Lesson finished
Unlock all 59 lessons of Analysis and Design of Industrial Structures using STAAD.ProFull course ₹40,000 · paid
Steel Shapes, Built-Up Sections and the Stress-Strain Curve
A free lesson from Skill-Lync's Analysis and Design of Industrial Structures using STAAD.Pro course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “Introduction to Industrial Structures”
What will you learn in this free Analysis and Design of Industrial Structures using STAAD.Pro lesson?
The instructor describes hot-rolled sections (ISMB, ISWB, ISHB, channels, angles) and built-up sections such as plate girders and crane runway girders, including which part of an I section carries shear and bending. The second half defines stress and strain and describes the universal testing machine tension test used to plot the stress-strain curve.
- Hot-rolled Indian section designations
- Web carries shear, flange carries bending
- Built-up sections and crane runway girders
- Tension test setup for the stress-strain curve
What comes after lesson 3?
Later in Skill-Lync's Analysis and Design of Industrial Structures using STAAD.Pro course (paid): lesson 4, Understanding Stress-Strain Curves and Material Behavior; lesson 5, Introduction to Industrial Structures using STAAD.Pro; lesson 6, Types of Industrial Structures and Their Configurations. The full course has 59 lessons (27 h 53 min of video); see the course overview or its price and syllabus.
Lesson transcript
Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.
Hello all, in continuation to what we have seen in last session, this is session 2 of first week's content introduction to industrial structure. So now we are going to see the steel shapes and other properties of the steel and the behavior of the steel. Last week we have seen advantages, disadvantages of the steel and then what are the different compositions of the steel and what are the different standard steels that is available in market. So starting off with this week's, I mean this session's content, first we see what are the steel shapes that we use normally in industrial structures.
These are the hot rolled shapes which are the standardized rolled shapes. Hot rolled shapes are those shapes which are produced by hot rolled method. There is basically two types of method in manufacturing the steel. One is hot rolled, another one is coal formed. In hot rolled, we can get a thickness of the web and the flange will be comparatively more than the coal formed process. This coal formed process is a process where we make a thin sheets of members, very thin members like perlins which we use it normally as a coal formed members in some industrial structures, we use it those kind of sections.
Here the hot rolled sections, standard hot rolled shapes are the I section, T shapes and the angle section. What we see is normally in India, we call it as ISMB, ISWB, ISJB sections. IS is Indian standard, IMB is medium beam and then ISWB is wide flanged and ISJB is junior beam. So normally we use ISMB and ISLB section used as a floor girders, whereas ISHB are heavy sections which we use it for columns also. ISJB mostly don't use it, whereas ISWB is wide flanged where the width of flange is more and then it has more moment of inertia and more concentration along we have IYY plane which is a minor axis plane.
What we see from the drawing is we have a first one is this is I section which is conversion I shape section. In Britain you call it as a universal beam or universal columns, UC section or UB sections and in Europe it is called as IP section, HE, HL, HD sections where HE is also like beam section, HL is column section, HD is extra width section. In Europe it is called as wide flanged WF for H sections. So, HSS is a hollow square sections, similarly if it is circular we have a hollow circular cube section, this channel section where we have a shear center away from the center of gravity, it is outside.
A shear center is nothing but a point if we apply a load twisting can happen, hence channel section which is open section is not recommended where the unsymmetrical loading is expected to occur. So, these are different types of sections which you must be aware of it which you will be using in composition or in composite mixing with another section or combining different sections so that we increase the moment of inertia and then we increase the radius of gyration or slenderness ratio. So, these are some of the technical terms which you have come across already what is the moment of inertia or the radius of gyration on the slenderness ratio.
As a slight recap we will see in the future slides. Coming in continuation to what sections we have seen earlier. These are some of the built up sections. The built up section is nothing but to be combined some of the sections together so that its force carrying capacity is increasing. The force carrying capacity is directly proportional to the moment of inertia and the moment of inertia can be increased by adding or mixing different shapes. See first what we see is like channel back to back where two channel sections are added back to back so that it resembles like I section.
I section is the most commonly used section because of its more moment of inertia about major taxes since more weight of material is concentrated away from the taxes then more moment of inertia is there. Here combining two channel sections we can have more thickness of the web also as it combines. This is flange which we see in the top and which is vertical is called as web. Web will carry mostly the shear 90 to 95 percent of shear force is carried by web whereas 5 to 10 percentage is carried as a moment bending moment.
