Week 8 - Challenge 6 - Core & Cavity Design
N.Siyamil Sarrafath
updated on 06 Dec 2022
Project Details
Leave a comment
Thanks for choosing to leave a comment. Please keep in mind that all the comments are moderated as per our comment policy, and your email will not be published for privacy reasons. Please leave a personal & meaningful conversation.
Other comments...
Be the first to add a comment
Read more Projects by N.Siyamil Sarrafath (16)
Tool Test
06 Jan 2023 11:40 AM IST
Project 2
Aim- To create a tail lamp from the given Class-A surface by following all the design parameters with attachment features, Positive mounting points and ECE(Economic Commission of Europe) regulations. Given Class-A Surface Guidelines followed to create The Tail Lamp CREATE COMPLETE TAIL LAMP USING HOT PLATE WELDING SECTION…
06 Jan 2023 06:16 AM IST
Week 11 Challenge
03 Jan 2023 07:19 AM IST
Week 11 - Final project
Objective With the given input of class A surfaces and master sections, the plastic door trim parts are to be developed following industry standard design guideline using Catia V5 software. Introduction Door panels serve as an interface between the interior of the car and the inner workings of the door, and between vehicle…
19 Dec 2022 07:44 AM IST
Week 4 Challenge
1.The Tooling Direction is basically the direction that the mold pulls apart. The mold is built in two separate pieces, basically. You have a Cavity side and you have the Core side. The Core pulls apart from the Cavity and that's the Dyeline or the Tooling Direction 2. 3.A parting line, in industrial casting…
15 Dec 2022 07:33 AM IST
Week 3 Challenge
14 Dec 2022 12:54 PM IST
Week 10- Assembly Workbench
11 Dec 2022 02:10 PM IST
Week 9 - Project - A pillar Design with Master Section
09 Dec 2022 10:34 AM IST
Week 9 - Project 1 - Door Trim Lower with Engineering Features
09 Dec 2022 07:25 AM IST
Week 9 - Attachment Feature Creation - Challenge 2
09 Dec 2022 05:56 AM IST
Week 9 - Attachment Feature Creation (Ribs & Screw Boss) - Challenge 1
07 Dec 2022 07:33 AM IST
Week 8 - Challenge 6 - Core & Cavity Design
06 Dec 2022 08:00 AM IST
Week 8 - Challenge 4 - Bumper
TOOLING AXIS:- Considering the Ejection from the cavity of the mould after manufacturing the interior trim (switch bezel) must have the nominal 3-degree draft angle. Hence the tooling direction is created by considering the above factor and bisecting method is used. The base surface of the class – A was extracted…
30 Nov 2022 01:53 PM IST
Week 8 - Challenge 3 - Coin Holder Design
TOOLING AXIS:- Considering the Ejection from the cavity of the mould after manufacturing the interior trim (switch bezel) must have the nominal 3-degree draft angle. Hence the tooling direction is created by considering the above factor and bisecting method is used. The base surface of the class – A was extracted…
30 Nov 2022 03:36 AM IST
Week 8 - Challenge 1 - Base Bracket Design
TOOLING AXIS:- Considering the Ejection from the cavity of the mould after manufacturing the interior trim (switch bezel) must have the nominal 3-degree draft angle. Hence the tooling direction is created by considering the above factor and bisecting method is used. The base surface of the class – A was extracted and…
28 Nov 2022 12:57 PM IST
Week 8 - Challenge 2 - Switch Bezel Design
TOOLING AXIS:- Considering the Ejection from the cavity of the mould after manufacturing the interior trim (switch bezel) must have the nominal 3-degree draft angle. Hence the tooling direction is created by considering the above factor and bisecting method is used. The base surface of the class – A…
28 Nov 2022 12:57 PM IST