Creation of Multiple viewports, Scaling the drawing and setting in Template in AutoCad

    1. Design a Warehouse Building located in Chennai using STAAD Pro Connect Edition. The specification must be as follows: Width  30m Length 50m Eave Height 9m Bay spacing 6m Soil type Medium Safe Bearing Capacity 200 kN/m2 Roof slope 1 in 12 Assume suitable sections for structural elements. Follow IS800:2007,…

Aim  To design a multi-storey Residential Building located in Bangalore using STAAD Pro Connect Edition.  Procedure   DBR - Design Basis Report   Step 1) Given data  Building floors G + 6 + R Plan dimension B = 25m ,  L = 16m Storey Height h = 3.5m Soil  Hard soil Use Residential Purpose Safe Bearing Capacity 180 kN/m2…

1.1)How will you assign Circular section to column? Create the model in the staad pro that can be a column  Go to properties in that Define paramters  Assign the circular shape of the column  The radious of the circular is given   1.2)How will you assign Unit system to a .std model file? To Assignt…

1. 1. Write the steps involved to upload a .std file through web mail? Goto your mail Compose your mail To upload your file click attach Browse your file 1.2. Name the different materials that can be designed using STAAD Pro. The material that can be designed using STAAD Pro are Aluminum Concrete Steel Stainless Steel…

AIM: To Model, analyze, design, and prepare the construction drawings from the provided architectural drawing of a G+3 Hostel building. To design foundation detail illustrating the pile and pile cap reinforcement, Tie Beam details connecting the pile caps, Column reinforcement, Framing plan for the typical floor, Beam…

1.Aim Model the isolated footing provided in week 11 challenge on SAFE. Analyze and design it to verify the size, depth and steel provided as per calculations. Procedure go to safe software select New Model   Define Material Properties Like we did in ETABS, we need to define the material properties in an exact manner.…

AIM:- To model and analyze the G+7 residential building from the given architectural drawings using ETABS PROCEDURE:- STEP1:- First we have to open the ETABS software. Next click on the file option at the left side top corner and select the new model. After selcting the new model the new tab opens,in that tab we have to…

Aim: To run the analysis and design the RCC shear walls shown in the etabs model. Procedure: Open the Etabs file and run the analysis. After the analysis click shear wall design.                          Select display info and choose PM failure.                       Now select longitudnal reinforcement:go to concrete…

AIM:- To provide ,the details of longitudinal reinforcement for the two columns (3A & 3B), from foundation to terrace level. The details of shear reinforcement as per special confining reinforcement provision of clause 8.1 of IS 13920-2016. INTRODUCTION: A reinforced concrete column is a structural member designed to carry…

  AIM :  To Detail design of beams in Etabs  The ETABS file for a G+4 building is provided. Run the analysis and design the RCC Moment ResistingFrame. The following challenge deals specifically with two continuous beams in the 1st floor.  INTRODUCTION :  There are many softwares available for designing. But in this book ETABS…

AIM: TO MODEL AND ANALYZE MULTIPLE BUILDINGS WITH DIFFERENT FLOOR LEVELS AND DESIGN PARAMETERS USING ETABS SOFTWARE AND COMPARE THE RESULTS TO UNDERSTAND THEIR OVERALL SEISMIC BEHAVIOUR. INTRODUCTION:  The structural configuration of the building plays a major role in determining the overall response during an earthquake.…

Aim: To model and analyse a 25 storey building with given specifications and to cross check the parameters as per IS 1893 provisions. Procedure: • Open the ETABS software. • Click the file menu and choose to create a new model option. • After choosing a new model a dialogue box will appear as model intialization.…

Question 1: The building shown, 20 × 35 m in plan, has columns on a 5 × 5 m grid and shear walls (with dimensions shown in m, 250 mm in thickness) in three alternative arrangements, (a), (b), (c), all with the same total cross-sectional area of the shear walls. Compare the three alternatives, taking into account the restraint…

