Creating 3D Isometric view of various structural elements in AutoCAD

1 ans:-   1 AIM:- MODELA CEILING FROM THE ARCHITECTURE TAB ABOVE THE WALLS AT THE FIRST FLOOR LEVEL    INTRODUCTION :- <!-- [if !supportLists]-->·         <!--[endif]-->CEILING VERY IMPORTANT IN BUILDING <!-- [if !supportLists]-->·         <!--[endif]-->CEILING IS NOTING BUT  SLAB PROCEDURE:- <!--…

   PROJECT-2 AIM:-  To Create The 3D Rendered module of residential building  using proper views and rendered views INTRODUCTION:- I created a 3D Rendered module of residential building using AUTOCAD 2023. I am using proper layers and commands while creating the module I am using lot of tools while…

1 ans:- STATIC ANALYSIS Static analysis can only be performed if the system being simulated does not depend on time,and if the loads being applied are constant. Static analysis don't consider inertia. Static refers to the force that has constant size,position and direction on or within a structure  There is no necessity…

1(a) ans :-  Its from of flexural failure due to reversal of stress during earthquake. During stress reversal , support top experiences compressions and bottom experience tension  Top compression is managed by slab advantages, bottom tension was not satisfied by the provided reinforcement. Since the reinforcement…

1.1 DEAD LOAD LIVE LOAD WIND LOAD EARTHQUAKE LOAD 1.2 THE RATIO OF LONGER SPAN AND SHORTER SPAN IS GREATER THAN 2 IS CALLED ONE WAY SLAB WHERE Ly/Lx >2. WHERE LOAD ACTING ON TWO DIRECTION IN A SLAB IS CALLED ONE WAY SLAB. 1.3 UNIT WEIGHT OF STRUCTURAL STELL IS 7840 Kg/m3 UNIT WEIGHT OF SOIL IS 18 KN/m3 1.4 CIRCULAR…

1.1 GO TO THE PROPERTIES > DEFINE SECTION > CIRCLE. 1.2 OPEN STAA.pro SOFTWARE > CHOOSE UNITS SYSTEM > ENGLISH/METRIC. 1.3 LENGTH HEIGHT WIDTH OF BAYS ALONG THE LENGTH OF BAYS ALONG THE WIDTH OF BAYS ALONG THE HEIGHT 1.4 IS 456:2000 IS 13920:2016 IS 800:2007 1.5 GO TO DESIGN > DEFINE DESIGN PARAMETERS > SPECIFY THE COMPRESSION…

1.1 To Import a STAAD.Pro (*.std) File Select STAAD Importfrom the backstage. The Import from STAAD.Pro dialog opens. Click [...]in General settings to browse and select a STAAD.Pro (*.std) file to import. Select Use Mapping Filein Section Mapping settings, and then click [...] to…

1 ANS: 2 ANS: 3 ANS: 3 ANS: 4 ANS:

1 ANS: 2 ANS: 3 ANS: 4 ANS: 5 ANS:  

1 ANS: 2 ANS: 3 ANS:

1 ANS : LAYOUT OF KITCHEN FILE ATTACHED BELOW 2 ANS: 3 ANS:

1 ANS: 2 ANS: 3 ANS:   4 ANS: 5 ANS:

PROJECT-1 AIM :- TO  CREATE AN OWN ARCHITECTURAL DRAWING CONSISTING OF FLOOR PLAN ,ELEVATION AND SECTIONS FOR THE PLOT SIZE 60’X20’ (18.3mx6m) AND ALSO CREATE THE STRUCTURAL DRAWINGS FOR COLUMN,FOOTING AND BEAM. EXPLAIN THE PROCEDURE STEP BY STEP AND DISPLAY THE RESULT.   INTRODUCTION:- AUTOCAD IS…

SKETCH OF G+1 FLOOR RESIDENTIAL PLAN , TO VAASTU SHASTRA  AIM OF THE PROJECT :-  To sketch a G+1 floor residential plan according to vastu shastra and list down the names of structural drawing  required to be provided to the site for construction. To assume the size of structural elements [column , beam…

               PROJECT ON  CONCRETE MIX DESIGN FOR VARIOUS GRADES OF CONCRETE    DATA REQUIRED FOR CONCRET MIX DESIGN Grade of concrete Maximum size of aggregate Minimum cement content Maximum w/c ratio Workability in terms of slump Exposure condition Maximum temperature…