Project 2 - SiC/IGBT isolated gate driver reference design with thermal diode and sensing FET

Aim: For EV_defaults_in file, if cargo mass is 500 kg with all other default conditions, can the vehicle travel for 45 km with FTP drive cycle? Conclude your observations. Considering the case for an typical EV, lets simulate EV_defaults_in, an electric vehicle with following specifications: In the above example, a battery…

Using MATLAB/Simulink and  the drive cycle from the attached Excel sheet, find- The max heat generation of the battery  The SOC of the battery at 2 *104second of the battery operation Time Time Step Battery Current 00:00.4 0.1 -0.9632 00:00.5 0.2 -0.952 00:00.6 0.3 -0.9072 00:00.7 0.4 -0.9632 00:00.8 0.5 -1.0304…

  1. Design a battery pack for a car of roughly 150 Kw with 120 V. Use a 3500 mAh 3.6V nominal NMC chemistry cell. a.Design the battery pack configuration.    Cell Specifications: Nominal Voltage= 3.6V Max. Voltage= 4.2V Nominal cell capacity= 3500mAh = 3.5 Ah Rated power=150kw Rated voltage=120v First finding…

An electric rickshaw is a three-wheeled vehicle that is powered by an electric motor and battery. Electric rickshaws are becoming increasingly popular in many parts of the world as a more environmentally friendly and cost-effective alternative to traditional gasoline-powered rickshaws. Electric rickshaws come in various…

Create a MATLAB model of electric car which uses lithium ion battery and suitable motor. Choose suitable blocks from Simscape or Powertrain block set. Implement the vehicle speed control using PI controller and generate brake and accelerator commands. Avoid using readymade driver block for speed control. Objectives To…

Designing an IGBT or SiC isolated gate driver power stage with advanced protection features requires a thorough understanding of the system requirements, as well as the properties and limitations of the components being used. The power stage should support a single phase from a traction inverter and provide a high level…

How will you decide the layer stack up. The PCB Stackup Design Perspective Regardless of the number of layers that comprise your board design, specifications for pad spacing, clearances, trace widths, copper weights and drill hole sizes must be tailored to your contract manufacturer (CM). If your design requires multiple…

Create a MATLAB model of electric car which uses a battery and a DC motor. Choose suitable blocks from Powertrain block set. Prepare a report about your model including following: Objectives:  System level configurations Model parameters Results Conclusion Aim: To develop the MATLAB and Simulink model of electric…

part A 1.ans Aim: to Search and list out the total weight of various types of aircrafts.  Typical Airplane Weights Aircraft Empty Weight Max Fuel Weight Max Cargo Weight Max Gross Takeoff Weight Antanov AN-225 628,000 lbs285,000 kg 661,400 lbs300,000 kg 417,000 lbs190,000 kg 1,411,000 lbs640,000 kg Airbus A380-800…

The braking performance is one of the most important concerns in vehicle safety. In urban area driving, a significant amount of energy is consumed in braking. Electrification of vehicles makes it feasible to recover some of the energy lost in braking. A hybrid braking system was developed to ensure the efficient braking…

1a ans  Aim: To Explain a MATLAB demo model named ‘Speed control of a DC motor using BJT H-bridge This example shows the simulation of an H-bridge used to generate a chopped voltage and to control the speed of a DC motor. Gilbert Sybille (Hydro-Quebec)   Description The Bipolar Junction Transistor (BJT)…

1. Which types of power converter circuits are employed in electric and hybrid electric vehicle?  Answer: Difference between electric vehicle and hybrid electric vehicle: Specifications Hybrid Cars Electric Cars Power/Fuel Source Electricity and Fossil Fuel (Petrol and Diesel) Electricity Through Battery Pack (DC) Engine…

1.ans 1 mapped model of engine  dynamic model of engine  2 Mapped engines represent macro engine behaviour as a set of lookup tables(brake torque,fuel flow,air masflow,exhaust temperature,efficiency and emissions) as functions of commanded load and measured engine speed.   Dynamic engine decompose engine…

Aim: To design a Simulink model for the DC motor  shown in Figure 1. amd aslo by Using  the Proportional, Integral, and Derivative (PID) control design knowledge gained in the training to design, develop and test a controller to maintain a desired speed for the motor. The Project is based on speed control…

project: To he excel file in the Matlab program and perform the interpolation in the range of -17.3:0.1:0.9. Generate the interactive plot for the interpolated data and store them in a text file. Matlab progarm: from the beginning need to import the exel file to matlab.  ------------xxxxxxxxxxxxxx-------------…