Question 1: Comment on the layout of the framing plan concerning earthquake resistance in the two horizontal directions X or Y (dots are columns, lines depict beams). Look into aspects of symmetry, redundancy and bi-directional stiffness and ductility.                    …

Question 1: A five storey structure with 5 translational DOF is shown here. Each storey has mass ‘m’. The eigenvalue problem has been solved and the 5 periods of vibration Tn and their corresponding mode shapes, φn has been derived. The fundamental period of vibration (T1 = 2 seconds) and…

 1)Compute lateral stiffness of the one story frame with an intermediate realistic stiffness of the beam. The system has 3 DOFs as shown. Assume L = 2h and Elb = Elc                                         …

a) Failure, with concrete crushing and bar buckling at the bottom flange next to the column Flexural damage, is mostly associated with cracking and spalling of concrete and yielding of the reinforcement. By contrast, flexural failure comes with the disintegration of concrete beyond the cover, often with buckling (or even…

1.Use the Architecture/Structure Project file developed by you in Week 6 to 8. Export the Courses Revit architecture and structure model to Navisworks Cache file following the export settings discussed in class. AIM: To export revit architectural model and structural model to "Navisworks". INTRODUCTION:- Navisworks project…

Creating Conceptual mass in REVIT and Creation of Sinusoidal curve and a Parametric stadium using Dynamo Introduction: Dynamo is an open source visual programming language for Revit, written by designers and construction professionals. Its a programminglanguage that allows you to type lines of code; while also creating…

1) Use the shortcut keys in Revit discussed in class to complete the following tasks and list them below           a. Using 3D model create a section box           b. To create similar doors and windows in a floor plan layout         …

1) What are HVAC systems? Why are they essential in the modeling of buildings HVAC Systems • HVAC systems are responsible for the regulation of heat, airflow, ventilation, and air conditioning of an entire building you won't see the machines when you enter the building but you will most certainly fool the effects…

1). Select the type of structure you want to build from one of the three below. a. Multi-Unit Residential Apartmentb. Office Buildingsc. School. From the above the options of type of structure to build a building, i need to pick a multi-unit residential Apartment. 2). Assume reasonable assumptions for geographic and…

1) Open an architectural template. Using the Manage tab set project base point and project shared coordinates for the project. Aim: to set project base point and project shared coordinates for the project. Procedure: To create project shared coordinates: Open architectural tab Open Manage tab. Click on project coordinates…

1) Why are building codes or standards essential for the modeling/ efficiency of drawings in Revit ? BUILDING CODES of standard modelling. A model building code organisation is a set of building codes that are developed and maintained by a standard organisation. This standard organisation operates indenpently of the jurisdiction…

1) Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level. AIM:- To model a Ceiling from the architecture tab above the walls at the first floor level. INTRODUCTION: The creation of Ceilings within Revit is a very similar…

1) Use the project file created from Week 2. Use it for this assignment. Based on your layout from week 2, using floor tool under architecture tab and select the floor with appropriate material and thickness using the property browser create a layout in the Ground floor Level. Align the floor plan with grids created from…

1) What is BIM? Summarize the features of BIM and benefits of using BIM over 2D CAD tools. A) Building Information Modeling (BIM): • BIM is an acronym for Building Information Modeling or Building Information Management. • It is a highly collaborative process that allows architects, engineers, real estate developers,…

1) From the file menu, create a new project (Structural / Architectural / Construction template ) and name the project appropriately AIM: To create the new project(structural/Architectural/Constructio n template)and name of the project appropriately. INTRODUCTION OF REVIT.: Revit architecture is designed to accommodate…

Aim:- To model the RC structure analyze and design the model elements as per the IS codal provisions procedure: Open a new template in tekla and then go to settings from the home tab Assign the design codes and units to be considered in the model Define the structural default settings Click on ok step 1:- To define the…

