Project 1

AIM:- To develop general arrangement for the RC office building. Also, to analyze and design the building as per IS standard code in TEKLA STRUCTURAL DESIGNER from the attachment. Also, to generate report of each member and extract drawings for structural plans, beam reinforcement details from the software. INTRODUCTION:- Tekla…

1.) Based on the analysis design RC column and beam. AIM :    To Based on the analysis design RC column and beam.   INTRODUCTION :  An ordinary reinforced concrete beam or the column itself is an inhomogeneous section composed of concrete and reinforcement, whose behavior is totally different. A reinforced concrete column…

Ans 1:- AIM:- to generate the  report  for the steel  building design Procedure:- Open the Tekla model Now go to report option from the ribbon and select model report Now select the load cases and combinations summary to obtain report Click on the show report to obtain report We can change the project name , address etc…

1.Design the slab and foundation of the model. Outline the thought process for designing of the elements (column, beam, slab and foundations) Aim - To design the slab and foundation of the model. Tools Used - 1st Order analysis, Analysis all ( static ), Status , check panel ,Properties window etc.   Procedure - Open the…

1. Aim: To generate seismic loading based IS codal provisions and zone II. Procedure: Open the previously save Tekla model Now go to the load cases and add the seismic load case, and click ok Now go to the seismic wizard and select code specta and click Next. Now enter the zone and click Next Now we have to enter the structure…

1. Calculate dead load in design report based on IS code and apply dead load on the model Finishes of 50mm Slab thickness as per the design Brick wall load Roofing load   Aim - To calculate dead load in design based on IS Code and apply on model. Tools Used - Load Cases, Full Udl , Area Load, Property Window. Calculation…

1. Setup model for RC building design and based on following parameters for cover MEMBERS IN CONTACT WITH GROUND  ABOVE GROUND Column 50mm  40mm Beam 30mm  25mm Slab 30mm  25mm Pilecap 75mm   Foundation 50mm   AIM :    To Setup model for RC building design and based on following parameters for cover   INTRODUCTION :   …

Challenge 12 Submitted By Dineshkumar Commands Used in this challenge Line Rectangle Trim Move Copy Explode Circle Dimlinear Dimcontinue Boundary 3Dorbit 3D rotate Extrude Region UCS Camera Block Render RR Sweep Create Light   Create a 3D Isometric View of the building with plan and elevation given.     Aim: To draw the…

Analyze and design a steel building to 10T CRANE as per IS standard code using TEKLA STRUCTURAL DESIGNER.   AIM: To analyze and design a steel building to 10T CRANE as per IS standard code using TEKLA STRUCTURAL DESIGNER. INTRODUCTION: Tekla Structural Designer is an integrated model-based 3D tool for analysis and design…

To Analysis and Design of Steel Structures using TSD AIM: To Summarize the study for the bending moment, shear force and deflection diagrams for the elements of the model and Based on the analysis to design the members and to outline the thought process in selecting the member sizes along with the foundation design. INTRODUCTION:…

1.Aim: To generate manual wind loading in the design report based IS code as per the following input Basic wind speed = 39m/s Terrain category 2 Procedure: Open Excel sheet for calculation and open TSD file which created early to check dimension of the building. Refer code IS 875 Part-3 2015 for, For K1, For k2, K2 factor…

1.) Calculate dead load in design report based on IS code and apply dead load on the model Finishes of 50mm Slab as per design Brickwall 150mm thickness Roofing load based on purlin size Ceiling loading 0f 0.3KN per sq m  AIM :       To Calculate dead load in design report based on IS code and apply dead load on the model.…

1. AIm: To Create beam properties for the First floor and model the beams. Procedure: Open the Tekla structure software  And then open the week2 challenge file. Now go to levels and select intermediate floor Now go to manage property and create the new beam  And then model the beam. Now Model the secondary beams in the…

To model columns for industrial steel structure using TSD Introduction Tekla Structural Designer is an integrated model-based 3D tool for analysis and design (of both concrete and steel members) in multi-material structures. Features include interactive modeling, automated structural analysis and design, drawing, and report…

