Unlock all 12 lessons of 5G NR Protocol StackFull course ₹40,000 · paid
5G Frame Structure, Numerology, Resource Blocks and Bandwidth Parts
A free lesson from Skill-Lync's 5G NR Protocol Stack course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “Week 1 Session 2”
What will you learn in this free 5G NR Protocol Stack lesson?
After a short recap, the lesson explains why 5G has numerology, with subcarrier spacings from 15 to 240 kHz, and how it changes slot duration. It covers slot formats for TDD and FDD, resource blocks and elements, and how bandwidth parts help UEs save battery.
- Subcarrier spacing of 15, 30, 60, 120 and 240 kHz
- How numerology changes slot duration, with 14 symbols per slot
- DL, UL and flexible slot formats configured through RRC
- Bandwidth parts and why they reduce blind decoding
What comes after lesson 2?
The next free lesson is lesson 3, “NG Setup Request and Response Code Walkthrough in srsRAN” (22 min). Later in Skill-Lync's 5G NR Protocol Stack course (paid): lesson 4, Week 2 Session 2; lesson 5, Week 2 Session 3; lesson 6, Week 3 Session 1. The full course has 12 lessons (4 h 24 min of video); see the course overview or its price and syllabus.
Lesson transcript
Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.
Hello everyone. Welcome back to the course 5G and Radio Access Network. This is our session 2 from week 1. Today we'll be discussing about 5G AIR interface. Let's do a quick recap what we discussed in the last session. So we did a quick introduction of 5G, what are the major changes in 5G and we also learned about various 5G use cases like throughput use cases, AEMBB, ultra-reliable and low-latency use cases, URLLC and MMTC for the IoT kind of use cases. Also we discussed about the real use cases of 5G in the industrial network.
Then we learned about different bands of sub-six and millimeter wave. And also we touched upon SA and NSA mode of development. Then we spent quite a lot of time for 5G architecture, how this architecture is different from the earlier 4G networks. And then we learned about the 5G protocol stack, various protocols in the control plane stack and user plane stack and how it is different from the LTE and what new entities have been involved. To add on, we also discussed about the service-based and the reference-based architecture of 5G control plane core networks, okay, and why this was done.
These are the topics for today. We'll discuss about 5G frame structure, slots and the different numerologies. Then we'll discuss about the resource block and the resource element. Then we'll understand how a bandwidth part looks like, what is a bandwidth part, what is the use of it, because this has been introduced newly in the 5G. Then we'll do a quick summary at end of the session. These are the learning objectives. So in this session, we'll look into the 5G frame and different numerologies. We'll understand the 5G bandwidth part and run resource blocks.
So let's start with our first topic for today, 5G frame structure, slots and numerology. Numerology refers to spacing of sub-carriers in frequency domain. Now, the question comes, why this numerology came in 5G, why it was not there in LTE, because the sub-carrier spacing was there in LTE also of 15 kHz, but why this new term came? So in LTE, the sub-carrier spacing was always fixed. It was just 15 kHz for any kind of deployment. So this numerology didn't come into the picture, but here in 5G, we have different sub-carrier spacing.
It has 15, 30, 60, 120 and 240 sub-carrier spacing. So this different numerology basically defined what is a sub-carrier spacing. That's the reason this numerology term came in 5G, which was not there in 4G. So 5G supports various sub-carrier spacing. And sub-carrier spacing determines the bandwidth of the frequency domain and the time domain duration in a single resource element. So in single resource element, what should be the duration of the time in the time domain and what should be the bandwidth in the frequency domain is defined by the sub-carrier spacing.
A resource element has dimension of one sub-carrier in the frequency domain and one symbol in the time domain. So in terms of the frequency domain, it is same as LTE. There also it was one sub-carrier spacing. But in LTE, we had one slot in the one resource element, but here we have one symbol as a resource element. So it means the scheduling can be done in one sub-carrier and one symbol also. Okay. Sub-carrier spacing is inversely proportional to slot duration. So as your sub-carrier spacing increases, your slot duration decreases and vice versa.
So if your sub-carrier spacing is coming down, then your slot duration will increase. Okay. So as the slot duration decreases with an increase of sub-carrier spacing, the length of OFDM symbol also decreases. Okay. Length of OFDM symbols, once we see the frame structure using some drawings and some figures, then we'll understand it in detail. A longer OFDM symbol is suitable for large cell radius and is more tolerable to fading channels. This also we'll understand in detail, like if fading channel is very bad and the channel is too faded and your cell radius is too large.
