Week 8 - Challenge 2 - Base Bracket Design

1).

FIRST WE SHOULD CREATE A POINT AND THEN ONE DUMMY AXIS AND INTERSECTING LINE OR (BOUNDARY) WITH THE CLASS A SURFACE

THEN FROM INTERSECTING LINE, WE CREATED TO TWO LINES WITH POINT TO POINT AXIS AND THEN WE CREATED ONE TOOLING AXIS

AFTER CREATING THE TOOLING AXIS WE INSERTED THE BASE BRACKET AND IN-BRACE BRACKET WE INSERTED THE CLASS B SURFACE.

IN CLASS B SURFACE WE INSERTED RIB 1. FROM THE CLASS A SURFACE WE EXTRACTED ONE SIDE OF THE RIB .(I.E. RIB 1)

AFTER EXTRACTING THE RIB 1 WE UNTRIMMED THE MULTIPLE EXTRACT

AFTER THE SURFACE ANTRIM WE EXTRAPLOTED THE UNTRIM SURFACES SO THAT WE CAN TRIM AND CREATE THE RIB 1

AFTER TRIMMING THE EXTRAPOLATE SURFACES WE AN AN RIB AND WE OFFSET THE RIB DOWN WITH 2.5 MM AND APPLIED COLOUR TO RIB SO THAT WE CANT GET CONFUSED

AFTER CREATING 2 RIBS WE INSERTED A GEOMETRICAL SET AS BASE SURFACE 1. IN THIS BASE SURFACE WE EXTRACTED THE BASE FROM THE CLASS A SURFACE

FROM THE CLASS SURFACE WE EXTRACT AND EXTRAPLOTED THE BASE SURFACE AMF WE OFFSET WITH 2.5 MM DOWN

WE INSERTED A GEOMETRICAL SET AS FINAL TRIM IN CLASS B SURFACE AND WE TRIMMED THE BOTH RIBS WITH BASE AND SURFACE

AFTER THE FINAL TRIM WE INSERTED A GEOMETRICAL SET AS CLASS C SURFACE WE CREATED THE BOUNDARY OF THE CLASS A SURFACE

AFTER THIS WE SWEEP THE BOUNDARY OF THE CLASS A SURFACE AS SHOWN IN THE BELOW IMAGE

IN THE BELOW FIGURE WE CREATED THE BOUNDARY OF THE HOLES OF SURFACE A AND WE SEEP THE HOLES BOUNDARY

WE JOINED THE SWEEP AND CLASS A SURFACE

IN THIS WE TRIMMED THE SURFACE JOIN WITH CLASS B SURFACE

IN PART BODY WE CREATED THE SOLID BODY OF THE FACES TRIM BY CLOSE SURFACE

DRAFT ANALYSIS AT 3 DEGREES

DRAFT ANALYSIS WITH 2.5 DEGREES

DRAFT ANALYSIS OF THE BRACE BRACKET IN Z DIRECTION

DRAFT ANALYSIS OF THE BRACE BRACKET IN Y DIRECTION

DRAFT ANALYSIS OF THE BRACE BRACKET IN X DIRECTION

TREE STRUCTURE

ISOMETRIC,FRONT,SIDE TOP VIEWS

FIRST WE SHOULD CREATE A POINT AND THEN ONE DUMMY AXIS AND INTERSECTING LINE OR (BOUNDARY) WITH THE CLASS A SURFACE.

THEN FROM INTERSECTING LINE, WE CREATED TO TWO LINES WITH POINT TO POINT AXIS, AND THEN WE CREATED ONE TOOLING AXIS.

AFTER CREATING THE TOOLING AXIS WE INSERTED A GEOMETRICAL SET AS A BASE BRACKET AND IN-BRACE BRACKET WE INSERTED A GEOMETRICAL SET AS A CLASS B SURFACE.

IN CLASS B SURFACE WE INSERTED RIB 1. FROM THE CLASS A SURFACE WE EXTRACTED ONE SIDE OF THE RIB. (I.E. RIB 1).

AFTER TRIMMING THE EXTRAPOLATE SURFACES WE WILL GET A RIB AND WE OFFSET THE RIB DOWN BY 2.5 MM AND APPLIED COLOUR TO THE RIB SO THAT WE CANT GET CONFUSED. AFTER CREATING 2 RIBS WE INSERTED A GEOMETRICAL SET AS BASE SURFACE 1. IN THIS BASE SURFACE WE EXTRACTED THE BASE FROM THE CLASS A SURFACE.

WE INSERTED A GEOMETRICAL SET AS THE FINAL TRIM IN THE CLASS B SURFACE AND WE TRIMMED THE BOTH RIBS WITH BASE AND SURFACE.

AFTER THE FINAL TRIM WE INSERTED A GEOMETRICAL SET AS CLASS C SURFACE WE CREATED THE BOUNDARY OF THE CLASS A SURFACE.

THEN WE CREATED THE BOUNDARY OF THE HOLES OF SURFACE A AND WE SEEP THE HOLES BOUNDARY.

WE JOINED THE SWEEP AND CLASS A SURFACE.

IN THIS WE TRIMMED THE SURFACE JOINED WITH CLASS B SURFACE.IN PART BODY WE CREATED THE SOLID BODY OF THE FACES TRIM BY CLOSE SURFACE

THEN WE DID A DRAFT ANALYSIS AT 3 DEGREES AND WITH 2.5 DEGREES