Project 1 - Parsing NASA thermodynamic data

Objective: To simulate the isentropic flow through a quasi 1D subsonic-supersonic nozzle using both the conservation and non-conservation forms of the governing equations and sovle them using the MacCormack's technique and comparing their solutions. Description: We consider the study, isentropic flow…

    Here we are going to understand the concept of the 2d heat conduction equation of both stead and transient state of flow. We need to understand the derivation part where the terms are being discretized sequentially and then we move on to the coding part. There are few things that need to be considered before…

Derivation of the 4th order approximation of the Second-Order Derivative   Using the Central Difference method: Here, we’re computing 4th order approximation at point (i), where we take information from the four-point surrounding (i); i.e. we’re going to take two points on the left of (i) and…

AIM: Perform the heat transfer analysis using ANSYS-Fluent software for the cylindrical 4 by 2 Lithium-ion Battery with heat generation boundary conditions and study the battery thermal management system(BTMS). OBJECTIVES: Do an independent network study for any single case (for speed) and use a more appropriate model…

AIM:  Perform a parametric study on the gate valve simulation by setting the opening from 10 % to 80%. Obtain the mass flow rates at the outlet for each design point. Calculate the flow coefficient and flow factor for each opening and plot the graph. Discuss the results of the mass flow rate and flow coefficient.…

Aim:- To perform analysis on cyclone separator and calculate the separation efficiency and pressure drop.   Objective:- To write a few words about any four empirical models used to calculate the cyclone separator efficiency.  To perform an analysis on a given cyclone separator model by varying the particle…

l. OBJECTIVE To perform steady-state conjugate heat transfer analysis on Graphics Card To find the effect of different velocities on the temperature   ll. INTRODUCTION 1. Conjugate Heat Transfer (CHT) Conjugate heat transfer is defined as the heat transfer between two domains by exchange of thermal energy. For a system…

What are some practical CFD models that have been based on the mathematical analysis of Rayleigh Taylor waves? In your own words, explain how these mathematical models have been adapted for CFD calculations. RT instability is the instability of an interface between two fluids of different densities which occurs when the…

What is CHT Analysis, Why and Where it is used?  Conjugate Heat Transfer (CHT) refers to the coupling of conduction in solids with the convective and radiative heat transfer in the surrounding fluids. In other words, CHT corresponds with the combination of heat transfer in solids and heat transfer in fluids. In solids,…

AIM: Q1. Describe Ahmed's body and its importance. Q2. Explain the reason for the negative pressure in the wake region.  Q3. Explain the significance of the point of separation.    Expected results: 1. Velocity and pressure contours.  2. The drag coefficient plot for a refined case. ( For a velocity…

Objective: Simulate the flow over a cylinder and explain the phenomenon of Karman vortex street.      PART-I Simulate the flow with the steady and unsteady case and calculate the Strouhal Number for Re= 100.  PART-II Calculate the coefficient of drag and lift over a cylinder by setting the Reynolds…

AIM:  For this challenge, we have created two versions of the mixing tee. One of them is longer than the other. Your job is to set up steady-state simulations to compare the mixing effectiveness when the hot inlet temperature is 360C & the Cold inlet is 190C.    objective: Use the k-epsilon and k-omega…

AIM : To plot the T-s and h-s of the rankine cycle by given inputs  EXPLANATION : Fristy write the rankine cycle simulators and write the process of the ranike cycle in the command window and check the xsteam file was reading the processes and now use to read the stae points in the xsteam file and now write the code of…

AIM:To a function that extracts the 14 co-efficients and calculates the enthalpy, entropy and specific heats for all the species in the data file of nasa thermo data file and plot them of every species   EXPLATION: Firstly, we will Input the parameter R and we will open a file THERMO.dat file …

AIM:To find out the stalagmite of glowbal maxima of its function and expalin about the genamatic  algorithm (ga)   EXPLATION: fristly we have write the code of the optimal gobal maxima  and function of the stalagmite code in the another window write the forumlas to slove the stalagmite in the code wise correctly…

AIM:To genarate  the simple pendulum movie animataion   Procedure: write the code and and start the for loop to contact with the ode function code and give requred inputs and wirte the function and and start the new window wirte the simple pendulum code to creat the mivie animation and use the correct inputs…

https://youtu.be/YRzi_LMcALc   AIM:To genarte the 2R forward kinamatics movie avi     PROCEDURE:write the progame about the given video and check the errors like 1l it may be cant able to see like when we type ll or 11 it may causes the error of the prorame and i got the same the error and one more i got…