Week 14 challenge

1.Body in white (BIW) is the stage in automobile manufacturing in which a car body's frame has been joined together, that is before painting and before the motor, chassis sub-assemblies, or trim (glass, door locks/handles, seats, upholstery, electronics, etc.) have been integrated into the structure. Assembly involves…

AIM  Route the Wiring harness on Given car body and Prepare flatten view drawing in CATIA V5. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design. Apply Protection coverings as required. Given car back door cad data           …

 AIM  Route the Wiring harness on Given Engine and Prepare flatten view drawing in CATIA V5. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design. Apply Protection coverings as required. ENGINE WIRING HARNESS ROUTING                                         …

AIM: TO FLATTEN THE WIRING HARNESS AND DRAFT THE WIRING HARNESS ASSEMBLY. GIVEN: HARNESS ASSEMBLY: HARNESS FLATTENING: WE GO TO THE HARNESS FLATTENING WORKBENCH AND DEFINE THE FLATTENING PARAMETERS. WE USE THE EXTRACT COMMAND TO BRING THE HARNESS ASSEMBLY TO THE FLATTENING WORKBENCH HERE. CHOOSING A SUITABLE PLANE WE FLATTEN…

The objective of this project is to first route the two Harness A and Harness B as per the given harness layout. Figure 1: Shows the layout of two Harness A and Harness B The electrical connectors are represented by numbers in the above figure. There are 8 different types of connectors at 10 different locations.     2.…

Aim:  1) To Route the following harness layout in the Electrical workbench. 2) Add protective covering on all branches connected to DT06-2S & DT06-4S connectors. Given: CAD data of the following Connectors:  DT06-4S DT06-6S DT06-2S DT06-08SA Connectors Layout Design:       Steps to be followed: 1. Download connector 3D…

1.P clamp The given clip was downloaded and opened as a part file. I have to define two points that will be used as entry and exit points. Then a plane has to be defined at the points. A base plane has to be defined at a distance of 2 to 3 mm from the clip. again we define the exit point at the first definition as the…

  1.Deutsch DT06 - 08SA THE CONNECTOR IS FIRST UPLOADED IN THE PART DESIGN WORKBENCH  WE DEFINE THE POINTS FOR CONNECTOR CONNECTION AND BUNDLE CONNECTION. THE AXIS SYSTEMS ARE PLACED ON THE CONNECTOR CONNECTION AND CAVITY CONNECTION POINTS THE ORIENTATION OF THE AXIS SYSTEM IS NOT SPECIFIC, WE JUST NEED…

AIM:- Assemble and apply GD&T to the butterfly valve assembly drawing. Introduction A Butterfly valve is a quarter-turn rotational motion valve, that is used to stop, regulate, and start a flow. Butterfly valves are easy and fast to open. A 90° rotation of the handle provides a complete closure or opening…

AIM: To design the back door of the carr and  make the inner panel for the back door and also design the necessary re-enforcements.     Introduction: An automobile back door or Tailgate is the panel that covers the boot (or trunk) of an automobile. It enables access to the main luggage compartment.…

INTRODUCTION  The roof of a car or other vehicle is the top part of it, which protects passengers or goods from the weather. The roof also protects the passenger from any injury when the car gets crashed or is rolled over or something heavy falls on the roof. OBJECTIVE The mian objective of…

 Design a Fender Model with the necessary mounting with a given class A surafce. FENDER The fender acts as a housing for the wheel and protects everything else by keeping the dirt and debris contained within the curved enclosure. This prevents the particles from spewing or damaging car parts on the car’s…

Main objective of the project is to calculate the Wheel arch area, and also conclude, If the car will pass the European standards or not. Because of countries are follow the different regulation. Wheel Arch is the semi-circular part of thee fender positioned above the wheel of the vehicle. The design of Wheel arch of a…

For Hood Design Section modules: Section modulus is the ratio of bending to the farthest fiber from neutral axis, or it is the measure of the strength of the beam. Ratio of Area Moment of Inertia to the Distance from the Neutral Axis to the Point where the Bending Normal Stress is determined. Section modulus (S) = I/Y…

AIM To create a door interior part from the inputs of class A surface along with master section by following the design rules followed in tier 1 and OEM industries in catia v5.   OBJECTIVES Create a sketch by using Positioned sketch All the should be sketches should be Iso-Constrained Ensured Proper Tree Structure Geometrical…

 To design a Hood outer panel, inner panel and the necessary reinforcements by the given Master section and design parameters. Hood is a main component of front portion of a car. It is an opening body panel that covers the engine in front engine vehicle. It consist of an outer panel and inner panel. The inner panel…

A car’s underbody is exposed to the most wear and tear caused by muddy water, potholed roads, stones and other obstacles on the road. Because it’s not in plain sight, we often do not see the damage. Underbody Treatments offers you a long term solution for issues related to corrosion and rust. First, the car…

 01. Suggested Cars Listed Below:-  Tata Nexon Hyundai Grand i10 Nios Citroen C3 Kia Sonet Honda Amaze   02.Mechanical Characteristics of Cars: Advance BIW Design and Lightweight of Carbody Smoot Operating Device BS6 Engine Use in cars Good Settings Arrangements Good Mileage of Cars Good NVH Smoot Operating…