1) Aim - To summarize the user interface in TSD for the following items  Project Workspace - Open the Tekla structural designer software and click on New option and the new model workspace will appear Now all the ribbons and menu bars are visible Scene Content - Select window tab and then click on scene content…

1. In this project, participants will get to experience the entire design process from modelling, analysis, design, and preparation of construction     drawings. The architectural drawings of a G+3 RCC building is provided. The following information on the building is to be used: Location – Guwahati, Assam…

         Model the isolated footing provided in week 11 challenge on SAFE. Analyze and design it to verify the size, depth and steel provided as per calculations. Aim: To Analyze and design the isolated footing from week 11 challenge on SAFE and verify the size, depth and steel provided as…

DESIGN OF SHALLOW FOUNDATION (ISOLATED FOOTINGS)AIM: To design a square footing for a column size of 400x400 for the given data and to do following checks If the gross bearing pressure under the footing is within safe bearing capacity Provide sufficient depth and longitudinal steel for resisting bending and shear Sufficient…

STRUCTURAL MODELLING USING ETABS 2018   AIM: To model and analyze the G+7 residential building from the given architectural drawings using the ETABS 2018. To Run a modal response spectrum analysis and check analysis results of the Etabs model for inter-storey drift requirements, vertical & planar irregularities,…

Aim:      Detailing of shear wall Procedure: Step 1:      The provided ETABS model is analysed and the shear wall design is run as shown in the figure below. Step 2:     The mentioned shear wall is labelled as P1. The design results of pier P1 is extracted as shown below.  …

Answer: Aim:       To Providing details of longitudinal reinforcement for the two columns from foundation to terrace level. Step 1: 1) Open a G+4 Etab file 2) Click the Concrete Frame Design tool 3) Select the Display Design Info option 4) Choose design output as Longitudinal Reinforcement Step 2: 1) After…

      Reinforcement Detailing of Beams from ETABS output Detail design of beams in Etabs 2018.The ETABS file for a G+4 building is provided. Run the analysis and design the RCC Moment ResistingFrame. The following challenge deals specifically with two continuous beams in the 1st floor.      …

                                                                      Comparative Study of Different Story Buildings for Seismic Forces AIM:  …

1. The building shown, 20 x 30m in plan, has column on a 5 x 5m grid and shear walls( with dimensions shown in m, 250mm in thickness) in three alternative arrangements. (a, b, c), all with the same cross sectional area of the shear wall. Compare the three alternatives, taking into account the restraint of floor shrinkage,…

Model a 25 storey building on ETABS 2018 with structural properties as specified below. Ground floor or plinth floor level can be taken at a height of 1.5 metres from the base. Each of the successive 25 storeys has a storey height of 3 metres. Structural Element Sizes  Beams : 300 × 400 mm  Columns : 800 × 800 mm  Slab…

Question 1: Comment on the layout of the framing plan concerning earthquake resistance in the two horizontal directions X or Y (dots are columns, lines depict beams). Look into aspects of symmetry, redundancy and bi-directional stiffness and ductility.   Answer: 1.Symmertry Having a look over the aspects of symmetry…

  Q] A five storey structure with 5 translational DOF is shown here. Each storey has mass ‘m’. The eigenvalue problem has been solved and the 5 periods of vibration Tn and their corresponding mode shapes, φn has been derived. The fundamental period of vibration (T1 = 2 seconds) and its…

1. Differentiate Static analysis and Dynamic analysis with proper representing pictures (30 marks) AIM:-        To Differentiate Between Static analysis and Dynamic analysis Ans:-   Static Analysis:-  In Static analysis we analysis static load means “a force that has constant size,…

Identification of Cracks   1) What is the mode of failure or damage of the beams in the figure above? Would you characterize the case as damage or as a failure? Are the damages repairable? Elaborate. a)              This crack will be formed due to the flexural failure of a beam. The flexural strength, known as modulus…

