Creating Bar Bending schedule, Different Door types, and Creation of standard drawing templates using AutoCad

Question 01. Design a Warehouse Building located in Chennai using STAAD Pro Connect Edition. The specification must be as follows ?      Width  30m Length 50m Eave Height 9m Bay spacing 6m Soil type Medium Safe Bearing Capacity 200 kN/m2 Roof slope 1 in 12 Assume suitable sections for structural elements. Follow IS800:2007,…

                                                                               PROJECT NUMBER :- 01                                                                       SUBMITED BY :- ABHISHEK VERMA 01. Design a multi-storey Residential Building located in Bangalore using STAAD Pro Connect Edition.      The specification…

                                                                  *        PROJECT NO :- 02      * 01.  In this project, participants will get to experience the entire design process from modelling, analysis, design, and preparation of construction drawings. The architectural drawings of a G+3 RCC building is provided.…

                                    Foundation Design using SAFE Question 01). Model the isolated footing provided in week 11 challenge on SAFE. Analyze and design it to verify the size, depth and steel provided as per calculations.…

                                    *   DESIGN OF SHALLOW FOUNDATION ISOLATED FOOTING     * Aim :- To design a square footing for a column of size 400x400 using some of the informations such as  The compression…

                   *  STRUCTURAL MODELLING OF RESIDENTIAL BUILDING USING E-TABS 2018   * QUESTION :- The architectural drawings for a G+7 residential building in zone 5 has been provided. The floor plan is the same for all 7 floor levels. Possible column positions have also been provided. Conceptualize a framing plan layout…

Question 01 part :- Part 01. State the primary load cases to be considered for design ? ANSWER :- The primary load cases that are to be considered for design are listed below :- Dead Load (IS 875 : Part I). Live Load (IS 875 : Part II). Wind Load (IS 875 : Part III). Snow Load (IS 875 : Part IV). Seismic Load…

Question :- The E-Tabs file for a G+6 building is provided. Run the analysis and design the RCC shear walls (show in the etabs model). The following challenge deals specifically with the shear wall of size 300x1500 at grid A-11 in the structural model. Extract values of longitudinal steel ratio, boundary element length…

Reinforcement detailing of columns in Etabs 2018.Question :- The ETABS file for a G+4 building is provided. Run the analysis and design the RCC Moment Resisting Frame. The following challenge deals specifically with two columns at the following grid intersections.3A3BProvide details of longitudinal reinforcement for the…

Question 1. 1. How will you assign Circular section to column ?    2. How will you assign Unit system to a .std model file ?    3. What are the parameters to be specified while using “Bay Frame” option ?    4. Name few codal standards incorporated in STAAD Pro software ?    5. How will you specify the design compressive…

Question 01 :- Part 01. Write the steps involved to upload a .std file through web mail ? ANSWER :- Steps involved to upload a .std file through web mails are as follows :- Open the STAAD pro software and locate the share option available on the introduction screen. After clicking on the share button, select send mail…

                    *   Challenge 7 – Detailed design of concrete buildings - 01     * Question :- Detail design of beams in Etabs 2018. The ETABS file for a G+4 building is provided. Run the analysis and design the RCC Moment ResistingFrame. The following challenge deals specifically with two continuous beams in the 1st…

                                                                                 *    PROJECT     *                                           Comparative Study of Different Story Buildings for Seismic Forces AIM :- TO MODEL AND ANALYZE MULTIPLE BUILDINGS WITH DIFFERENT FLOOR LEVELS AND DESIGN PARAMETERS USING ETABS SOFTWARE…

Challenge 6 – ETABS modelling of a 25 storey building Question :- Model a 25 storey building on ETABS with structural properties as specified below. Ground floor or plinth floor level can be taken at a height of 1.5 metres from the base. Each of the successive 25 storeys has a storey height of 3 metres. Structural Element…

Question 01) Use the Architecture/ Structure Project file developed by you in Week 6 to 8. Export the Revit architecture and structure model to Navisworks Cache file following the export settings discussed in class ? Answer :- AIM :- To use the architecture/structural project file developed from week 6-8, Export the Revit…

* Creating Conceptual mass in REVIT and Creation of Sinusoidal curve and a Parametric stadium using Dynamo * Introduction :- Dynamo is an open source visual programming language for Revit, written by designers and construction professionals. Its a programminglanguage that allows you to type lines of code : while also creating…

