Week 8 - Challenge 1 - Base Bracket Design

  Q1. Flatten the harness assembly completed in the “ week 4 challenge”. Place the flattened view on the drawing sheet. Ensure bundles with protective coverings has different visuals on the drawing view. AIM- To prepare a flattened view of a previously created harness assembly OBJECTIVE- The…

AIM: To design two seperate wiring harness assymblies and to connect them together to give another product. we have provided the harness layout as below and accordingly we have to route it. For that we have to make assumption for harness bundle diameters and use DT connectors. PROCEDURE: Step 1:  We have to first…

AIM: 1) To route the following harness layout in Electrical workbench.          2) To add protective covering on all branches connected to DT06-2S & DT06-4S connectors.                                    …

Aim: Download following connectors & Connector clip cad data from given link & define it as Electrical Connector using Electrical Part design Workbench. Define all the necessary properties to Connectors & Clip.  Deutsch DT06 – 08SA ( https://www.te.com/usa-en/product-DT06-08SA.html) Tyco 174357-2…

 Wiring harness routing & packaging Rules Week 3 Challenge Q1. Download following clip cad data & define it as Electrical support using Electrical Part design Workbench. Define all the necessary properties. P CLAMP   The given clip was downloaded and opened as a part file. I have to define two points…

Underbody Coating  Underbody Coating is a sprayable coating, which protects the under surface of the vehicle from corrosion. Underbody coating provides long term protection from corrosion to car's underbody. It also protects parts like internal body panels, frame rails and other inner cavities that are not…

AIM: DETAILED REPORT ON BENCHMARKING To prepare a report explaining what is Bench-marking , Compare at least 4 Vehicles and Provide a Preoper conclusion for the report ,suggesting a suitable vehicle among the comparison made. WHAT IS BENCHMARKING ? It is the process of comparing one's business process and performance…

DESIGNING A PILLAR USING MASTER SECTION OBJECTIVES To improvise the Class A surface by resolving bad patches and adding flanges to it.  To create A pillar solid model with the help of  improvised class A surface. To create B side features for the A Pillar using the master section given to us as an input. To create…

DESIGNING A PILLAR USING MASTER SECTION   INTRODUCTION  MASTER SECTION: Master sections development takes place during feasibility check and concept validation stages of the product life cycle. These are typically the guides for design requirements and which decides the component packaging after the development…

                                                                           AIM:  Attachment Feature Creation (Ribs &…

   BUMPER DESIGN AIM: to make a model from the provided class-A surface.INTRODUCTION:CLASS-A SURFACE: a surface made by the designer which is given as an input to the plastic modeler to work on. It is aesthetic surfaceand the outer most surface.CLASS-B SURFACE: a surface below a certain thickness…

AIM : Create the Core and cavity blocks for the switch bezel designed in the earlier challenge.    PLASTIC COMPONENT : Switch Bezel Design TREE STRUCTURE   FINAL PART ISOLATED VIEW TOP VIEW SIDE VIEW TOP VIEW DRAFT ANALYSIS OF CLASS A SURFACE DRAFT ANALYSIS OF FINAL PLASTIC COMPONENT …

Introduction: Draft Analysis is the process of assessing the designed plastic part if it has the drafting angles as per the requirement. In CATIA, draft analysis is done by the tool called Feature Draft Analysis. It shows the different draft angles available at different parts and says if it meets the requirement or not…

PLASTIC COMPONENT : Switch Bezel Design TREE STRUCTURE   FINAL PART ISOLATED VIEW TOP VIEW SIDE VIEW TOP VIEW DRAFT ANALYSIS OF CLASS A SURFACE DRAFT ANALYSIS OF FINAL PLASTIC COMPONENT    FINAL PART DRAFT ANALYSIS ISOLATED VIEW FRONT VIEW SIDE VIEW TOP VIEW  

  PLASTIC COMPONENT: Base Bracket Design MODEL TREE:   FRONT VIEW:   ISOMETRIC VIEW:   SIDE VIEW:   TOP VIEW:   COLOR VARIANT OF DRAFT ANALYSIS:   DRAFT ANALYSIS OF CLASS-A SURFACE:   DRAFT ANALYSIS OF PLASTIC COMPONENT:   SOLID MODEL: DRAFT ANALYSIS: