← Previous lessonFree lesson 2 of 3 · lesson 2 of 59Next lesson →

Unlock all 59 lessons of Analysis and Design of Industrial Structures using STAAD.ProFull course ₹40,000 · paid

Price & syllabus
Free lesson · 20 min · no payment

Advantages and Disadvantages of Structural Steel and IS Grades

A free lesson from Skill-Lync's Analysis and Design of Industrial Structures using STAAD.Pro course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “Advantages of Steel in Construction”

What will you learn in this free Analysis and Design of Industrial Structures using STAAD.Pro lesson?

The lesson defines tensile strength, elasticity and ductility, then lists steel's advantages (faster erection, recoverable scrap, factory quality control) and disadvantages (corrosion, fire, fatigue, maintenance). It also covers Indian Standard codes such as IS 2062, the E250 and Fe410 grades, and how carbon, manganese and silicon affect strength and weldability.

  • Tensile strength, elasticity and ductility definitions
  • Corrosion, fire and fatigue drawbacks of steel
  • IS 2062 and other steel standards
  • Carbon and manganese effect on weldability

What comes after lesson 2?

The next free lesson is lesson 3, “Steel Shapes, Built-Up Sections and the Stress-Strain Curve” (18 min). Later in Skill-Lync's Analysis and Design of Industrial Structures using STAAD.Pro course (paid): lesson 4, Understanding Stress-Strain Curves and Material Behavior; lesson 5, Introduction to Industrial Structures using STAAD.Pro; lesson 6, Types of Industrial Structures and Their Configurations. The full course has 59 lessons (27 h 53 min of video); see the course overview or its price and syllabus.

Lesson transcript

Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.

Why steel? Steel is preferred in construction because of its advantage. As I said already it is having more advantage compared to that of disadvantages and what are the advantages it has because of which this material is preferred compared to that of other materials is high tensile strength. What is tensile strength? Let us see what is tensile strength basically. Tensile strength is measurement of force required to pull something, pull such as a rope, wire or a structural beam to a point where it breaks. So, if I wanted to make you visualize or take an example of a small thin rod or thin material, thin steel rod, where you try to pull, you apply a tensile force.

Tensile force is something we make a force which comes out of the material. It is not coming inside like. So, you pull it, you pull it outside. Then at certain point, it is going to break. So, that strength or that force which makes the beam or the material to break is called as a tensile strength. And compared to other material, if you apply the same force, this is not going to fail even lesser force compared to that of the force which has been applied to the steel.

So, the steel is said to have a high tensile strength. So, we have high tensile strength also which is going to have a more strength compared to the conventional or a mild steel. We have a different type of steel called as mild steel, high tensile strength or high strength steel and all which we will be discussing in the future slides. So, basically it is having a high tensile strength. Then it is having a property of elasticity and ductility. So, what is elasticity? So, the elasticity is the ability of a body to resist a distortion. So, it is going to resist a distortion and then it returns to the original size and shape when the force is removed.

So, you apply a force and then once you remove a force, it gets back to the original position by resisting the force which is applied. So, this property of the material is said to be the elastic property and this is called as elasticity. Now, steel do has a property of elasticity when you apply a force and then remove it suddenly it gets back to the original position up to certain point that is called as elastic limit that we will be discussing. So, keep in mind that elasticity is a property which is ability of a body to make the material to come back to its original position when the force is removed.

So, this is one of the important property steel do possess compared to that of other material in addition elastic property some other materials may have a better elastic property but that is not that means that that material is going to have a better choice compared to steel. So, balance of all the properties is going to make this steel a better choice. So, then comes the ductility. So, ductility is again a mechanical property to sustain a plastic deformation under tensile stress before failure. Repeat it or call it again like you listen it properly like it is a mechanical property which makes it to sustain a plastic deformation before failure when the tensile stress is applied.