Question 01 :- The building shown, 20 × 35 m in plan, has columns on a 5 × 5 m grid and shear walls (with dimensions shown in m, 250 mm in thickness) in three alternative arrangements, (a), (b), (c), all with the same total cross-sectional area of the shear walls. Compare the three alternatives, taking into account the…

Question 01: Comment on the layout of the framing plan concerning earthquake resistance in the two horizontal directions X or Y (dots are columns, lines depict beams). Look into aspects of symmetry, redundancy and bi-directional stiffness and ductility ?                  Answer :- 1. Symmertry :- Having a look over the…

Question 01 :- A five storey structure with 5 translational DOF is shown here. Each storey has mass ‘m’. The eigenvalue problem has been solved and the 5 periods of vibration Tn and their corresponding mode shapes, φn has been derived ? Answer :-                       Answer :-  Aim :- To compute the values of seismic…

Question 01. Differentiate Static analysis and Dynamic analysis with proper representing pictures ? Answer :-                                   *  STATIC ANALYSIS  *                         *  DYNAMIC ANALYSIS  * 1. Load is not variable with time and neglected due to slow applying of load. 1. Load is variable with time…

Question 01. ) What is the mode of failure or damage of the beams in the figure above ? Would you characterize the case as damage or as a failure ? Are the damages repairable? Elaborate.    Amswer :- This crack will be formed due to the flexural failure of a beam. The flexural strength, known as modulus of rupture, bend…

Question 1). Select the type of structure you want to build from one of the three below:        a. Multi-Unit Residential Apartment        b. Office Buildings        c. School. ANSWER :- From the above the options of type of structure to build a building, i need to pick a multi-unit residential Apartment.    Question 2).…

Question 01. ) Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level. Answer :-      AIM :- 4 To model a Ceiling from the architecture tab above the walls at the first-floor level.     INTRODUCTION :- The creation of…

AIM :-  To create a 3D rendered model for a Residential Building in AutoCAD INTRODUCTION :- The main objective of this project is to understand about to create a Plan in 2D, then convert it into 3D using AutoCAD 3D, applying materials and rendering. AutoCAD is primarily used for generating 2D sketches. While it is possible…

Submitted By Abhishek Verma Commands Used in this challenge Line Rectangle Trim Move Copy Explode Circle Dimlinear Dimcontinue Boundary 3Dorbit 3D rotate Extrude Region UCS Camera Block Render RR Sweep Create Light   Question 01. Create a 3D Isometric View of the building with plan and elevation given.     Aim :- To draw…

AIM :- To create 3D model and view of Furniture element Isolated footing AASTHO type girder Drop column with panel A wall Commands used :- Extrude. Offset. UCS. Box. Union. Subtract. Move. 3d orbit. Loft. Sweep. Cone. Region. Boundary. PROCEDURE :-  Open the AutoCAD, click on workspace switching and change it…

AIM'S :- To create layout of plan and section, creating viewports, editing attributes and taking a plot. To create a kitchen layout in A4 sheet and take a plot To create Multiview ports for industrial section drawing, scaling it and taking a plot. COMMANDS USED :- View Layout. Multiple View. Model Space. Paper Space. Scale.…

Question 01. Create the layouts of the Kitchen and provide hatches pattern as shown. Also, use blocks wherever required. Provide appropriate dimensions in the plan. Assume the size of doors, appliances and others as per the standards.                    Aim :-  To Create the Kitchen Layout and to Also, use proper dimension…

Aim's :- To create :- Template, inserting text and attributes Doors of warehouse and placing it in blocks Electrical legend and making it blocks Different types of door for residential project Drawing bars, making it as block and making it as a table as bar bending schedule.   Commands used:  Block. Insert. Attributes.…

Project 1 (AutoCAD) Submitted by Abhishek Verma Commands Used in this challenge Line Xline Polyline Rectangle Circle Arc Trim Move Offset Hatch Layer MatchProp Multileader Fillet Copy Explode Dimlinear Dimcontinue Dim break Dim update Hide pallets (POFF) Show pallets (PON) Question's . Design and Draft a layout of a residential…

Aim of the Project :- To sketch a G+1 floor residential plan according to vastu Shastra and to list down the names of structural drawings required to be provided to the site for construction. To assume the size of structural elements (Column, Beam, slab etc) and to calculate the loads from the members as per IS code. Ground…

                *  Calculate the Concrete Mix Design for M35 grade concrete with fly ash   *   Aim : Mix design for M 35 grade concrete with fly ash   Step 01 : Stipulation's for proportioning     A  - Grade designation  M35  …