Menu

Executive Programs

Workshops

Projects

Blogs

Careers

Student Reviews



More

Academic Training

Informative Articles

Find Jobs

We are Hiring!


All Courses

Choose a category

Loading...

All Courses

All Courses

logo

Creating Conceptual mass in REVIT and Creation of Sinusoidal curve and a Parametric stadium using Dynamo

1) Using Dynamo create a set of sinusoidal points and create a curve and create a surface out of the curve. AIM: Need to create sinusoidal point then curve from the point and then create surface INTRODUCTION: By using dynamo created a sinusoidal point then created a curve from the point and converted into the surface PROCEDURE:…

Project Details

Loading...

Leave a comment

Thanks for choosing to leave a comment. Please keep in mind that all the comments are moderated as per our comment policy, and your email will not be published for privacy reasons. Please leave a personal & meaningful conversation.

Please  login to add a comment

Other comments...

No comments yet!
Be the first to add a comment

Read more Projects by MD Majid (16)

Project 2

Objective:

1) Design a Warehouse Building located in Chennai using STAAD Pro Connect Edition. The specification must be as follows:      Width  30m Length 50m Eave Height 9m Bay spacing 6m Soil type Medium Safe Bearing Capacity 200 kN/m2 Roof slope 1 in 12 Assume suitable sections for structural elements. Follow IS800:2007, IS1893…

calendar

06 Jul 2023 04:03 AM IST

    Read more

    Project 1

    Objective:

    Ans)  1. Design a multi-storey Residential Building located in Bangalore using STAAD Pro Connect Edition. The specification must be as follows:      Building floors G + 6 + R Plan dimension B = 25m ,  L = 16m Storey Height h = 3.5m Soil  Hard soil Use Residential Purpose Safe Bearing…

    calendar

    06 Jul 2023 04:02 AM IST

      Read more

      Week 3 Challenge

      Objective:

      1. 1. State the primary load cases to be considered for design.    2. What is One – Way slab?    3. What is the value of unit weight of structural steel and soil?    4. Name few sections that can be defined using Properties tab in STAAD Pro.    5. Define Primary Beams. 2. 1. State the factors and parameters that influence…

      calendar

      24 Jun 2023 10:16 AM IST

      • Buildings
      Read more

      Week 2 Challenge

      Objective:

      Que :- 1. 1. How will you assign Circular section to column? Ans :-  Go to properties in that select define property select circle and give the radius for the member and assign the defined circle to the member created     Que :- 1. 2. How will you assign Unit system to a .std model file?  Ans :-  While creating a model…

      calendar

      23 Jun 2023 09:27 AM IST

        Read more

        Week 1 Challenge

        Objective:

        Q1. 1. Write the steps involved to upload a .std file through web mail? ANSWER:- Steps involved to upload a .std file through web mails are as follows; Open the STAAD pro software and locate the share option available on the introduction screen. After clicking on the share button, select send mail option. Then, browse…

        calendar

        22 Jun 2023 03:35 AM IST

          Read more

          Usage of Navigation tool , Timeliner and Clash Detection test using Naviswork

          Objective:

          1) Use the Architecture/ Structure Project file developed by you in Week 6 to 8. Export the Revit architecture and structure model to Navisworks Cache file following the export settings discussed in class AIM: To use the architecture/ structure project file  to export revit architecture and structural model to Naviswork…

          calendar

          16 Jun 2023 01:59 PM IST

            Read more

            Creating Conceptual mass in REVIT and Creation of Sinusoidal curve and a Parametric stadium using Dynamo

            Objective:

            1) Using Dynamo create a set of sinusoidal points and create a curve and create a surface out of the curve. AIM: Need to create sinusoidal point then curve from the point and then create surface INTRODUCTION: By using dynamo created a sinusoidal point then created a curve from the point and converted into the surface PROCEDURE:…

            calendar

            15 Jun 2023 07:01 AM IST

            Read more

            Creating Architectural and Structural model with 3D rendering using REVIT

            Objective:

               1) Select the type of structure you want to build from one of the three below        a. Multi Unit Residential Apartment        b. Office Buildings        c. School Ans:- As per the given options in the question I am opting for Multi Unit Residential Apartment 2) Assume reasonable assumptions for geographic and location…

            calendar

            11 Jun 2023 05:05 AM IST

            Read more

            3D Creation of Ceiling, Roof, Architectural plan, Structural plan, Sectional view, Elevation view and Camera specific view for a house plan using REVIT

            Objective:

            ans1) AIM: Created a ceiling in the first floor level  INTRODUCTION: From the architectural tab to model a ceiling at the first floor level on the saved week 3 project of the residential unit. PROCEDURE: STEP 1) OPEN MODEL Launch the Revit software Click on open and select previously created drawing as Arch_Drawing_chanllenge2…

            calendar

            03 Jun 2023 05:22 AM IST

              Read more

              Project 2_Creating a 3D rendered model for a Residential Building in AutoCad

              Objective:

              ANS1)   

              calendar

              27 May 2023 08:34 AM IST

                Read more

                Creating 3D Isometric view of various structural elements in AutoCAD

                Objective:

                ANS1)       ANS2)   ANS3)   ANS4)    

                calendar

                27 May 2023 08:30 AM IST

                  Read more

                  Creating various 3D Models like Furniture, Footing, Girder, Column drop with panel and Gable Wall in AutoCad

                  Objective:

                  ANS1)        ANS2)              ANS3)         ANS4) ANS5)                       

                  calendar

                  27 May 2023 08:21 AM IST

                    Read more

                    Creation of Multiple viewports, Scaling the drawing and setting in Template in AutoCad

                    Objective:

                    ANS1)                ANS2)    ANS3)                  

                    calendar

                    27 May 2023 08:14 AM IST

                      Read more

                      Creating Kitchen layout, Hatching of Architectural elements and sectional view of an Industrial Building in AutoCad

                      Objective:

                      ANS1)   ANS2)               ANS3)  

                      calendar

                      26 May 2023 05:12 AM IST

                        Read more

                        Creating Bar Bending schedule, Different Door types, and Creation of standard drawing templates using AutoCad

                        Objective:

                        ANS1)    ANS2)   ANS3) ANS4)  ANS5)      

                        calendar

                        26 May 2023 05:09 AM IST

                          Read more

                          Project 1 _Creating an Architectural plan for the provided plot size and develop relevant basic structural drawings

                          Objective:

                          ANS1)            ANS2)              COLUMN AND FOOTING)        

                          calendar

                          26 May 2023 04:59 AM IST

                            Read more
                            Showing 1 of 16 projects