1. Aim: To generate report for the steel building design. Procedure: • Open the saved Tekla model • Now go to the report option from the Ribbon and select model report. • Now select the load cases and combinations summary to obtain report and Click on the Show report to obtain the report• We can change…

Aim To design the slab and foundation of Courses the model Procedure - Design of slab Open the previously saved file and open 3d view Click on 1st order analysis and run the analysis Also click on status view Select the slab and right click on it and click on check panel and it shows result If the error is occured,change…

Aim: To design the RC columns and beams after the analysis. Procedure: Open the saved Tekla file. Now right click the member to be designed, and then select interactive design and select static. Designing Columns Select Static from the Interactive Design, after that, a dialogue box appears. This dialogue box shows the…

AIM: To Generate seismic loading based IS codal provisions and zone II using seismic wizard. INTRODUCTION: Seismic load indicates how much seismic energy (waves of energy that travel through the earth) a structure would need to endure in a specific geographic location. In tekla software it is generated within the software…

1. Aim - To calculate dead load in design based on IS Code and apply on model. Calculation Slab Load = (Model Slab In Software) Finishes Loading (50 mm Thickness) = 0.05 x 24 kN/m^2 = 1.2 kN/m^2. (Area Loading). Brick wall with cement plaster thickness =225 mm Unit Weight = 20 kN/m^3. Floor Height (Ground Floor to First…

1.AIM Setup model for RC building design and based on following parameters for cover MEMBERS IN CONTACT WITH GROUND ABOVE GROUND Column 50mm 40mm Beam 30mm 25mm Slab 30mm 25mm Pilecap 75mm   Foundation 50mm PROCEDURE Open Tekla structural design Go to settings->Structure defaults Select the SSL for the cover in…

AIM: To Analyze and design a steel building to 10T CRANE as per IS standard code in TEKLA STRUCTURAL DESIGNER.Provide bracings and moment connection for lateral stability. INTRODUCTION: PROCEDURE: Open tekla software,under file click on new. from analysing the given plan,the column placement is decided. to go setting,check…

1. AIM: Summarize your study for the bending moment, shear force and deflection diagrams for the elements of the mode PROCEDURE: • Initally open the Tekla file you saved prviously Seismic data in the structure • To set->go to Load panel->Under seismic load go to Seismic wizard • Select the code spectra->Next…

1.Aim - Generate manual wind loading in the design report based IS code as per the following input Basic wind speed = 39 m/s Terrain category = 2 Procedure - First calculate load combination    Result - Calculations are done for the wall panel 2) Aim - Based on the above calculation apply the loading on the model…

1.Calculate dead load in design report based on IS code and apply dead load on the model Finishes of 50mm Slab as per design Brickwall 150mm thickness Roofing load based on purlin size Ceiling loading 0f 0.3KN per sq m  Aim: To Calculate dead load in design report based on IS code and apply dead load on the model…

  1.Creat beam properties for first floor and model the beams AIM: To create beam properties and model primary and secondary beams on the Ground floor, First floor, Roof levelINTRODUCTION: Tekla structure, basic building objects are provided and detailed further.Columns, Beams is modelled and properties…

1. AIM: Create column properties for different types of pedestal members and model in the grids created as per the assignment] SOLUTION • Open the Tekla Structural designer >project workspace will open • Create new file->Go to Model tab >Construction Level.• A new tab will open->create the levels…

1. Summarize the user interface in TSD with the for the following items: - Project Workspace - How to access and usage Scene Content - Demonstrate the use of scene content Create two scene views Loading drop list- How to access Properties windows - how to access and usage. Answer - Project Workspace - How to access and…

AIM: • To create a 3 dimensional model of the residential building• To create a rendered view of the developed model.• To use materials and light setting. Procedure: • Here in the project we are going to create a 3d model of a residential building.This is building after being created, it is rendered.•…

