Project 1 (Mini Project on Vehicle Direction Detection

Build an object-oriented library which can be used to track automobile maintenance. There can be different car types such as petrol, diesel, gas, electric etc., This library should be able to support at least three of the car types.  Maintenance tasks include activities like oil change or replace oil filter, replace…

Overview of the Project: (5 to 6 lines) In this project, controlling the retraction and extension of Airplane’s landing gear can be implemented using Finite State Machine (FSM). FSM is the most efficient algorithm which is mathematical model of computation. 1.Here controlling the retraction and extension of Airplanes…

Aim: Goals (2 to 3 points) Implementation of interface for mathematical Set Theory using C programming. Giving two list of data as input to get the output as union & intersection for given list of data. Key Highlights of the Project: (4 to 5 point) Creating two list of data using linked list method. Insert the node…

Create a Stateflow or Simulink model for the following flowchart. Load the .mat file into the workspace. The input to the model would be the power demand. The output should be: Fuel cell power Battery power FC Operating state (running, standby) Create plot of these outputs against time. (Note- The Simulink model file should…

Create a MATLAB model of electric car which uses a battery and a DC motor. Choose suitable blocks from Powertrain block set. Prepare a report about your model including following: Objectives:         1. System level configurations        2. Model parameters        3. Results        4. Conclusion       Use the "INSERT CODE…

AIM :  Design of an Electric Rickshaw using MATLAB Simulink.   ABSTRACT : In this project, we going to build the MATLAB model of the ELECTRIC RICKHAEW by using a PM brushed type DC motor and a suitable Lithium-Ion battery for the motor. Before that, we will know about what is Electric RICKHAEW, how it's works…

Create a Stateflow or Simulink model for the following flowchart. Load the .mat file into the workspace. The input to the model would be the power demand. The output should be: Fuel cell power Battery power FC Operating state (running, standby) Create plot of these outputs against time. (Note- The Simulink model file should…

Components and supplies 1 Arduino UNO   1 Jumper wires (generic)   1 Arduino UNO   Apps and platforms 1 Arduino IDE   Project description     Introduction In this tutorial I'll show you how can you communicate between two (or more) Arduino boards, using I2C ( Inter-Integrated Circuit) protocol.…

Aim: Overview of the Project:  In this project implementing the Code for “Interfacing a 16*2 LCD with two Arduino’s (one for Master and one for Slave) using Inter-Integrated Circuit (I2C) communication protocol” by sending the message to LCD using I2C communication protocol and display the message…

Create a Stateflow or Simulink model for the following flowchart. Load the .mat file into the workspace. The input to the model would be the power demand. The output should be: Fuel cell power Battery power FC Operating state (running, standby) Create plot of these outputs against time. (Note- The Simulink model file should…

Create a Stateflow or Simulink model for the following flowchart. Load the .mat file into the workspace. The input to the model would be the power demand. The output should be: Fuel cell power Battery power FC Operating state (running, standby) Create plot of these outputs against time. (Note- The Simulink model file should…

Aim: To implement code for “Measuring distance of an object using ultrasonic distance sensor (HC-SR04). Objective: Measuring the distance of an object using Ultrasonic Distance Sensor (HC-SR04) Usage of Input Capture Mode Highlights: Measuring the distance travelled by the wave to the object and gets bounced back…

Project1 Aim: To implement a system on the simulator for controlling a DC motor using L293 motor driver, monitor its status and print the running status of motor on the LCD Display. Objective: Implement a system on simulator for Controlling the DC motor using L293 motor driver. Displaying the running status of DC motor…

Write a Test plan to test features of a new mobile phone (Blackbox test) that needs to be implemented based on the following requirements. (The product is still under development stage and is yet to be UA (User Acceptance ) tested…

Perform Static Code Review Analysis for “C:\**\LDRA_workarea\Examples\C_Testbed_examples\Testrain\Testrain.c” Generate Code review report and upload them.   step 1: start LDRA TBrun. step 2: From the LDRA page select source->single file->LDRA_workarea->examples->C_Testbed_examples->Testrain->Testrain.c->open.(in…

This project is focused on electric vehicle applications using an Induction Motor. The student will have to take the following steps for a successful model: Model 3 Phase Inverter using Simulink (model the parasitic as well) with a switching frequency of 10Khz using 3 phase Squirrel Cage Induction motor, using V/F method,…

Extending the learned lessons in previous module, you will be diving into another power electronics concept on your own. Design of boost converter, and calculating the loss of different components including power switching device and deriving efficiency of boost converter. This is applicable in power supply industry, electric…

OBJECTIVE  MATLAB model of electric car which uses lithium ion battery and suitable motor. System level configurations & Model parameters 1) DRIVE CYCLE we give FTP75 drive cycle to run the model   2) DRIVER  vehicle speed control using PI controller and generate brake and accelerator commands  …

Aim : To Complete the energy management strategy model with battery UC and fuel cell for the positive power and distribute the power demand among these components. and  Set simulation stop time to 598 sec.The output of the model should be the power request from UC, fuel cell and battery. Answer: About Energy…

Q1) Load the UC parameter file. Complete the Ultracapacitor model. Set simulation stop time to 598 sec.The model output should give, current, SOC and Voltage as output   Aim:To model the energy storage device as ultracapacitor and analyse its operating characteristics according to the power demand by running the model…

Q1) Load the vehicle parameters. Complete the vehicle model by modelling the remaining equations. Set simulation stop time to 598 sec. The output should be the vehicle velocity.   Vehicle Model in MATLAB SIMULINK:- Vehicle model here is nothing but the equation of forces which comes under velocity ie. when vehicle…

Create a Stateflow or Simulink model for the following flowchart. Load the .mat file into the workspace. The input to the model would be the power demand. The output should be: Fuel cell power Battery power FC Operating state (running, standby) Create plot of these outputs against time. (Note- The Simulink model file should…

Q1) Consider a scenario where an aggressive driver is accelerating very rapidly and braking harshly in a city driving. Is battery better a choice to supply power than UC in this scenario? True False Why? In the case of aggressive driving in the city, it is FALSE that a battery is a better choice to supply power…

Q1).Compare four different types of fuel cells and state their applications.   Fuel cell Operating temperature(°C) Power(kw) Efficiency(%) Application PEM(polymer electrolyte membrane) 60°C - 110°C 0.01-250 40%-55% portables,mobile,low power generation PAFC(phosphoric acid fuel cell) 70°C - 130°C…

Create a MATLAB model of electric car which uses a battery and a DC motor. Choose suitable blocks from Powertrain block set. Prepare a report about your model including following: Objectives:         1. System level configurations        2. Model parameters      …

    Which types of power converter circuits are employed in an electric and hybrid electric vehicle? There are four main categories of power converter circuits that are used in electric and hybrid electric vehicles. They are listed and elaborated below:- AC to DC Converter:- AC to DC converters is electrical…

In this project, a Simulink model for the DC motor will be first developed per the schematic shown in Figure 1. Use the Proportional, Integral, and Derivative (PID) control design knowledge gained in the training to design, develop and test a controller to maintain a desired speed for the motor.   Key Highlights:…