Week 8 - Challenge 4 - Coin Holder Design

AIM

To create the Coin Holder Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.

To Create the Coin Holder plastic component in 2.5 thickness.

OBJECTIVE

• Creating Tooling Axis
• Creating B and C Surface
• Performing Draft analysis in given Class A surface and created plastic component

INTRODUCTION

CLASS A SURFCAE

Class-A is a term used in specifically in automotive design. It describes the final production surface data for the aesthetic parts of the car.

CLASS B SURFACE

The Class B finish is a quality finish with only minimal imperfections. A Class B finish is the most common finish for exterior surfaces. It is normally specified on surfaces such as external covers, panels, and parts that are fairly prominent.

CLASS C SURFACE

The Class C finish allows more imperfections than Class A or B. Class C is often specified for interior surfaces not readily visible, surfaces that will be covered by another part when assembled, or surfaces which the Customer feels do not need to meet a high cosmetic finish.

PROCEDURES

Draft Analysis

The draft analysis will helps you quickly gather the draft angle on multiple surfaces without the need for tedious manual measurements. Here is a quick rundown of how the icon works when you have a given die direction.

First, we need to create a tooling axis for performing a Draft Analysis.

Basicaly we need two bisecting lines from X and Y Direction to create a tooling axis, but here dont need bisecting lines because the base of coin holder is flat surface.So we create tooling directly from the surface with respect to poin and Axis system.

Here we generate tooling axis form the base surface of given component with using extract tool.

Now we go to insert< analysis< draft analysis and follow usual procedure to do the analysis.

Align the compass and click on the surface and as expected the model is mostly in red color i.e. negative draft with respect to the axis.

To correct it to as best as we can we moved the compass a bit till we got most of the surfaces in green and lock that position.

After hitting ok, we change the direction of the line from z axis to compass direction. The axis will align itself accordingly.

CREATING B SURFACE.

Now create the Plastic design for the given Class A surface of the Center Console Coin Holder by creating the Class B and C surfaces.

Create a Geometrical set in a tree and name it.Extract the side wall surface of the Center Console Coin Holder by Extract option by selecting the face.Select the faces.

Untrim the extracted surface using the Untrim option by selecting the surfaces.

Extrapolate the Untrimmed surfaces using the Extrapolate option.In Extrapolate Definition: Boundaries - select the edge of the Untrim surface and Extrapolate - untrimmed surface and offset the surfaces to 2.5mm in the opposite direction to the Class A surface

Extract the base surface and block and do the same process and offset the surface to a distance of 2.5mm in downward direction.

Trim the Excess portion of the surfaces using the trim option.

Do the same process for inclined walls surface and outside wall surface by extracting and offsetting the surface and trim the component.

Add the fillets at the wall's edges.

Next, extract the flange surface of the A surface which highlight in brown and yellow color in A Surface and then using Multiple extract option to extract of the surfaces. Offset with 2.5 mm in inner direction.

Extrapoate the edges for easy to trimming and finnaly in the B surface trim all the face which create base, block and flanges.

This is the B Surface which created from A surface with given edge fillets in orders to A surface fillets.

CREATING C SURFACE:

Create the class C surface for class A surface by using the Multi extract option by selecting the boundaries.Create a smooth curve for the extracted boundary.Select the extracted boundary.

Extract the outer boundary walls and Replace the Multi extract boundary with the Smooth curve.

Now using the Sweep option create the C surface by selecting the Subtype as - with reference surface and Guide curve as - Boundary which is extracted and Reference surface as - Extracted boundary surface.

Join the surfaces with Class A and Class C using Join tool option.

Check for any open boundaries in Plastic design and create the solid surface for the design in Part design using a closed surface option.

Insometric and Orthograpic view of Plastic component

Now do the draft analysis for the solid component tooling axis and check for the draft angle as it should be in green in colour in the tooling axis.

FINAL BODY

By using tool Close surface tool to change the part solid body.

TREE STRUCTURES

CONCLUSION

Here, we created the Part component from the given Class A Surface of Coin Holder Design and performed the draft analysis with respect to the tooling axis in the proper tree structures.