Whereas flange 90 to 95 percentage of bending moment is resisted and 5 to 10 percent is of shear force is resisted with the flange. So if the more bending moment is there and if you want to resist more bending moment then the flange of the beam has to be enhanced. And if it wants to resist more shear force then thickness of the web has to be increased. In that manner we have to select the sections accordingly. Second section what we see is a plate girder section.
Plate girder is nothing but we add 3 plates and we add and weld it together to act like a resemble like a I section. Here as per the design we can have a choice of thickness of the web and thickness of the flange accordingly. We can design and we can customize what kind of thickness of web and what kind of thickness of flange is required. Third one is reinforced isection. We already have an isection say we have ISMB 300. If we want to increase its moment carrying capacity say if we want to resist more moment then obviously we have to increase the thickness of the flange.
As I said already the flange is going to carry more moment of more bending moment. Hence to increase the more bending moment capacity we are going to add some plate on the flange. So it is called as top and bottom plate. It is called as reinforced dissections. In most cases either we use a next section if we have a height constraint say for example if you want to use section which is not more than 300 depth we use ISMB 300. If ISMB 300 is not enough to resist the forces then we add some plate to the flange so that it resists the force that is anticipated to come on the beam.
For example you already construct or you made a beam then later the client says that more load is anticipated to come on the beam. So instead of changing the beam completely cutting it off we add a flange plates top and bottom so that its capacity moment of inertia is increased. So bending moment carrying capacity is also increased. Fourth one what we see is angle back to back where we arrange two angles back to back such that if you cut it across vertically it is symmetrical about both axis.
So in that way to resist that force about that axis can add this angle this way so that the moment of inertia is increased. Mostly this type of arrangement we see as a bottom chord or top chord of trusses nothing but roof supporting structure which spanning for column to column for set kind of width of the building. If you want a building of 20 meter width we have a spanning of trusses to 20 meter and we have to provide an angle section or box section as a top chord or bottom chord.
This is a kind of arrangement which we normally see in a truss bottom chord and top chord. And then fifth type is called as I section with inverted channel. Here this type of arrangement we see normally when you wanted to have a crane runway girdle. Girdle is nothing but a beam. So we have a crane. Crane is something which is meant to operate in an industrial structure to carry a material from one part to another part. Or to have an operation inside the industrial building. Hence to run that crane from one end to another end we need to have a beam of this that is called as a crane runway girdle.
So this is kind of the crane runway girdle where sometimes to accommodate a rail on it. Rail is nothing but what we see normally when a train track is having a two rail right. The same way there will be kind of rail which is sitting on the top of the flange over that rail the crane can be running. Sometimes the flange may not be enough to accommodate that load due to rail and then we need to put a channel section inverting it this way and then connect it along.
So that you place a rail on it and then it can maneuver all over the length of the building. So these are some of the basic built up sections or composite sections where we have a different type of arrangements such a way that we enhance the moment of inertia or the radius of gyration so that we increase axial load carrying capacity and moment carrying capacity also so that it can be utilized as per the purpose it has to be served. So coming to the steel behavior and properties where now we will be discussing how the steel behaves when it is loaded and through the graph stress strain curve.
So the stress is load acting per unit area and then the strain is the deformation which is being recorded when load is applied. So in detail we will see how the steel is going to behave when we apply the load and then we plot a graph and then we can infer lot of data or lot of properties that is supposed to be coming on the steel using that graph. So now we are going to see the stress strain behavior of a steel. So behavior of. Steel is ascertained or understood from the stress-strain behavior that has been plotted across.
Before getting into much in detail about how the stress-strain behavior of steel is studied, I have a slight recap of why mild steel is used as most commonly used metals in civil structures. These are some of the properties which are the advantages of this steel is going to be inferred through this steel stress-strain behavior. Steel is equally strong in tension and compression. Tension is a force which is outside of the material which is compression is a material which brings the all the molecules together which is the force to coming towards a member.
The brittle metals are strong in compression but weak in tension. Some of the examples of brittle materials are RCC cube which is brittle in nature which is very good in compression but when tension force is applied it is very weak. Since steel is equally strong in both tension and compression it is preferred over RCC being strong in tension compression we will infer through this graph and another property is high ductility. Ductility already said I said that it is a property which resists member ductile material can undergo large deformation before fracture.
