start to play a role in the behavior of the gas. Earlier, we introduced the idea of state variables. State variables will be considered an ideal gases or a microscopic system. The state variable for an ideal gas are volume, the number of moles, the temperature, and the pressure of the gas. These four state variables are not independent of each other. When you change one, the others will change as well.

As one variable change, the relationship between the other variables, such as as the temperature change, the pressure and the volume change linearly with respect to the temperature at a constant slope. Based on this relationship, we can denote that the behavior of the state variable for an ideal gas can be modeled in such a way that pressure times volume is equal to the number of moles times the temperature. Experiments that were done in the 17th and 1800s found a very special relationship between all four of these states.

Suppose you change the state of gas by heating it or compressing it, doing something else to it, and measuring pressure, volume, number of moles, and the temperature, and repeating the process over and over again. This created a slope which shows the relationship and brought the idea of ideal gas laws. Here, the relationship between the slope is shown to be 8.31, which represents joules per mole per Kelvin, and is now known as the universal gas constant. Another way to write the ideal gas is simply using mass, which is PV equals to MRT.

Here, R is the universal gas constant divided by the molar mass, and the units for that is kilojoules per kilogram per Kelvin, or kilopascals times meter cubic per kilogram. Here, you can also write the ideal gas in terms of flow rate, where the pressure times the volumetric flow rate is equal to the mass flow rate times R times T. And once again, R represents the universal gas constant divided by the molar mass. And if you consider an ideal gas in a sealed container, you can state that the pressure times the volume divided by the temperature at the initial state variable is equal to the pressure times the volume divided by the temperature at the final state variable.

Here, you can see a model in representing a real gas and an ideal gas on the right of the slides. Here, you can see that it ignores the interaction forces between each molecules, but on the right for real gas, there is interactions between each molecules for real gas. To better understand what we just reviewed, I will provide you an example problem. Let's say a cylinder of a gas that is at zero degrees Celsius. A piston compresses the gas to half of its original volume and three times of its original pressure.

What is the final gas temperature? So, note all the information that they gave us. They told us that the initial temperature is zero degrees Celsius. They told us that the gas is being compressed within the piston. So, that means it's almost like a sealed container. And that from one state variable to another drops by half of the volume and it becomes three times strong in pressure. The goal is to find the final temperature. So, what we're going to do is treat this gas as an ideal gas in a sealed container.

From there, we know that if we take the equation that was previously shown in the slide before, you will see that the temperature, the final temperature, is just equal to the initial temperature times the final pressure times the final volume divided by the initial pressure divided by the volume. But we have no idea, and we have no idea what the final volume is, nor do we know what the initial pressure is or the initial volume. Well, you don't need to know the initial pressure, initial volume, final volume, or final pressure.

We could simply use the relationship between the initial state variable and the final state variable. So, as expressed in the problem, the piston compressed the gas to half of its volume and increased the pressure three times. The initial temperature starts at zero degrees Celsius. Now, remember when we talked about Celsius? Because Celsius is not an absolute scale, we cannot use Celsius in our ideal gas. The relationship of an ideal gas has to be in an absolute scale, and pressure also has to be in an absolute scale.

Therefore, the first step is to convert your initial temperature from Celsius to Kelvin. Now, zero degrees Celsius is equal to 273 Kelvin. Once we have that, then we can rewrite our equation. Here, our final temperature will equal to 273 Kelvin times three times the pressure and one-half the volume, which equals to 409 Kelvin, or 136 degrees Celsius. Now, what if we had used zero degrees Celsius? Well, if we had used zero degrees Celsius in our equation, then our final temperature would have still been zero degrees Celsius.

Now, does that make any sense? No, it doesn't make sense. Remember what I stated earlier. When you change one parameter in a state variable, all the other parameters and all the other properties change as well. So, you cannot have the same temperature, initial and final condition, when both volume and pressure is changing. Now, unless they change corresponding such that it obeys the ideal gas law, for example, it could have been one-half the volume, and then it could have been twice the pressure, then you can end up with the same temperature.

But this is not the case. Reiterating, we did not need to know the actual volume of the pressure or volume, just the ratio by which they change. In a lot of thermodynamics problems, you are not given all the information, and all the information are arbitrary. What's important is the relationship between one state to another, and the path that it takes to achieve such state. Next, we'll discuss ideal gas process. So, what is an ideal gas process? It's when an equilibrium state undergoes a change from one state to another.