So, what is plastic deformation so what is plastic deformation so we talked about elasticity which is the property to make the material to come back to its original position when a force is removed ductility is also property which makes the material to stay in a plastic deformation plastic deformation is the opposite of elastic deformation which is that it does not come back to its original position. So, plastic deformation so plastic deformation when a tensile force is applied before it failure this is a very important property because when steel is going to fail it shows a property of symptom that it has undergone a plastic deformation this can give a symptom that there is something wrong in that this failure is going to occur and give a warning.

So, in concrete and all we see when a crack is there this place is going to fail or something is happening or something. Similarly, similarly when steel when a deformation or a kind of buckling different terminologies are there which I will be saying sometimes when the time come let us say that out of shape keep in mind that it is out of shape or deformation and it does not come back to its original position when the force is removed before the failure occurs. So, this happens so this happens so this happens so this happens so this happens so this happens when things are going to fail or this property is going to be very much helpful to ascertain that something is wrong is going to happen then the quality is under control the quality of the material is under control because the whole manufacturing of the steel is going to happen in a closed environment unlike in steel unlike in concrete RCC where we pour the concrete we mix the concrete and everything is happening in the outside environment.

So, where the construction is going to happen where the construction is going to happen where the construction is going to happen. So, the idea is concrete is some we have a strength everything is monitored in factory itself they come and pour it yet there will be some kind of a difference from what strength they say and then what is that is going to be in sight once the casting is done. Whereas in steel we say because everything is happened in a closed environment unless there is some kind of workmanship and some kind of allowance happen where we have everything under control so we have a quality which is much better compared to other materials especially the RCC then comes the faster and easier erection.

So, why this is said to be fast erection because once this is like a plug and play like we make all the I mean we design and then we mark each this is going to be column this is going to be beam this is going to be the tie beam and this is going to be sheet supporting beam or everything we make and we label it in sight. I mean wind fabrication yard fabrication yard fabrication yard is where the whole thing is done separately then we bring it to the site and then we connect it using bolt or welding.

So, erection is happening in the place that where we want that building has to be functioned. So, erection happens in the place of where the building has to happen and then the manufacturing or the fabrication happens in some other place or factory. So, once this is done easily erect it say when all the materials comes to the site within some weeks time we can see the building is erected compared to that RCC where we start from the scratch in the site only. So, that is a very important advantages compared to RCC then recoverable scrap recoverable scrap is very very important because we can recover once that buildings serve its purpose or function.

We want to relocate that building to some other place or we want to reuse that building for something or you want to make another building in the same spot using the material that is being recovered from the building which is nearby. Everything is possible in steel because you just remove the bolt or if it is welded you cut it across and then you take it and then use it for wherever it is required. In RCC you can't do it because you can't cut the beam or column and then use it in another building and all.

Another one is value after demolition say also having a similar kind of meaning like what we have spoken sometime back like recoverable scrap. Once the demolition is there that you take all the materials outside it do have an value and it can go to the market and can be recycled. We can give it to the market and then that can be recycled and again it will be made like a steel pellets and then again that steel will be made like a sheets and then sheet will convert into a member.

So the whole process is a cyclic process and then it can be recycled and reused. So that is very important advantage and these are the advantages which makes the steel of better choice compared to that of the other materials. Is steel the perfect option? Yeah steel is a good option but why steel? Is steel but is steel always the perfect option? No not sometimes because steel may not be the perfect option but some of the disadvantages it do have which has to be considered and for that we have to be better to know what are the disadvantages.

We have to be prepared enough to handle those disadvantages before using that material. Steel has some disadvantages so this requires periodical maintenance this requires periodical maintenance because it undergoes a lot of there will be I said right there will be ductile material when this material has undergone loading and all. There may be some symptoms or some kind of bending or deformation happened so it has to maintain periodically and then painting has to be done otherwise it is very tough to monitor whether the building is safe or not and all.

It needs a periodical maintenance then it is prone to corrosion because this steel is react with oxygen and it can corrode fast especially when it is nearby the seaside and all where steel structure this corrosion can happen and then the strength of steel has to be belittled. Since there is some methodology called as we apply a painting zinc coated painting and all which makes that steel to be corrosion free and then we have a galvanization process which makes that steel we dip it in a galvanization pond and we makes it not under corrosion.

