Week 7 Challenge - Assembly Workbench

BUTTERFLY VALVE ASSEMBLY: After designing every component. we have created the final assembly model using SIEMENS NX CAD. MODEL VIEWS: FRONT VIEW           TOP VIEW           SIDE VIEW           ISOMETRIC VIEW          …

AIM: To design the back door of the car and  make the inner panel for the back door and also design the necessary re-enforcements. SOFTWARE: NX 12.0 INTRODUCTION : The trunk (North American English) or boot (British English) of a car is the vehicle's main storage or cargo compartment, often a hatch at the rear…

Aim  To calculate the section modulus of the previously designed hood for analyzing its strength and also optimizing the design to see the difference in the bending strength of the hood. Higher the section modulus of a structure, the more the resistive it becomes to bending. Section modulus Section modulus is a geometric…

AIM: The main objective of the project is to create the Roof Sheetmetal design in NX cad, and also designing Front roof rail, rear roof rail, bow roof front, bow roof rear, center roof rail and Reinforcement are creating to build the strong roof these are all create by using nx cad. Objective: Do curvature study on Roof…

FENDER DESIGN:- Objective is to:- 1. Design Drip Area, 2. Design Sill Mount Area 3. Design Body Mount Area 4. Design Bumper Mount Region and A-pillar mount Region. INPUT FROM STYLING TEAM:- A Class Surface   1. DESIGN OF DRIP AREA:- Master sections to follow to create the Drip Area   Creating Drip Area : DESIGN OF SILL…

     AIM:   To design the car hood and understand the mechanism behind the design of hood, then development& its safety features as per the design consideration. The following task is performed: Design Outer Panel with the Hem Develop the Inner Panel Develop all the Necessary Reinforcements Mirror and position the Hinge…

AIM: To develop the Door Trim panel OBJECTIVE: Creation of CAD model considering following inputs as like in OEM and tier1 companies a) Class A surface b) Nominal thickness : Refer master sections c) Attachment strategy :  Find a attachment strategy for the door panel complete work. Use Push pin with Dog house for Lower…

AIM : To create A pillar plastic component using Class A surface. OBJECTIVES : To check continuity of Class A surface. To create a tooling direction. To perform draft analysis of the plastic component. To create Class B and Class C surface using Class A surface and make a closed Body.  To create Dog House considering the…

Aim : To A Create the DOOR TRIM LOWER Plastic component through the given Class-A surface.  Also Create the Heat Stakes and the locators considering the design rules mentioned in the video for the door applique.      Objectives : To begin with, the tooling axis for the given Class-A Surface should be created meeting the…

Aim: Create the Dog House for the Door Trim considering the design rules and perform the draft analysis for class A and create the final close body component and perform the draft analysis. Objective: Create the Tooling axis  Design the class-B and class-C surfaces and join them. Use the Close Surface feature to make a…

AIM: To Create the Door Handle Component from the given Class-A surface. Create the tooling axis for the given Class-A Surface meeting the requirements of the draft angle.Attach B side Features in the component. perform the Draft analysis on the model.  Procedure for the projects Creating the tooling axis Draft analysis…

AIM : To create the bumper design plastic component through the give class a surface. create the tooling axis for the give class a surface  by meeting the requirement of the draft angle and at the end perform the draft analysis on the model  INPUT GIVEN : To create the bumper design plastic component through the offset…

OBJECTIVE   The objective of the design the switch bezel and to do a draft analysis for it by creating the required tooling direction with the help of Bisecting method. DESIGN CONSIDERATION  Class – A surface should be aesthetically smooth and good. Class – B surface should have all the supporting…

                Objective : Create B-class surface, C-class surface, and the tooling axis for the given Base bracket model. To publish class-A surface, B-class surface, C-class surface, and the tooling axis Performing draft analysis to verify the creation of the Tooling…

  EXPLAINATION FOR QUICK-RETURN MECHANISM ASSEMBLY First all components are imported into the assembly workbench. I have fixed the first component to take it as referance element. Now coincidence relation is given between part5 and part1. Coincidence relation is given between the plane of fixed part and part4. Offset…