So to mitigate that, we use the longer OFDM symbols. Lower sub-carrier spacing can be used in lower frequency band as the bands are smaller. 5G numerology and use cases. So higher frequency has a wide range of frequency drift. So a wider sub-carrier spacing is used and lower slot length can be used for the application that requires low latency. So low latency means you have to process in a millisecond. So for example, if your one slot duration will be too high, then that much time you will take to transmit or to receive the data.
But it will be less, then the lesser time will be required to transmit and receive the data simultaneously. That's the reason lower slot length is used for the low latency cases. As we know, 5G can support various use cases like EMBB along with that URLLC. That's the reason this various numerology is having different sub-carrier spacing and low or high slot duration. So these are the deployments you can see here for the 15 kHz, 30 kHz, 60 kHz and so on. The OFDM symbol duration for the 15 kHz is 66.67 microsecond.
It means the one symbol duration. Then as the, you can see the first row, as the sub-carrier spacing increases, it becomes 50 to 30. Then the symbol duration becomes exactly half. Now it became 33.33. As it increased further to 60 kHz, the symbol duration became 16.67 and so on. And also you can see the cyclic prefix duration. It was 4.69 for 15 kHz, then 2.34 for 30, 1.17 for 60 kHz and so on. Similarly, the slot duration also, you can see for the 15 kHz, it was 1 ms.
Then 30 kHz, it became 0.5 ms. 60 kHz, 0.25 and 120 will become 0.125 and 240 will become 0.0625. The carrier bandwidth, you can see 15 kHz can support only up to 20 MHz. So 1.4 to 20 MHz. So 20 MHz was the highest in LTE case. Then we have 80 to 100 MHz in 30 kHz, then 160 MHz in 60 kHz and 400 MHz in. I mean, once you go till the highest, then 5G can support up to 400 MHz carrier bandwidth. Similarly, you can see for different sub-carrier spacing, what is the Doppler effect, what is the frequency bands and what are the use cases.
So as we know, there are mainly 3 use cases like EMBB, URLLC and MMTC. So here you can see 15 kHz used for mobile broadband, which is EMBB and Massive IoT both. Then 30 kHz is used only for broadcast like MBSFN. Then 60 kHz can be used for EMBB, normal CP and broadcast for the extended CP. And similarly, when you go further in the millimeter wave sub-carrier spacing like 120 and 240, then that is mainly used for URLLC. So here you can see the spec reference has been given, 38211 version 17.2.
If you see, this is a table which has been taken from there, numerology 0 to 6, okay. And you can see for the different numerologies, you have the second column defines the sub-carrier spacing. So for 0, it becomes 15. For 130, 260, 3, 120, 4, 240 and so on. And the cyclic prefix, you can see here in 15 and 30, so numerology 0 and 1. We call numerology as mu in short form. So mu 0 and 1 supports only normal. Similarly, 3, 4, 5, 6 supports normal.
And 2 supports both normal and the extended. Now here you can see the numerologies from this diagram. You will understand it better. How this sub-carrier spacing is inversely proportional to the slot duration. So you can see on top of the figure 15 kilohertz sub-carrier spacing. Then your slot duration is 1 millisecond, okay. Then the 30 kilohertz, the slot duration became half, 0.5 millisecond. 60 became again half to 0.25. 120 became further half, 0.125. Moreover, 240 became 0.0625. Here you can see 38.211 version 17.2.0 table 4.3.2.1.
If you see, you can find this table, okay. And this table has been represented using this diagram to understand it in more detail. Now here you can see the frame structure. So just let's see. Take LTE, one radio frame is having 10 subframe and each of 1 millisecond and one frame has been extended here to show how this one subframe contains 14 number of symbols. So you can see here this one millisecond, this one yellow box is yellow box or orange box is showing one millisecond out of one radio frame and this is one millisecond basically, okay, which is having one slot and this one slot is having 14 symbols.
So this is nothing but this has been expanded here. So you can see here 1, 2, 2, 14 symbols equals to one slot equals to one millisecond. Now the earlier one was for numerology zero where you have 15 kilohertz subcarrier spacing. Now mu1 is having 30 kilohertz subcarrier spacing. 30 kilohertz means your slot duration will be half, right? So one millisecond here, you can see there will be two slots in one millisecond and each slot will be having 14 symbols. So 14, 14, 28 symbols in one millisecond.
Similarly, for mu4, you can see here how many slots in one millisecond, there are eight slots and each slots are having 14 symbols. So total number of symbols in one millisecond equals to 14 into eight. So you can see here how the subcarrier spacing is increasing and slot duration is decreasing, but each slot will be having 14 number of symbols. It means symbol duration is actually decreasing, okay? Now 5G slot format. This is also one of the important term. What is slot format? So a slot can be categorized as DL, UL or mixed.
So DL means all the symbols, all 14 symbols in a slot is DL if the slot has been marked as DL. If it has been marked as UL, then all 14 symbols will be UL or it can be a mixed like uplink and downlink transmission both. So one slot will have few downlink symbols and few uplink symbols. In case of FDD, there are two separate carriers for uplink and downlink transmission. As we know, it's a paired spectrum. So one is for downlink and one is for uplink.
For downlink transmissions, all symbol in a downlink carrier slots are used. For uplink transmission, all symbol in a uplink slots are used, okay? So it is just like, as I said, it's a paired frequency. So for downlink, all for downlink and for uplink, all for uplink. There is no any mixed, like not one slot for downlink, one for uplink like TDD. So in TDD slot configuration, each symbol within a slot can either be used to schedule an uplink packet or downlink packet or it can be flexible.
Flexible means either it can be used as downlink or it can be used as uplink. So the flexible symbol can be used to either uplink or downlink as per requirement, okay? Then the slot configuration via RRC consists of two parts. So now the question is how the UE will come to know what is a slot configuration, which one is downlink and which one is uplink and which one is flexible. So this is communicated to the UE using the RRC mechanism. So RRC can have either configuration common or configuration dedicated, which can be used to tell the UE what is the slot configuration.
Now here you can see, this is how the communication goes. So once you see the RRC message, you will see there will be DLUL transmission periodicity, number of downlink slots, number of downlink symbols, number of uplink slots, number of uplink symbols. This is very important to learn and to understand how UE defines. So slot periodicity, this will tell that, okay, what is the periodicity, which will, I mean, the duration after which the same thing will be repeated. So let's say it can be 5 milliseconds or 3 milliseconds or 10 milliseconds, okay?
In those, for example, let's say we are taking 5 milliseconds. So now number of downlink slots means in that 5 milliseconds, if this is set to 2, then from initial 0 and 1, 2 slots will be for downlink. And then we will go to the uplink slots, okay, the fourth parameter, which is from the end. So if it is 2, again, 2 from last. So first 2 from beginning is downlink slot, last 2 is the uplink slot. And in between, now there will be one slot left, which is used for both, means the downlink and uplink.
Now, how many symbols are for downlink and how many symbols are for uplink will give you information by this parameter, number of downlink symbols and number of uplink symbols. Again, in that particular slot, number of downlink symbols is beginning from the slot and number of uplink symbols is from end of the slot. Now resource block and resource element. And, okay, so here you can see this is frequency domain, okay, the subcarrier and this is a time domain. So this is one resource element. You can see this is 14 symbols and one symbol and one subcarrier is your single resource element.
So K and I. So the lowest time frequency resource across one subcarrier of an individual or uplink symbol is known as resource element. One NR resource block contains 12 subcarriers in frequency domain. So this is same. This is just like LTE, your 12 subcarrier, but the difference is in terms of slots. Now next is bandwidth and bandwidth part. So 5G supports bandwidth of up to 400 MHz per carrier, okay. This is too much if you compare from the LTE. NR supports channel bandwidth of 100 MHz for lower bands with frequency less than 6 GHz and channel bandwidth of 400 MHz for higher bands with frequency in millimeter ranges.
There are defined minimum and maximum number of resource blocks in each numerology. Actual RB is a channel bandwidth after the guard band has been removed. So if you see the subcarrier spacing, right. So for example, in 100 MHz, if you have lesser subcarrier spacing, then you will have more number of resource blocks, right. But if you increase the spacing between two subcarriers, then obviously your resource blocks will be less. So in 100 MHz only, you will have lesser or higher number of resource blocks depending on the numerology.
Now bandwidth and bandwidth part. So here you can see this is a whole frequency region like the whole bandwidth, okay. And in the whole bandwidth, these are the active resource blocks. So there can be some common resource blocks and there can be some active resource block. So active resource block can have different partition. I mean, there can be two, three or four partitions of the whole frequency region, which is called one bandwidth part, okay. So here you can see the minimum and maximum RB is possible in 15 KHz and 240 KHz.
