Project 2

AIM To create a door interior part from the inputs of class A surface along with master section by following the design rules followed in tier 1 and OEM industries in catia v5 SOFTWARE USED CATIA V5 OBJECTIVES Create a sketch by using Positioned sketch All the should be sketches should be Iso-Constrained Ensured Proper…

Aim      Route the Wiring Harness on given Car body and prepare flatten view drawing in Catia V5 Objective      The objective of this project is to route the wiring harness and prepare flatten view drawing for the tailgate of the car. All types of packaging rules have to be considered while routing the harness and industry…

Aim     To route the wiring harness on given Engine and flatten view drawing in CATIA V5. Objective      The objective of the project is to route the wiring harness on given Bugatti V16 Engine and prepare flatten view drawing in CATIA V5. All types of packaging rules have to be considered while routing the harness. Also,…

Aim: Route two electrical harnesses per the given layout and interconnect them as a single harness assembly check for bundle continuity, and bundle warnings, and then provide annotations for the final harness assembly. Objective: The objective of this project is to first route the two Harness A and Harness B as per the…

AIM: TO FLATTEN THE WIRING HARNESS AND DRAFT THE WIRING HARNESS ASSEMBLY. GIVEN: OUTPUT ASSEMBLY FLATTEN DRAFTING

Aim:  1) To Route the following harness layout in the Electrical workbench. 2) Add protective covering on all branches connected to DT06-2S & DT06-4S connectors. Given: CAD data of the following Connectors:  DT06-4S DT06-6S DT06-2S DT06-08SA Connectors Layout Design: Steps to be followed: 1. Download…

P-Clamp: This is another important component of the wiring harness which should be defined before wiring harness routing. Following are the important parameters that are required to be defined: Entry point and plane, Base plane and Exit plane.   Defining clamp as support part. Clip has two entry points and two…

AIM:      Download following connectors & Connector clip cad data from given link & define it as Electrical Connector using Electrical Part design Workbench. Define all the necessary properties to Connectors & Clip.    Important workbenches in CATIA V5. the important workbenches that…

Objective: The objective of this project is to design the assembly of the Butterfly valve and apply the GD&T concepts to the various parts of the Butterfly Valve. Name of the Parts: 1. Body 2. Shaft-Stem 3. Top Flange 4. Disc Plate 5. Lever Handle 6. Nut COMPONENTS OF BUTTERFLY VALVE Various components of butterfly valve…

BACKDOOR          An automobile back door or Tailgate is the panel that covers the boot (or trunk) of an automobile.         It enables access to the main luggage compartment. A hinge allows the boot lid to be raised, while devices such as springs or gas cylinders hold it up in the open position The Backdoor is an assembly…

HOOD         The hood (North American English) or bonnet (Commonwealth English) is the hinged cover over the engine of motor vehicles. Hoods can open to allow access to the engine compartment, or trunk on rear-engine and some mid-engine vehicles for maintenance and repair. …

ROOF         An automobile roof or car top is the portion of an automobile that sits above the passenger compartment, protecting the vehicle occupants from sun, wind, rain, and other external elements. TYPES OF ROOF Convertible roofs Hardtops. Sunroofs. T-tops. Targa tops. Vinyl…

SECTION MODULUS       Section modulus is a geometric property for a given cross-section used in the design of beams or flexural members. Other geometric properties used in design include area for tension and shear, radius of gyration for compression, and moment of inertia and polar moment of inertia…

FENDER Originally something hung over the side to protect the hull of a ship at a wharf, pier, etc. Of fireplaces since 1680s; of automobiles from 1919. Fender-bender "minor automobile accident" is from 1958. TYPES OF FENDERS Full Bumper type Half Bumper type MOUNTING POINTS OF FENDER A-Pillar Bumper Drip Area Splash Cover…

Checking the surface checking the draft analysis full part body dog house draft analysis full body draft analysis

  GIVEN     Calculate the Wheel Arch gap at required points and check whether the car passes the European standard.                                        SOLUTION      European…

                                                                            BENCHMARKING      Benchmarking is a process…

                                                               UNDER BODY COATING   What is Under Body Coating?          …

ASSEMBLY 2

DRAFT ANALYSIS OF A SURFACE DRAFT ANALYSIS OF PART  PART BODY