Creating a Residence Layout, Seating plan, Toilet and Utility room plan using AutoCad

1. AIM:- To draw a residence plan of figure 1 with the use of AutoCAD 2022

PROCEDURE:-Click on AutoCAD application and open the application . Type a command QNEW to save the file .Type a command units. .Select architectural type,0'-0 1/2" in precision,insertion scale units in inches,decimal type and precision in 0 for decimal.Click OK

• Type a command limmaxEnter new value for limmax:- 100',100' .Type a command zoom and select all .Type a command limits .Specify lower left corner:- 0,0

 Specify upper right corner:- 70',70' . Type a command zoom and then select all .Type a command XLINE .Specify the line:- Vertical .Specify through point:- Click it anywhere. .Type a command XLINE .

Specify the line:- Horizontal .Specify through point:- Click it anywhere .Type a command and then trim at corner edge .Type a command:-Offset

.Specify offset distance:- 9" Type a command:- Offset .Specify offset distance:- 43'6.5"

.Type a command offset

 .Specify offset distance:- 9"

.Type a command offset

.Specify offset distance:- 25'

.Type a command trim and then trim the unwanted lines .To draw a bed 1, type a command offset . Specify offset distance:- 11'7.5"  .To draw an inner wall, type a command offset .Specify offset distance:- 4.5" .Type a command offset .Specify offset distance:-12' .Type a command trim and then trim the unwanted lines .To draw a bed 2,type a command offset .Specify offset distance:- 11'6" .Type a command trim and trim the unwanted lines .To draw a toilet 1, type a command offset .Specify offset distance:-4.5" for interior wall .Type a command offset .Specify offset distance:-4'6" .Type a command offset .Specify offset distance:-4.5" for interior wall .Type a command offset .Specify offset distance:-8'3" .Type a command offset .Specify offset distance:-4.5" .Type a command trim .Trimmed the unwanted lines .To draw a toilet 2, type a command offset .Specify offset distance:-8'1.5" .Type a command offset .Specify offset distance:-4.5" .Type a command trim .Trim the unwanted lines 

.To draw a kitchen, type a command offset .Specify offset distance:-2' .Type a command offset .Specify offset distance:-6'8" .Type a command offset .Specify offset distance:-11'7.5" .Type a command offset .Specify offset distance:-9" .Type a command offset .Specify offset distance:-6'4" .Type a command trim .Trimmed the unwanted lines .To draw a living room, type a command offset .Specify offset distance:-11' .Type a command offset .Specify offset distance:-9" .Type a command trim .Trimmed the unwanted lines .To draw a door section, type a command circle,offset and extend . To draw a staircase, Specify offset distance for 1' for each step ( 9 steps) .Select the mid point of the line and draw an inclined line at the end point of it .Type a command D or dimension style manager .Select text height of 2 1/2",Precision of 0'-0" and overall scale factor of 5 units

.Type a command mtext

.Specify text height of 10"

.Dimensions of the above geometry is done with the use of command Dimension Linear .Type a command layer properties to group down geometry is done in distinct and seperate categories

RESULT:- The above residence plan is done with the use of commands such as Xline,offset,Circle etc on AutoCAD 2022

2. AIM:- Sketch the seating plan for an outdoor canopy of figure 2 with the use of AutoCAD 2022

PROCEDURE:- Click on AutoCAD application and open the application .Type a command QNEW to save the file .Type a command units.Select decimal type,0 in precision,insertion scale units in millimetres,decimal type and precision in 0 for decimal.Click OK

. .limits command is used .limmax command is also used .Zoom command is also used .Type a command circle .Specify centre point of circle:-0,0 .Specify radius of circle:-452 .Type a command circle .Specify centre point of circle:-0,0 .Specify radius of circle:-1398

Type a command line .Enter a line passing through the centre of the circle .Type a command offset . Specify offset distance:- 645 from the centre of the circle vertically .Type a command offset .Specify offset distance:- 225  from @-645,0 horizontally on both the sides .Type a command rectangle .Specify corner point:-@-645,0 .Specify length and width of the rectangle:-190,450 .Type a command fillet .Select radius .Specify fillet radius:-10 .Type a command fillet .Specify fillet radius:-10 .Draw a semeicircle of radius 225 mm .Type a command offset .Specify offset distance:- 25 from @-1060,0 .Type a command offset .Specify offset distance:- 75 from @ -1085,0 .Draw the end points of the line .Type a command offset .Specify offset distance:- 25 from @-835,0 .Type a command rectangle .Specify length and width of the rectangle:-90,74 .Type a command trim .Trimmed the unwanted lines .Copying the selected object and move at remaining three corner of the sides of the circle .Type a command rotate .Rotate angle by 45 degree on remaining three corners

Type a command D or dimension style manager

.Select text height of 2.5,Precision of 0 and overall scale factor of 25 units

Dimensions of the above geometry is done with the use of command Dim Radius

RESULT:- The above seating plan is done with the use of commands such as 0ffset,Circle etc on AutoCAD 2022

3. AIM:- Sketch the plan for toilet and utilities room of figure 3 with the use of AutoCAD 2022

PROCEDURE:-Click on AutoCAD application and open the application .Type a command QNEW to save the file .Type a command units.Select decimal type,0 in precision,insertion scale units in millimetres,decimal type and precision in 0 for decimal.Click OK

limits command is used .limmax command is also used .Zoom command is also used .Type a command XLINE .Specify the line:- Vertical .Specify through point:- Click it anywhere .Type a command XLINE .Specify the line:- Horizontal .Specify through point:- Click it anywhere .Type a command offset .Specify offset distance:-150 .Type a command offset .Specify offset distance:-300 .Type a command offset .Specify offset distance:-1900 .Type a command offset .Specify offset distance:-150 .Type a command offset .Specify offset distance:-2100 .Type a command offset .Specify offset distance:-150 .Type a command offset .Specify offset distance:-1700 .Type a command offset .Specify offset distance:-300 .Type a command trim .Trimmed the unwanted lines .Type a command offset .Specify offset distance:-150 .Type a command trim .Trimmed the unwanted lines .Type a command offset .Specify offset distance:-150 .Type a command trim .Trimmed the unwanted lines . Type a command offset .Specify offset distance:-631 .Type a command offset .Specify offset distance:-25 .Type a command offset .Specify offset distance:-50 .Type a command offset .Specify offset distance:-702 .Joined the vertical line .Type a command offset .Specify offset distance:-150 .Type a command offset .Specify offset distance:-402 .Type a command offset .Specify offset distance:-150 .Type a command offset .Specify offset distance:-150 .Type a command trim .Trimmed the unwanted lines .Type a command offset .Specify offset distance:-201 .Type a command offset .Specify offset distance:-351 .Type a command offset .Specify offset distance:-150 .Type a command offset .Specify offset distance:-402 .Type a command offset .Specify offset distance:-150 .Type a command trim .Trimmed the unwanted lines .To draw a window, type a command window .Specify offset distance:- 728 .To draw a ventilator type a command offset .Specify offset distance:- 631 .To draw a door section, type a command circle,offset and extend .To draw a toilet utilities, type a command circle,offset and extend and then trimmed it

Type a command D or dimension style managerS

.elect text height of 2.5,Precision of 0 and overall scale factor of 30 units

Type a command mtext

.Specify text height of 7.5 units

Dimensions of the above geometry is done with the use of command Dimension Linear

RESULT:- The above plan for toilet and utilities room is done with the use of commands such as 0ffset,Circle etc on AutoCAD 2022