And we do have a corrosion resistant steel which is a must cost layer. Hence, there should be balance of the usage of, I mean, if you are going to choose material, it should not pump up the cost of the whole thing also, like, it should be like a balance between the material and then the cost-wise, economically-wise also. So, this is prone to corrosion. Then another is, it requires a fire protection. This is a very important disadvantages, because even a structural engineer has to keep in mind, how much time it is going to resist the fire.

Say that fire resistance, there is a time like 30 minutes, 90 minutes. Once the brigade people comes inside and then they occupy and then they try to exhume or bring down the fire and all. So, there should be some kind of time to be given before it gets collapsed or something, when the fire breaks out. And proper fire alarming should also be kept inside the building, which gives a warning that the fire has broken out and sooner the proper first aid has to be done. Not that fire to be spread and then make the building to collapse completely.

So, proper fire protection has to be done. Then, there are a lot of methodology, I mean, a lot of facts that has to be done. Then, it is susceptible to brittle fracture and fatigue due to cyclic loads. So, as I said, the steel is a ductile material, but it do have a brittle fracture when high-strength steel has to go. Because the high-strength steel is not have less ductile. And then, this brittle fracture is similar to that of how the concrete RCC crack comes and then the whole beam gets broken.

Then, the fatigue due to cyclic loads. Cyclic loads is a load which comes on and on and on. Say, very little force, but it repeatedly comes. The repeated loads are called as cyclic loads. So, this causes fatigue on the material because of cyclic, which makes that steel to, when it is exposed to that of repeated cyclic small amount of loads. So, these are the different disadvantages that has to be considered before or when steel has been chosen as a material or as a choice of material for construction.

Then, comes the types of steel. These types of steels are, we have a structural steel. This gives an idea of different Indian standards, what has to be referred to give a property of different type of steel structures. So, we have steel sheets and stripes and steel for tubes and all, steel casting and all. So, right-hand side, we have different Indian standards. These codes will give different properties and how the manufacturing process and all. For example, this 2062 will give all the properties about mild steel and 1977 will give about low stem steel and 3502 will give about checkered plates and then 5517 will give hardened and tempered steel.

So, these steels are different type of steel depend upon the manufacturing process and then usages and all. Sometimes, the client will give a specification that he has this type of steel and then a different kind of environment may have a preference of that kind of steel to be utilized. As a listener, just have a go-through of this different IS standard, what this talks about and what is what and just have an idea about it alone. Sometimes, specifications will be given and for that, we have to see all this, refer this, all this IS codes and all.

Then, 85800 is going to give a high-grade raw material and then high-grade steel and all. Proceeding to the next slide, this gives us steel composition. So, what are the different compositions that steel is made up of? Starting from a type of steel, this is first is called as a standard structural steel, then micro alloyed, then medium high-strength steel. The E250 is we call as grade, E250 is a yield strength. Keep in mind what is yield strength. Let me explain in the preceding slide where we see about the steel property.

Fe410A is, 410 is called as ultimate stress, whereas A, B, C is called as the strength at the climb, whether at 0 degree or minus degree or 20 degree. At the temperature, what is the strength and all? It adheres to the Si-S code 2062 and C is the carbon, manganese, silica and then phosphorus and then sulfur. So, how much quantity of in these materials is being presented in this? And then the carbon equivalent, keep in mind there is all this composition which we have presented in numbers here are in percentages.

So, this carbon equivalent is one of the thing that very important when weldability is coming into picture. Weldability is when you weld a material, how much is going to be like you weld it to beams and column, whether the welding has to be proper or how much welding prioritization or thing has to be kept in mind. This carbon content plays a major role in welding. Then E300, E410, I mean E450 or high strength steel. So, in RCC, we will be seeing Fe415 or Fe250, Fe500, where that 415, 250, 500 means yield strength in Newton per mm square.