In this case, an ideal gas process is when a gas changes from one state to another. It is useful to think of an ideal gas process in terms of a PV diagram. A PV diagram is a pressure versus volume graph that shows the relationship of one state to another state in terms of pressure and volume as it changes. But knowing the pressure and volume, and assuming that the mass in the container is sealed, you can find what the temperature is at any point in a state variable.

Examples of ideal gas processes are isochoric, which represents constant volume. This means that the final and initial state variables have the same volume and do not change. But all the other parameters and L state variables can change. Another ideal gas process. Another example of an ideal gas process is an isothermal process. An isothermal process is when the initial and final temperature are equal to each other. In this process, the pressure times the volume will always equal to the pressure times the volume of the initial and final state together.

This is derived through the ideal gas law. So how does one generate an isothermal process? Well, one can generate an isothermal process by moving the state so slowly that the temperature is almost equal to the surrounding throughout the whole entire process. Another ideal gas process can be considered as an isobaric process where the initial and final temperature are equal. An example of this process is when you have a mass on top of a piston full of gas and you change the temperature of the gas by heating the air in the piston.

The mass is frictionless in the piston such that the volume moves up and down, keeping the pressure the same the whole entire time. This is what's known as maintaining a mechanical equilibrium. On the right, it shows how each behavior change correspondingly to what's listed on the left. The first picture represents an isochoric constant volume process. Here, the pressure goes increases from state one to state two while the volume does not change. In the middle of the graph for the PV diagram, you can see an isothermal process where both pressure and volume changes, but they change in such a way that if you multiply the pressure times the volume, you'll end up getting the same as state one and state two.

The next PV graph shows the process of an isobaric process. Here, the pressure remains constant and the volume changes from state one to state two. Here's another example problem to help illustrate what was discussed about ideal gas process. The constant volume is placed in contact with a reference cell containing water at a triple point. After reaching equilibrium, the gas pressure is recorded as 55.78 kilopascals. The thermometer is then placed in constant with a sample of unknown temperature. After the thermometer reaches a new equilibrium, the gas pressure is 65.12 kilopascals.

What is the temperature of this sample? So a lot of information was given in this slide. One key focus is to note that this is a constant volume gas thermometer. Another key point is that at equilibrium from one state, the pressure is recorded at 55.78 kilopascals. Another key information to note is that the final pressure is 65.12 kilopascals. The goal is to find the temperature of this sample. So the thermometer volume doesn't change. That's what it means to be isochoric, or in this case, constant volume. The temperature is at the triple point of water, which is T1 equals to 0.01 degrees Celsius, or 273.16 Kelvin.

The ideal gas law for a closed system is pressure times volume divided by temperature of one state is equal to pressure times volume divided by temperature of another state. The volume does not change. So V2 divided by V1 is equal to 1. So putting everything together, we can say that the final temperature is equal to the initial temperature times the ratio of the volume times the ratio of the pressure, which is also equal to the temperature times 1, which is the ratio of the volume times the ratio of the pressure.

As you can see, as you can see, when we take the final divided by the initial pressure times the temperature, we end up getting 318.90 Kelvin, or in this case, 45.75 degrees Celsius. The temperature must be in Kelvin to do this calculation. Although it is common to convert the final answer to Celsius, the fact that the pressure were given to four significant figures justified using the notation that Kelvin is equal to Celsius plus 273.15 degrees. Rather than the usual 273.15 that the final temperature is greater than the initial temperature, which is expected when the pressure is increased.

Next, we'll talk about compressibility factor. But this concludes session three for week one, Microscopic Description of Matter in the course, Thermodynamics Industry Application. Stay tuned for session four.

Want the rest of Foundations of Thermodynamics and its Industrial Applications?

Get the full course syllabus and fees.

The full course is paid (₹40,000). We'll send the syllabus and call you back within one working day.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Full course · paid

Unlock the full Foundations of Thermodynamics and its Industrial Applications course

The remaining 47 lessons, mentor-reviewed projects and a certificate come with the paid course (₹40,000). Leave your details: we'll send the syllabus and fees and call you back.

Get the syllabus and fees

A counsellor calls you back within one working day.

By submitting you agree to our Terms and Privacy Policy.

Grow by Skill-Lync · free lesson

Start watching

Free, no payment. Leave your details once and every free lesson on Grow plays straight away. A Skill-Lync counsellor may call you about the full Foundations of Thermodynamics and its Industrial Applications course.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.