Project 2

1)Ans: Main Model: SLDD file:   Requirement Tagging: We can see the Requirement Tagging in Report: Report: JMAAB check: Fixed Point Tool: After the data type will be changed MIL & SIL Functional Test cases:  MIL Harness: Signal Builder Output: Scope Output: Coverage: SIL Harness. At first Build the model…

Answere : Develop the Simulink model based on the given requirements and also create SLDD file and link the same to the model. 1) Aim : Development of TFT Cluster Speedometer Software Component. Basic Information : Cluster Instrument receives the signals from other ECU's via CAN bus interface. It also receives commands…

Esakki Vigneswaran:Live Batch: A): #include <iostream>                                         //header fileusing namespace std;//enum Type{GAS,DIESEL,ELECTRIC};class Vehicle         …

Esakki Vigneswaran:Live Batch A):   #include <iostream>                                                      // header file#include<fstream>       …

Procedure and Steps: The first step is the creation of the Simulink Data Dictionary File from the given calibration and signal data list. Then data dictionary should be linked to the specified simulink model. As per the first requirement, the first subsystem will have three inputs. They are Highway_Input_Signal, Enable_Display,…

Jam Assistant Feature AIM : Model Development of a single feature of Traffic Jam Assist using MATLAB & Simulink as well as Code Generation using Embedded Coder . Objectives : Model Development as per MBD guidelines . Creation of Simulink Data Dictionary . Code Generation using Embedded Coder Generating Model Advisor…

Blocks needed in making simulink model: Battery (Table based) This block models a battery based on tabulated characteristics as functions of state of charge (SOC) and optional temperature (T). Here we made the ports to instrumented and show thermal port. here we made the soc measurment port to yes  And also the thermal…

Battery pack capacity: 18 kWh Cell: ANR26650M1-B  AIM:   This is more power and have high energy than other cells and lower impedance it has high efficiency with more safety precautions also having long life. It has wide range of SOC with less losses which leads to less discharge for long range with lighter…

After opening this file Matlab will ask the following question:- I have selected to Open Project and Model. ANd after that the whole project will be loaded in the Matlab in current folder and workkspace.  After this the BMS_ClosedLoop_Harness_Dashboard model file is open as:-  Block of Model:- Test sequence…

Li-ion Batteries A lithium-ion battery or Li-ion battery is a type of rechargeable battery. Lithium-ion batteries are commonly used for portable electronics and electric vehicles and are growing in popularity for military and aerospace applications. Similar to the lead- and nickel-based architecture, lithium-ion uses a…

SLDD CREATION: The SLDD data files are related to the MATLAB/Simulink. Mathworks Simulink is a multidomain simulation and Model-Based Design for dynamic systems. The SLDD file stores some kind of data used by MATLAB. The following procedure shows how to create and add data to the SLDD file. To create a SLDD file, Open…

#include <avr/io.h>                                                   //we are using I/O registers of AVR#define F_CPU 16000000L               …

#include <avr/io.h>#define F_CPU 8000000UL#include <avr/interrupt.h>#include <util/delay.h>#include <string.h>#include <stdlib.h> #define LCD_Data_Dir DDRD                                       …

Aim: To create a Simulink model of Vehicle Direction Detection as per the Requirement data.   Blocks used: Blocks used to create a model are Input Blocks: To provide the input signals Output Blocks: To send the output signals Constant Blocks: To define the calibration values Logical operator Blocks: AND blocks are…

1)STATIC CODE ANALSIS I HAVE TO UPLOAD TEST MANAGER REPORT 2)INTEGRATION TESTING USING MULTIPLE FILES I HAVE TO UPLOAD THE REPORTS A)I have to upload the reports and B part i have to store the test cases .tcf file and i upload the location image .tcf file stored

Test feature 1: When long pressed the power button of the phone shall switch on with a company logo at the center of the screen. Test feature 2: When the power button is pressed my phone is switched ON and all my icons of the APPS shall be present in the grid. Test feature 3: When the phone is powered ON ,I shall see the…

/* The circuit:- +V connection of the PING))) attached to +5V- GND connection of the PING))) attached to ground- SIG connection of the PING))) attached to digital pin 7// this constant won't change. It's the pin number of the sensor's output:*/const int pingPin = 7; void setup() {// initialize serial communication: Serial.begin(9600);…

//MASTER code:#include<LiquidCrystal.h>                               // Header to use LCD functions#include<Wire.h>                               …

this is the project 2 STATES.H FILE AND .C FILE AND IT WILL SHOW OUTPUT

project1 i have to sumitted the programme and outputalso project 1: #include<stdio.h> #include<stdlib.h> struct list { int P,Q; struct list *next; }; int main() { struct list *A1,*A2,*A3,*B1,*B2,*B3; A1 = malloc(sizeof(struct list)); A2 = malloc(sizeof(struct list)); A3 = malloc(sizeof(struct list)); A1 ->…

AIM: To crate a MATLAB model of an electric car which uses a battery and a DC motor,by choosing suitable blocks from powertrain block set. THEORY:          An electric car is a vehicle that is propelled by one or more electric motors,using energy stored in rechargable battery packs.These are eco-friendly…

AIM:Powertrain for aircraft in runaways Objective: PART A: 1)Introduction: An aircraft is a vehicle that is able to fly by gaining support from the air.it countries the force of gravity by using either static lift or by using the dynamic lift of an airfoil,or in a few cases the downward thruust from jet engines.  …

1)QUESTION: Under the condition of braking,some amount of energy is required to do the same as that of energy required for accelerating the vechile.Hence to calculate energy,we use the acceleration energy equation,                                   Ek=1/2mv^2    Ek=Kinetic energy(J) QUESTION1: The driving cycle taken into…

 First of all, let us understand the basics concept of speed control using H bridge configuration. Most DC motors have two terminals because they are series type (Armature and field windings are connected in series)DC motors. As shown in figure there are two terminals 'A' and 'B' of DC motor.Now if we connect terminal…

Power Converter:  The task of a power converter is to process and control the flow of electric energy by supplying voltages and currents in a form that is optimally suited for user loads. The large number of automobiles in use around the world has caused and continues to cause serious problems of environment and human…

Aim:To study on Powertrain Blockset in MATLAB SOLUTION1: A)Difference between mapped and dynamic model of engine,motor and generator. Powertrrain Blockset provedes two types of engine models:mapped and dynamic.Mapped engines represent macro engine behaviour as a set of lookup tables (brake torque,fuel flow,air mass flow,exaust…

AIM: By using the Advisor tool,we need to simulate the given conditions in MATLAB.   Objective: 1.Load ,EV_defaults_in ,file and change the cargo mass by keeping  all the conditions default with FTP drive cycle and conclude the results. 2.By changing the battery capacity and number of drive cycles.obbserve the…

AIM: To do detailed case study on continuous variable transmission(CVT)using BAJA ATV vechile and present our observvations on it. THEORY: All Terrian Vechile:        An all-terrian vechile(ATV),also known as a quad (cycle),three-wheeler,four-track,four-wheeler,or quadricycle,as defined by the Ameican National Standars…

State flow:Stateflow provides a graphical language that includes state transition diagrams,flow charts,state transition tables,and truth tables.it is used to describe how matlab algorithms and simulink models react to input signals evnts, and time -based conditions.State flow  you model combinational and sequential…

Theory of Dorrbell: 1.The doorbell is a devicehaving mechanical and electrical component produce sound on presing the button. 2.when swith is pressed the circuit loop is completewhich causes the current to flow through the circuit while passing solenoid it generates the electro magnet  Principle Behind Doorbell: solenoid:…