Whereas here, Fe410 or 570 or 590 is going to be ultimate tensile strength. We already talked about what is tensile strength, here it means that the ultimate after which it is going to be fractured only. So, that is the difference between the reinforcing steel which we use it in RCC and the structural steel which we use it in structural steel construction. So, the different composition and what are the advantages and disadvantages that is going to be giving because of the material. One is the carbon. The carbon will improve the strength, whereas it reduces the weldability and ductility of the strength.

So, this carbon content will of course improve the ductility when it is less in number because when carbon content is less, the ductility will be more. So, when ductility is more, it will take more of impact loads or dynamic loads. Hence, the ductility will make that material to go to a plastic deformation and not to have a failure. It can reach about the ultimate stress before it gets failure. Whereas the more carbon content, the ductility will be sparred and then it will be of we are letting go that kind of property.

Then comes manganese. The manganese will improve the strength and toughness. It improves the toughness of the material. Toughness is basically the resistance that material gives before it gets failure. So, the manganese will of course increases the strength and the toughness and that also will reduce the weldability of the material. And silicon is used for our deoxidizing hot steel during steel making process. And it improves the toughness of the steel. We have a process of hot roll section and cold form section. It depends upon the manufacturing process of the steel.

And here it is used in deoxidizing part of that hot steel steel making process. And those silicon which has to be if it is more also will affect the weldability. There has to be a perfect balance between all this carbon manganese and silicon. Which improves or the strength and then toughness by not compromising on the weldability also. So, other materials like nitrogen, phosphorus and sulfur are all added in a small quantities. Then these are the standards used in steel industries. Starting from Indian codes we use Indian standards which is called as IS series.

So, IS 2062 whichever we talked before. These are all our Indian standards. Then RDSO we called as Railway Design and Standard Organization. All the railway bridges has to adhere or has to follow these series of Indian codes. Then state road transport standards are where lot of highway bridges and all has to be constructed. It has to follow AST-RU series. AST-RU is called as Association of State Road Transport Undertaking. So, these different bodies will have a different series and code and standards that has to be because when you see this railway bridges there will be more of emphasis on movement of train on bridges as to be there and how this material is going to behave.

Then AST-RU will have more of a point load, running load, the traffic volume, how much a bus or a truck, wheel loads will be taken care in this series. Where the IS code Indian standard we will see the conventional building, conventional factory building and industrial buildings. So, in our topic we will be mostly covering on IS series of IS codes only. Then if you go past we have other codes called as in American standard we called AISI where American Iron and Steel Institute and SAE series which is society of automotive industry where thin sheet of material.

In automotive we use a coal form steel mostly because it is a very thin sheet of steel and all is there. And British series is called as EN-RVSS and then the other series German series standards we called as DIN series. Japanese standards we called as GIS series, French series or AFNOR series. So, have a look at those series. Sometimes when you walk in MNC companies those kind of standards will be given. We have to use those kind of materials because we have a site in Dubai where we have to use American standard of steel.

Then we have to use American steel having that kind of properties then you have to look into it and if we have a project in German and all we have to use DIN series of course. Of course there will be little depends upon the material procurement and then how the process of manufacturing. Little bit there will be difference or almost the steel behavior is going to be universal. So this is the content for first session of week 1. Let us call it for this session. We see you in the next session. Thank you.

Want the rest of Analysis and Design of Industrial Structures using STAAD.Pro?

Get the full course syllabus and fees.

The full course is paid (₹40,000). We'll send the syllabus and call you back within one working day.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Full course · paid

Unlock the full Analysis and Design of Industrial Structures using STAAD.Pro course

The remaining 56 lessons, mentor-reviewed projects and a certificate come with the paid course (₹40,000). Leave your details: we'll send the syllabus and fees and call you back.

Get the syllabus and fees

A counsellor calls you back within one working day.

By submitting you agree to our Terms and Privacy Policy.

Grow by Skill-Lync · free lesson

Start watching

Free, no payment. Leave your details once and every free lesson on Grow plays straight away. A Skill-Lync counsellor may call you about the full Analysis and Design of Industrial Structures using STAAD.Pro course.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.