Drafting of various geometries using Chamfer, Fillet tool in AutoCad

Question 1:The building shown, 20 × 35 m in plan, has columns on a 5 × 5 m grid and shear walls (with dimensions shown in m, 250 mm in thickness) in three alternative arrangements, (a), (b), (c), all with the same total cross-sectional area of the shear walls. Compare the three alternatives, taking into account the restraint…

AIM:- To undersstand the  Concept on positioning of ColumnsINTRODUCTION:-There are some of the basic principles in determining the positions of columns. Some of them are:Columns should be preferred to be positioned at the corners of the building and at the intersection of beams.They should be placed in such a…

AIM:- Understanding the concepts on Degrees of FreedomINTRODUCTION:-A degree of freedom is the number of possible movements of a structural system. The degrees of freedom can be used to describe displacements and rotations at a nodal point. Thus, each degree of freedom allows for a displacement or a rotation in a…

Aim : To Answer given questions 1. Differentiate Static analysis and Dynamic analysis with proper representing pictures (30 marks)Static Analysis: Static analysis of structures considers static loads acting on the structure such as dead,live load which does not vary with time and are not considered to be…

1 a. Shear Crackb.Spalling of concrete due to insufficent of cover c.beam & column joint faliue due to improper and insufficent steel d. hinge faliure at beam joint e. Spalling of Concrete due to corrosion of steel f. improper concrete and steel reinforment at beam junctions, over loading of structure …

1. Design a Warehouse Building located in Chennai using STAAD Pro Connect Edition. The specification must be as follows:    Width 30mLength50mEave Height9mBay spacing6mSoil typeMediumSafe Bearing Capacity200 kN/m2Roof slope1 in 12Assume suitable sections for structural elements. Follow IS800:2007,…

answer is submitted through pdf sheets

Questions 1. 1. State the primary load cases to be considered for design.    2. What is One – Way slab?    3. What is the value of unit weight of structural steel and soil?    4. Name few sections that can be defined using Properties tab in STAAD Pro.    5. Define…

Q1] AIM:- 1. To assign Circular section to column 2. To assign Unit system to a .std model file 3. Parameters to be specified while using “Bay Frame” option 4. Name few codal standards incorporated in STAAD Pro software. 5. To specify the design compressive strength for a RCC section. PROCEDURE: - (1) Go to…

Q1. 1. Write the steps involved to upload a .std file through web mail? ANSWER:- Steps involved to upload a .std file through web mails are as follows; Open the STAAD pro software and locate the share option available on the introduction screen. After clicking on the share button, select send mail option. Then, browse…

1Q:Use the Architecture/ Structure Project file developed by you in Week 6 to 8. Export the Revit architecture and structure model to Navisworks Cache file following the export settings discussed in class PROCEDURE:Open revit sofware and select the week 8 challenge file. Now click on the FILE tab and select the Export…

1) Using Dynamo create a set of sinusoidal points and create a curve and create a surface out of the curve. A) AIM; To create a set of sinusoidal points and create a curve and create a surface out of the curve. Procedure: initailly open the revit software and go to the mangae tool in manage tab select the dynamo The…

  Creating Architectural and Structural model with 3D rendering using REVIT Introduction Revit enables the project to be completed in a combined effort. Structural engineers that are using Revit and are working with architects using Revit Architecture can directly link to the architectural model. Linking a revit architectural…

  Q1. Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level Aim: To Model a ceiling from the architecture tab above the walls at the first- Floor level of the residential unit project saved in week 3 Introduction:…

Open Autocadd    file 

Open Autocadd   Open New File   set units as per guideline   draw assignment as required 

Open Autocadd    Open New File    Set Units as per guidelines     draw as per assignment

Open Autocadd    Open New File    Set Units as per guideline   Draw assignment as per required 

Open Autocadd   Open New File    Set units as per guidelines    Draw as per assignment     

Open Autocadd     

Open Autocadd   Open New file  set units Draw as residential floor plan with 3d View  Render it 

submitted in dwg file 

Column Design Calculation 1. Load Calculation on Column we know that the Self–weight of Concrete is around 2400 kg/m3, which is equivalent to 240 kN and the Self–weight of Steel is around 8000 kg/m3. So, if we assume a column…

Design mix for M30 with fly ash  Design mix for M50 without fly ash