AIM: To Create a the geometries from P1 to P2 using all the coordinates system methods.
INTRODUCTION:
• In this Challenge we create a basic drawings that followed by given dimensions using all coordinates system and the help of Line and Circle Command.
• Use the Imperial Template and the Decimal Units to draft the features.
PROCEDURE :
There are few methods
FOR P1 -
Consider any point and through that point
Using line command draw 6" line in Y direction and draw 6" line in X direction
Drag and press 6 then press enter
From vertical lines top point draw a 6" horizontal line on right hand side
You get C shape in single line
Then from the top lines right end point draw a 1" line downwards
Again continue that line towards left hand side upto 5" then down side 4"
Again continue that line towards right hand side upto 5" then down side 1"
Now you get C chape in double line
Give the dimension using Dimension command
Use QLEADER command for giving axis cordinate(2,1)
FOR P2 -
Consider any point and through that point
Using line command draw 7" line in Y direction and draw 7" line in X direction
From vertical lines top point draw a 7" horizontal line on right hand side
Attatch all the points
you get a rectangle from top left corner draw a line 2" line towards right hand side and with the help of that ending point joined the end point at bottom left corner of the rectangle simmilarly from top right corner draw 2" towards left hand side and with the help of that ending point joined the end point at bottom right corner of the rectangle
delete extra part of the rectangle
you get a trapezoidal shape
for bottom part draw straight line at 3" and then extend vertically upward upto 4"
then towards right hand side and extend vertically downward delete extra 1" at bottom part
then gives dimension using dimension command
Use QLEADER command for giving axis cordinate(2,1)
FOR P3 -
Create M using line and dimention command
draw 5" x 7" rectangle
longer side consider vertically
so taking 1" line from bottom part towards right hand side simmilarly 1" line from bottom part towards left hand side
extend both the ends upward upto 4"
from bottom line center part extend line upto 2"
bothe open ends join at the middle point you get single line M
from upper line center part extend line upto 3"
join the upper corners at the middele
delete extra lines and you get double line M shape
then gives dimension using dimension command
Use QLEADER command for giving axis cordinate(2,1)
FOR P4 -
Make a rectangle 7" x 8"
takes longer side vertically
with 2" opening at bottom side complete double line U shape with 1" width
join the remaining part with the same width
delete extra lines and you get double line structure
then gives dimension using dimension command
Use QLEADER command for giving axis cordinate(2,1)
FOR P5 -
Make a rectangle 6" x 8"
takes longer side horzontally
draw 2 rectangle inside the larger rectangle as per dimention 1" x 2"
1" gap between both the rectangle
rectangle are 1" from right side and bottom side
delete extra lines and you get double line structure
then gives dimension using dimension command
Use QLEADER command for giving axis cordinate(2,1)
FOR P6 -
Make a I shape drawing
It can be draw with three rectagulars
upper with dimension 8" x 2"
consider longer side horizontally
middle with dimension 2" x 4"
consider longer side vertically
bottom with dimension 10" x 2"
consider longer side horizontally
delete extra lines and you get double line structure
then gives dimension using dimension command
Use QLEADER command for giving axis cordinate(0,0)
FOR P7 -
Make a rectangle 5" x 7"
longer side consider vertically
extend vertical line from right hand bottom corner upto 2"
then drag towards left hand side straight upto 3"
drag down upto 1"
again drag towards left hand side straight upto 1"
extend vertically upto 2"
drag horizontally towards right upto 3"
again vertically 1"
finally join that point to upper left corner
delete extra lines and you get double line structure
then gives dimension using dimension command
Use QLEADER command for giving axis cordinate(1,1)
FOR P8 -
Make a P shape
draw a rectangle with dimention 7" x 5"
consider long side vertically
starting from upper right corner
drag the line from that point downward upto 4"
again drag towards left upto 3"
again drag towards down 3"
then join with bottom left corner
make a rectangle in that structure with dimension 3" x 2"
from every side make a gap with 1"
delete extra lines and you get double line structure
then gives dimension using dimension command
Use QLEADER command for giving axis cordinate(1,1)
FOR Profile Wood -
draw a line 2"
then from right end drag down upto 5"
again drag towards left upto 2"
then downside upto 1"
drag towards right hand upto 10"
continue that line upward upto 1"
again towards left upto 2"
continue vertically upto 4"
drag right upto 2"
again drag upward 1"
drag a line set dimension and press shift plus less than symbol and enter angle 121
simmilarly from the starting point drag a line set dimension and press shift plus less than symbol and enter angle 31
you get a cross delete extended lines
take a measurement downward 5" from the 118 angle point
When you get that point by using circle command make a circle of 4 diameter
indicate the diameter dimension
delete extra lines and you get double line structure
then gives dimension using dimension command
and use the angular dimension command for angles
Use QLEADER command for giving axis cordinate(0,0)
FOR QUEEN POST TRUSS -
Draw a aline using line command drag towards right upto 7"
make a 45 degree angle using that line
you get a triangle divide that triangle into two parts by line command
from base left corner towards right drag 1 line upto 1"
its conect with left side of triangle
siimilar process at left
from base right corner towards lrft drag 1 line upto 1"
its conect with right side of triangle
both end which you have get connect at the center of base line
at both base corner drag line downwards uptp 4"
delete extra lines and you get double line structure
then gives dimension using dimension command
and use the angular dimension command for angles
Use QLEADER command for giving axis cordinate(1,1)
FOR MONO PITCH -
Make a righ angled triangle with dimension base line 6"
height 2"
divide that base line in 3 parts
make a line between connecting diagonal point and base lines adjusant point
delete extra lines and you get double line structure
then gives dimension using dimension command
and use the angular dimension command for angles
Use QLEADER command for giving axis cordinate(1,1)
RESULT: At Finally we learn the Gemontry coordinate system with simple drawings.
Post Graduate Program in Hybrid Electric Vehicle Design and Analysis