1)AIM:- To create a 3D isometric view of the given building with plan and elevation. INTRODUCTION:• An isometric drawing is a 3D representation of an object, room, building or design on a 2D surface.• One of the defining characteristics of an isometric drawing, compared to other types of 3D representation, is…

1 AIM: To create 3D model and view of:1. Furniture element2. Isolated footing3. AASTHO type girder4. Drop column with panel5. A wall Commands used: 1. Extrude.2. Offset.3. UCS.4. Box.5. Union.6. Subtract.7. Move.8. 3d orbit.9. Loft.10. Sweep.11. Cone.12. Region.13. Boundary. INTRODUCTION BY 3D VIEW • The process of…

AIM: 1. To create layout of plan and section, creating viewports, editing attributes and taking a plot.2. To create a kitchen layout in A4 sheet and take a plot3. To create Multiview ports for industrial section drawing, scaling it and taking a plot. COMMANDS USED: 1. View2. Layout.3. Multiple View.4. Model Space.5. Paper…

Aim: To Create the Kitchen Layout and to Also, use proper dimension techniques to dimension the kitchen layout. Also, insert text wherever required. All dimensions are in mm.Procedure: step 1: • units are set to mm• limits and limax are also set• zoom comand is also used Steps for drawing Below Counter Plan…

Aim: To create: Courses 1. Template, inserting text and attributes 2. Doors of warehouse and placing it in blocks 3. Electrical legend and making it blocks 4. Different types of door for residential project 5. Drawing bars, making it as block and making it as a table as bar bending schedule. Commands used: 1. Block. 2.…

Aim: To draw 1. Architectural drawing of a residential building: Plan of a residential building. Elevation of a residential building. Section of a residential building. 2. Structural drawing: Column plan layout of the building. Footing plan layout of the building. Beam plan layout of the building. Commands used; Line,…

Aim: To draw the floor plans and sections using the proper dimension techniques and dimension styles to document the project. Introduction: • Plan and Sections are different types of drawings used by architects to graphically represent a building design and construction. • A plan drawing is a drawing on a horizontal plane…

  1AIM: T Draw the elevation and details of a wardrobe  STEP 1: • Units are set to mm • Limits and limax are also set • Zoom command is also used STEP 2: • In the command line type rec > 2800,2600 • In the command line type offset • Offset from the top of the dimensions 12mm and…

1.Aim To creatin the column schedule as show in figure Procedure In the command promt tyle line to creat tables In the command prompt type st (text style) roman.shx (font name)>8"(height)>left(justify) In the command promt type text to text the given text in the drawing In the command prompt type MTEXT (multiline…

Aim Drafting of various geometries using Chamfer, Fillet tool in AutoCad Command useLineCircleChamferFilletMirror TrimMoveRotate Annotate Procedure 1. Decimal 1.new sheet unit decimal precision 0.00 meter ok2.limit o,o and 420,2103zoom all4sekect the line tool and draw the length starting from base 3 unit Give line command…

Aim Creating a floor plan,footing detail and isometric view using Autocad To Creating a floor planCommand use 1.Line2.Rectangle 3.Offset4.Trim Procedure 1.Select Rectangle by Rectangle in command box 2.Specify the boundaries point that you need 3.after that take line in ribbon dilogue box and draw inner wall 4 Select offset…

AIM       Create the geometries from P1 to P2 using all the coordinates system methods. You need to use the Line tool to create the geometries. Where required you need to use the circle tool.

Sketch a G+1 floor residential plan, according to Vaastu Shastra, and list down the names of the structural drawings required to be provided to the site for construction. Also, assume the sizes of the structural elements (Column, Beam, Slab, etc.,) and accordingly calculate the individual corresponding loads from the members…

Mix Design for M35 grade concrete with fly asConcrete This section has Specifications of the materials and requirements of the concrete to be made • Grade Designation = M35• Type of Cement = OPC 53• Type of Admixturev= Fly ash• Maximum NominalSize ofAggregate = 20mm• Minimum Cement Content =340kg…