Challenge

Drafting of various geometries using Chamfer, Fillet tool in AutoCad

Aim : To draw the given drawing using Autocad Software.

Procedure for;

Drawing 1:

In the command prompt type UNITS and change length to decimals.
In command prompt type PL (Polyline) and draw line with the given dimensions and close the figure.
In command prompt type L (Line) and draw line vertical from midpoint of 3.00 length line.
In command prompt type CIRCLE and select the midpoint of the circle Type D for DIAMETER and draw the circle.
In command prompt type DIMLINEAR for linear dimensions.
In command prompt type DIMALINGNED for alingned lines.

Drawing 2:

In command prompt type UN (Units) to change the length type to Architectural.
In command prompt type L (Line) and draw the respective lines with given measurement.
Find out the angles by geometrical methods.
In command prompt type DIMSTY (Dimension style) and modify all the elements of the dimensions which are Symbols and arrows, Fit. Primary units.
In command prompt type DIMLIN (DIMLINEAR) to show the linear dimensions.
In command prompt type DIMALI (DIMALIGNED) to show the aligned dimensions.
In command prompt type DIMANG (DIMANGULAR) to show the angular dimensions.

Drawing 3:

In the command prompt type UNITS and change the length type to Engineering and change insertion to inches.
In command prompt type L (lines) and draw lines according to given measurements.
In command prompt type CIRCLE and draw of diameter 1'-6.0'' at the given point from base line.
In command prompt type DIMSTYLE to change the modify the dimension elements.
In command prompt type DIMLINEAR to show the linear dimensions.
In command prompt type DIMANGULAR to show the angular dimension.
In command prompt type DIMDIAMETER to shoe the dimension of the circle.

Drawing 4:

In command prompt type UNITS and change length type to decimal.
In command prompt type LINE and draw line as per given measurements.
In command prompt type DIMSTY (Dimension style) and modify all the elements of the dimensions which are Symbols and arrows, Fit. Primary units.
In command prompt type DIMLINEAR to show the linear dimensions.

Drawing 5:

In command prompt type UNITS to change the length in Decimals.
Turn on the Ortho by pressing F8 key.
In command prompt type LINE and draw line perpendicular at midpoint of 22.5 length line.
In command prompt type OFFSET and take it for middle line in both directions at 2.75 length.
Also OFFSET the small external lines of length 6.00 towards inward of the figure at 1.50 length.
In command prompt Type CIRCLE and draw circle at respective point.
In command prompt type ERASE to erase extra lines.
Use TEXT SINGLE LINE to type text.
In command prompt type DIMSTY (Dimension style) and modify all the elements of the dimensions which are Symbols and arrows, Fit. Primary units.
In command prompt type DIMLINEAR to show the linear dimensions.
In command prompt type DIMDIAMETER to shoe the dimension of the circle.

Drawing 6:

In command prompt type UNITS and change the length to decimals.
In command prompt type LINE and draw for length 2.00 (Horizotal) and 1.50 (Vertical).
In command prompt type OFFSET and take offset of 0.50 of both lines.
In command prompt type TRIM and trim the extra lines.
In command prompt type LINE and join the edges with line.
In command prompt type OFFSET and take the offset of lines of first horizontal line and any distance.
In command prompt type LINE and draw vertical line of top View.
With the help of OFFSET complete the figure.
TRIM the extra lines.

Drawing 7:

In command prompt type UNITS and change the length to decimal.
In command prompt type LINE and draw line of dimensions 100, 210, 75.
In command prompt type type OFFSET and take offset of lines according to rectangle dimensions.
In command prompt type TRIM to erase extra lines.
In command prompt type FILLET type the radius and select the cornes of respective lines.
In command prompt type ARC select start point and end point.
In command prompt type CIRCLE and select midpoint and type radius.
In command prompt type DIMSTY (Dimension style) and modify all the elements of the dimensions which are Symbols and arrows, Fit. Primary units.
In command prompt type DIMLINEAR to show the linear dimensions.
In command prompt type DIMDIAMETER to show the dimension of the circle.
In command prompt type DIMRADIUS to show the radius dimensions.

Drawing 8:

In command prompt type UNITS and change the units to decimal.
In command prompt type LINE and draw line of 8.550.
In command prompt Type CIRCLE and draw the circle of diameter 0.90. at both the end points as a center.
In command prompt type CIRCLE and draw the circle of radius 0.90 at both ends of line with same centre.
In command prompt type OSNAP and select TAngent mode and unselect the Centre mode.
In command prompt type LINE and draw the line at the tangent at both sides.
In command prompt type TRIM and trim the extra part of the circles and line of 8.55 units measurement.
In command prompt type DIMSTYLE and modift the dimensions settings.
In command prompt type DIMLINEAR and show the linear dimensions.
In command prompt type DIMRADIUS and show the radial dimensions.
In command prompt type DIMDIAMETER and show the diameter dimensions of the circles.

Drawing 9:

In command prompt type UNITS and change the length type to engineering.
In command prompt type LINE and draw the line of 32'6".
In command prompt type CIRCLE and draw the circle of 8' and 9' at both the ends of the line.
In command prompt type CIRCLE and select tan tan radius and select both tangent points and type radius of 41'8".
In command prompt type CIRCLE select tan tan radius and select both tangent points and type radius of 20'10".
In command prompt type TRIM and trim extra part of the circle and line.
In command prompt type DIMSTYE and modify the elements of the dimension Arrow, Scale, Primary units.
In command prompt type DIMLINEAR and show the linear dimension.
In command prompt type DIMRADIUS and show the radial dimension.

Drawing 10:

In command prompt type UNITS and change the length type to Engineering.
In command prompt type RECTANGLE and type both dimensions as same.
In command prompt type COPY and copy the drawn square object beside another object.
In command prompt type ROTATE and rotate one object at 45 deg.
In command prompt type MOVE and move the object towards centre of previous object acting as common centre.
In command prompt type OFFSET and offset both the squares.
In command prompt type TRIM and trim extra parts according object.

Drawing 11:

In command prompt type UNITS and change the length type to Architectural.
In command prompt type L (Line) and draw the lines of the specific measurement.
In command prompt type OFFSET and take the offset of lines and given distances.
USE TRIM command to erase extra lines.
In command prompt type RECT (Rectangle) to draw the square.
In command prompt type ROTATE and rotate the drawn square at an angle of 45 deg.
In command prompt type MOVE and move the square towards the centreline.
In command prompt type DIMSTY (Dimension style) and modify all the elements of the dimensions which are Symbols and arrows, Fit. Primary units.
In command prompt type DIMLIN (DIMLINEAR) to show the linear dimensions.
In command prompt type DIMANGULAR to show the angular dimension.
In command prompt type DIMDIAMETER to show the dimension of the circle.

Ship work like this
in your own course.