Week 10 - Challenge 1- Attachment Feature Creation (Ribs & Screw Boss)

AIM: TO FLATTEN THE WIRING HARNESS AND DRAFT THE WIRING HARNESS ASSEMBLY. HARNESS FLATTENING: WE GO TO THE HARNESS FLATTENING WORKBENCH AND DEFINE THE FLATTENING PARAMETERS. WE USE THE EXTRACT COMMAND TO BRING THE HARNESS ASSEMBLY TO THE FLATTENING WORKBENCH HERE. CHOOSING A SUITABLE PLANE WE FLATTEN THE HARNESS ASSEMBLY.…

modelling Week 5 & 6 Challenge Aim: Route two electrical harnesses per the given layout and interconnect them as a single harness assembly check for bundle continuity, and bundle warnings, and then provide annotations for the final harness assembly. Objective: The objective of this project is to first route the two Harness…

Aim:  1) To Route the following harness layout in the Electrical workbench. 2) Add protective covering on all branches connected to DT06-2S & DT06-4S connectors. Given: CAD data of the following Connectors:  DT06-4S DT06-6S DT06-2S DT06-08SA Steps to be followed: 1. Download connector 3D data from www.te.com DT06-4S DT06-6S…

Q1. Download following clip cad data & define it as Electrical support using Electrical Part design Workbench. Define all the necessary properties. process:   Create two points one as entry and another as exit point. create planes at two points and another at base. Switch to Electric part desgn Click on support defination…

Each part has been defined as a Electrical component. Both the connectors has been defined with a bundle connection point and connector connection point and also with the cavity connection point   Cavity connection point is given to connect the clip  After connecting the both parts all the parts are added in to the catalouge …

Objective The objective of this project is to model a butterfly valve and apply GD&T to the different parts and assembly of the butterfly valve.  Introduction A Butterfly valve is a quarter-turn rotational motion valve, that is used to stop, regulate, and start a flow. Butterfly valves are easy and fast to open.…

1.0 AIM Use the provided styling surface to come up with a back door design, use appropriate design methodologies, and provide the necessary reinforcements and embosses 2.0 INTRODUCTION 2.1 BACK DOOR Back door or tail gate simply refers to the back of the car that can open and close.it covering the rear of the vehicle.It…

ROOF DESIGN  Objective: For a given roof styling Come up with a design of the roof and its various components such as front roof rail, Bow roofs, and rear roof rail provide it with essential reinforcements and flanges required. To perform a curvature study on the given styling to decide the positions of bow roofs,…

FENDER: Fender is apart of vehicle that surrounds the wheel. It prevents debris, water, small stones, mud from entering the engine compartment or someone getting hit by a stone and also it is an exterior aesthetic part. There are two types of fenders: 1.) full bumper type.                                                   …

FENDER DESIGN REGULATIONS AND REPORT OF WHEEL ARCH AND REFERNCE IMAGES ALL ARE MENTIONES IN ZIP FILE 

Section Modulus: Ratio of Moment of inertia at the neutral axis to the farthest point from neutral axis  It gives the strength of the hood based on the intersection given at midpoint  So, in the given zip file i have mentioned intersections at different lengths having diiferent moment of inertia. Higher the minimum…

Created Hood inner Panel taking reference from the outer panel and created all features like Emboss,Heinforcement, Hinges, Mastic Points, Strikker Hood is what we call as a frontal car door(bonnet) which covers housing of  engine, battery, etc.   Inner panel of the hood is created with the master section…

Report down in the submission box in pdf format

Benchmarking: It is also called as a Comparison. That is, if we are developing a product, we go through a lot of research of that product design having manufactured by the other company or competitor taking all the pros and cons of their design and compare it with our product and increase our sales by working on that cons…

NOMINAL THICKNESS: 2.5MM LOWER SUBSTRATE IS FIXED CONSTARINT PUSH PIN IS PLACED ON THE DOG HOUSE WIHT AXIS & POINT CONSTRAINT, CONTACT CONSTRAINT FEATURE: 1) DOG HOSE                 2) HEATSTAKES                 3) LOCATERS DOG HOUSE:…

TOOLING AXIS: IT IS CREATED WITH THE HELP OF MASTER SECTION WHERE I CREATED THE POINTS ON THE MASTER SECTION AND DRAWN POINT-POINT TO LINE ON THE BOTH SIDES OF THE DOG HOUSE AND THEN USED THE BISECTING LINE TO CREATE THE TOOLING AXIS  SIDE CORE AXIS: IT IS CREATED WITH THE HELP OF TOOLING AIXS ON WHICH I CREATED A…

TOLLING AXIS IS CREATED BY OBSERVING FROM ALL THE DIRECTIONS X,Y.Z AND CHOOSE THE BEST POSSIABLE DIRECTION FOR SURFACE TO CLEAR. IN OUR CASE THE CLASS A SURFACE IS CLEARING IN Y-AXIS AND CHOOSE THAT AS A TOOLING AXIS AND THEN DRAFT ANALYSIS IS PERFORMED ON THE SURFACE USING TOOLING AXIS TO SEE THE SURFACE DRAFTING ANGLE…

 TOOLING AXIS: FIRST, THE CLASS A SURFACE IS OBSERVED IN EVERY DIRECTION TO OBSERVE THE CLEARANCE AND THEN CREATING A INTERSECTION OF THE AXIS TO CREATE A TOOLING AXIS AND THEN ADDING A POINT TO THE THE TOOLING AXIS TO CREATE A LINE FOR SIDE CORE AXIS IN THE DIRECTION IN WHICH THE DOG HOUSE IS OPEN  DRAFT ANALYSIS…

ASSIGNMENT SUBMITED

SORRY FOR THE LATE SUBMISSION. IT IS BECAUSE I WAS USING A OLDER VERSION OF CATIA SOFTGWARE HENCE PROBLEM ARISED WHILE EXTRAPOLATING SO I HAD TO ASK MY RELATION SHIP MANAGER FO THE SOFTWARE AND IT TOOK TIME FOR THEM TO RESPOND BACK AND TO PROVIDE SOFTWARE.

1.) TOOLING AXIS IS CREATED BASED ON THE HELP OF SECTION VIEW IN POSITIONED SKETECH AND DRQWING THE LINES TO GET THE BISECTING LINE-1, NEXT SINCE IT HAS THREE WALLS FOR LINE 2 WE DO SAME PROCEDURE AS LINE 1 BUT WWE WILL DRAW A DUMMY BISECTING LINE HAVING A ANGLE 0F 3 DEGREES WITH THE LINE DRAWN USING 3RD WALL. AND THEN…

1.)DRAFT ANALYSIS IS DONE ON THE CLASS A SURFACE FOR DRAFT ANGLE AND ALSO DONE ON THE FINAL PLASTIC PRODUCT FOR THE PRODUCT VALIDATION AND THAT HAS BEEN ATTACHED IN THE ZIP FILE WITH THE COLOUR CONTRAST 2.) TOOLING AXIS IS FOUND OUT ON THE CLASS A SURFACE FOR THE PRODUCT. SO THAT THE PRODUCT CAN BE EASILY REMOVED AFTER…

Assignment Submitted