So 24 to 275, 24 to 275 and 240 will have 24 to 138. So now when is minimum, when is maximum. So you have, when you are using the lowest subcarrier spacing, then you have maximum RBs. And when you are using the highest subcarrier spacing, then you will have the minimum RBs. Now bandwidth and bandwidth part. So a bandwidth part is set of contiguous resource blocks. A bandwidth part provides services to UE that do not support the full channel bandwidth, okay. So for example, as we discussed, 5G can support up to 400 MHz, right.
But there may be some UEs which may not be able to support up to 400 MHz. So for that UE, the network can configure a part of the whole bandwidth out of 400 MHz. Let's say it can configure 50 MHz as one bandwidth part and that can be used by a particular UE. And a UE can be configured up to four bandwidth parts per carrier, okay. And if a UE has been configured by one bandwidth part, then the UE has to transmit and receive within the same bandwidth part.
So it can be even activated or deactivated. There are two mechanisms. Either you can use the RRC signaling or you can do it dynamically using the DCI to activate and deactivate the different bandwidth parts. Now here you can see the bandwidth part in detail. You will understand it more. So in the diagram A, you can see there is a whole overall frequency. So let's say it's a 100 MHz frequency starting from 0 to 99. Now you can see here just one bandwidth part that is BWP1 has been configured.
It may be just 10 MHz, 15, 20 or 25, okay. Now you can see the next one. Here there are two bandwidth parts. This is called overlapping bandwidth parts. So one bandwidth part is configured BWP2, which is greater than BWP1. So BWP1 may have just 10 MHz, but BWP2 may have 20 or 30 MHz. Similarly, there can be two different bandwidth parts configured with different numerologies. So here in the picture C, you can see like BWP1 using numerology 1, BWP2 using numerologies 2. So now the question is why this is required, okay.
So as you know, there are several use cases possible and we know there can be different type of network condition where you... You need to use either mu1 or mu2 or mu3 or mu4. So in the same overall frequency, you can use for both type of use cases. So let's say one set of user in the same region needs low latency communication. Then you can configure it to mu3 or mu4. And in the same region, there are a set of users. They need a different requirement like EMBB type of requirement.
Then the other part of the frequency you can configure as numerology 1. Here in the diagram D, you can see there are two different bandwidth parts have been configured. And also there is a space left which can be used for other setup. Okay. So these are the characteristics of a bandwidth part. So the bandwidth part allows manufacturers to design chipsets and UEs with lower bandwidth capabilities. So as we know that some of the UEs may not be able to support up to 400 MHz. So the UEs which support lesser, the network can be configured based on that.
Bandwidth part helps to achieve various 5G use cases with different bandwidth part configuration using a single carrier. So as we saw like in a same carrier, we can configure multiple numerologies using different bandwidth part. Helps UEs save battery by minimizing blind decoding attempts. So as you remember, the blind decodings for the control plane for the PDC-CH, UEs does for the entire bandwidth. So as it is 400 MHz, it will be too huge for the UEs to detect. So before decoding the actual data, it will utilize all its battery in decoding the PDC-CH itself.
That's the reason the bandwidth part, the small, small bandwidth part is configured. And UEs is told that, okay, this is the bandwidth part. We have to look for the control plane. So it has to decode just the fewer part, the smaller part of the whole frequency. Each bandwidth part can be configured with a different numerologies, MIMO configuration and modulation. So as we saw, there are two different bandwidth part in figure 3, which were configured with mu1 and mu2. But not just numerology, you can also have different MIMO configuration and different modulation scheme.
Now here you can see, once the SSB is acquired, so SSB uses 20 RBs, then it goes for acquiring SIB1, which is having different core set. So core set will understand what is core set, okay. Then during the initial random access, some downlink bandwidth part and uplink bandwidth part, which is called the initial. So this is common for the UEs to do the RATS procedures. Once the UEs will be in connected mode, then you can see there are different active bandwidth parts. So this is first active DL and this is first active UL.
And then there is another default DL bandwidth part and this is the same first UL active part. So if you are not configuring any UV to go in a particular active bandwidth part, then it will just go and use the default DL or UL bandwidth part, which is defined by the network by default. Yeah. So that's all from today's session. In this session, we learned about the 5G frame structure, slots and numerologies, why this different numerologies came and how different numerology affects the subcarrier spacing and how different subcarrier spacing affects the number of resource blocks and the slot duration.
Then we learned about how this resource block changed from 4G to 5G, what is a resource element. And then we learned about various bandwidth and bandwidth part, why bandwidth part is required, how using various bandwidth part, we can save the battery, we can support different users and we can support different type of use cases. So that's all from today's session. Thank you so much for joining. So thank you for listening.