1. Design a Warehouse Building located in Chennai using STAAD Pro Connect Edition. The specification must be as follows:      Width  30m Length 50m Eave Height 9m Bay spacing 6m Soil type Medium Safe Bearing Capacity 200 kN/m2 Roof slope 1 in 12 Assume suitable sections for structural elements.…

1. Design a multi-storey Residential Building located in Bangalore using STAAD Pro Connect Edition. The specification must be as follows:      Building floors G + 6 + R Plan dimension B = 25m ,  L = 16m Storey Height h = 3.5m Soil  Hard soil Use Residential Purpose Safe Bearing Capacity 180…

AIM:-        To explain the answer for each and every question from 1 to 3 INTRODUCTION:-         In this section of question from 1 to 3, I used staad.pro software to answer these question. Besides this, I have used some reference from recorded video session of skill-lync.…

AIM:-        To explain the answer for each and every question from 1 to 3  INTRODUCTION:-        In this section of question from 1 to 3, I used staad.pro software to answer these question.  I have used some reference from recorded video session of skill-lync. Question…

Q1. 1. Write the steps involved to upload a .std file through web mail?    2. Name the different materials that can be designed using STAAD Pro.    3. Is it possible to capture images in STAAD Pro? If yes how?    4. Name the three ways by which you can create a model.    5. Write the steps followed to assign properties…

Usage of Navigation tool , Timeliner and Clash Detection test                             using Naviswork 1) Use the Architecture/ Structure Project file developed by you in Week 6 to 8. Export the Revit architecture and structure model to Navisworks Cache file following the export settings discussed in class AIM:-    …

Creation of Sinusoidal curve and a Parametric stadium using                                         dynamo  1) Using Dynamo create a set of sinusodial points and create a curve and create a surface out of the curve.  AIM:-           To create a set of sinusodial points, create a curve and To create a surface out of the…

    Creating Architectural and Structural model with 3D                                    rendering using REVIT   1) Select the type of structure you want to build from one of the three below:       …

3D Creation of Celing, Roof, Architectural plan, Structural plan, Sectional view, Elevation view and Camera specific view for a house plan using REVIT   1. Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level.…

AIM:       To create a 3D rendered model for a Residential Building in AutoCAD INTRODUCTION:      The main objective of this project is to understand about to create a Plan in 2D, then convert it into 3D using AutoCAD 3D, applying materials and rendering.      AutoCAD…

1. Create a 3D Furniture element as shown in the Figure. Assume dimensions that are missing.                              AIM:            To create a 3D model of the Furniture element as per the given drawing …

1. Create a layout of the Plan and Section A of the project in Challenges 7, using the template Tutorial- mArch.dwt in a scale as given in the Figure. Use the MV command to create the viewport of the size as shown in Figure. Also, use the ATTEDIT command to edit the information in the title block. Use A1 size for the layout.…

1. Create the layouts of the Kitchen and provide hatches pattern as shown. Also, use blocks wherever required. Provide appropriate dimensions in the plan. Assume the size of doors, appliances and others as per the standards.     Aim:       To Create the Kitchen Layout and to Also, use…

AIM:    To Create Custom1_titleblock and Custom2_titleblock using Attributes and block command from Autocad software  Introduction:    The following commands and tools are used for this drawing.      * Line: It helps to create a line between two points      * Rectangle:…

SUMITED BY,                 DINESHKUMAR.M Design and Draft a layout of a residential building with the following details:                 a. Plot Size: 60’x20’(18.3m x6m)                 …

Sketch a G+1 floor residential plan, according to Vaastu Shastra, and list down the names of the structural rawings required to be provided to the site for construction. Also, assume the sizes of the structural elements (Column,Beam, Slab, etc.,) and accordingly calculate the individual corresponding loads…

  PROJECT ON CONCRETE MIX DESIGN OF M35 & M50 GRADES Design mix for M35 (with fly ash) & M50 grades.                                                           …