Therefore steel structure will slow down the initial warning before the collapse or fracture because it gives a warning how it actually deform shape is going out of control before it collapses. This is called as plastic deformation. This plastic deformation also can be recorded in the stress-strain behavior of the steel. Then coming to the Young's modulus of the steel almost equal in tension and compression. So, it means the theory of bending can be applied with full perfection since the Young's modulus in tension compression are same. So, most of the brittle materials have different Young's modulus in tension compression brittle material means always keep in mind that RCC cube is a brittle material.
So, it is having a different Young's modulus in tension and compression whereas steel is having same Young's modulus in compression and tension. And this it is said to have a better property to resist bending and then to go much in detail how this is been plotted. To have a idea let me say that we perform a test. The test is performed in a universal testing machine. It is called as UTM machine. So, UTM machine can be used for a tension test, compression test and also the shear test.
Initially, we perform a tension test where we plot a stress-strain curve. So, to do a tension test we choose a solid cylindrical specimen of gauge length to gauge dia ratio as 4. Gauge length is nothing but a length of the specimen which we are taking and then diameter of specimen. This whole standardization of this material is done in ASTM which is American Society of Testing Machine. The standard size of specimen to be chosen is length is 2 inches and the diameter is 0.5 inches and the hence we get a L by D which is the length by diameter as a 4 and then we plot a stress-strain curve.
How we do it? So, what we do is like the we mark some gauge points at one either end. Then, we apply a load and we gradually increase from 0 to say a load called P. Then, we measure that the deflection at those gauge points which we place it in the top and bottom using a instrument called extensometer. So, we take a specimen we mark the position in the top and bottom and we mark it as 1 or 2. Then, we measure the deflection at those point using the instrument called extensometer while applying a load from 0 to say a load called P.
Then, we plot a graph between stress and strain. Then, let us get deep into what is stress, what is strain, what is stress-strain curve and what is the significance of stress-strain curve. What is stress? A stress is the internal resistance of the metal offered against load or deflection. It is a measure as a force per unit area roughly speaking even a pressure force that is also a force per unit area having a same unit Newton per mm square. What is the difference between stress and pressure?
Stress is nothing but an internal resistance of the metal whereas pressure is external load distributed on a unit area. So, there is a clear understanding need to be had between the stress and then the pressure. Stress is internal resistance of a metal against the load or deflection whereas pressure is external load applied on the unit area. So, applying I mean the measuring of internal resistance of the metal is through the load which we apply. Hence, the deflection or strain are the free to occur coming to what is strain.
Strain is also called as dilation. It is a measure of deformation as a result of stress being recorded. So, stress is defined as a deflection per unit area. So, it is nothing but a deflection. So, it is not a having a I mean deflection per unit length. So, hence meter by meter it is going to be a dimensionless quantity. So, when there is a deflection is free to occur then there is no stress in the direction. So, for example, you have a specimen you have a uniaxial loading.
Uniaxial loading means you apply a load in one axis. Say, we are applying load in x direction. So, it is free to move in y and z direction the lateral direction and longitudinal direction. Hence, if there it is free to move in that direction we have a strain in the direction, but there is no stress in the direction. So, it should be remembered always that when there is a restriction there is no strain to occur whereas stress will be recorded. So, that way we can understand stress and strain.
This strain is measured through there is a instrument called strain gauges where we can measure the strain. So, we plot stress strain curve with stress in y axis and strain in x axis. So this stress strain curve gives a relationship between stress and strain. So this stress strain curve is going to be different for different materials. So it can cannot be same for steel or concrete or aluminium or gold or silver. It is going to be different for different materials. And it should be noted that it will be different for a same material of different composition also.
Say for example, high strength steel is having different stress strain curve and mild steel is going to have a different stress strain curve. And then reinforcing steel will have different stress strain curve. So different material is going to have a different stress strain curve and same material with the different properties I mean different composition of materials also going to have a different stress strain curve. So, this stress strain curve is obtained by finding deformation for different stresses. So, we apply load and then we measure a strain, so the strain is called as a deformation, this deformation is measured using strain gorges and through that we plot a stress strain curve.
So, what we infer from the stress strain curve, we infer lot of properties of the material, different properties which we have discussed in earlier slide, some of the advantages which we talked about a steel, all these things will be inferred in the stress strain curve which can be plotted.