Analysis & Design of RCC shear walls in the model using ETABS

The architectural drawings of a G+3 RCC building is provided. The following information on the building is to be used: Location - Guwahati, Assam Function - Hostel block in an academic institute Aim: To provide the analysis in ETABS and Safe for the given hostel building Step 1: 1) Click File and select new model 2) Choose…

Given: Column size = 400 * 400mm SBC = 150kN / m * m ^ 2 Compression axial load = 2000 kN fck = M25 Steps to design a square footing: 1) Size of Footing 2) Net upward Pressure 3) Bending moment 4) Depth of Footing 5) Reinforcement 6) One way and Two-way shear Step 1: Size of Footing: Load on column = 2000kN Add 10% of…

QUESTION: The architectural drawings for a G+7 residential building in zone 5 has been provided. The floor plan is the same for all 7 floor levels. Possible column positions have also been provided. Conceptualize a framing plan layout and then model the building in Etabs. The following architectural drawings have been…

Aim: To run the analysis and design the RCC shear walls shown in the etabs model. Step 1: 1) Open the ETABS file 2) After the analysis click Concrete frame design Step 2: 1) Need to check there is any failures occurs 2) Click Shear wall design tool 3) select Display info and choose PM failure Step 3: 1) Click any wall…

Answer: Aim: To Providing details of longitudinal reinforcement for the two columns from foundation to terrace level. Step 1: 1) Open a G+4 Etab file 2) Click the Concrete Frame Design tool 3) Select the Display Design Info option 4) Choose design output as Longitudinal Reinf cement Step 2: 1) After Selecting the Longitudinal…

Detail design of beams in Etabs 2018. The ETABS file for a G+4 building is provided. Run the analysis and design the RCC Moment ResistingFrame. The following challenge deals specifically with two continuous beams in the 1st floor. 1) 3 span continuous beam along grid A 2) 7 span continuous beam along grid 3 Address the…

a) Effect of mass on T: Compare fundamental natural periods of buildings H, J and K. Have the buildings become more flexible or stiff due to change in mass? Aim: To Compare fundamental natural periods of buildings H. Jand K. using ETABS Procedure: Building H: Step 1: 1) Click the Define tab and click section properties.…

6. AIM:-MODELLING A 25 STOREY BUILDING IN ETABS. DATA:- Beam Size= (300 X 400) mm. Column Size=(800 X 800) mm. . Slab Thickness= 150 mm. Height of storey= 3m. Height of plinth= 1.5m. STEPS STEP-1 Open ETABS 2019. Go to file menu and select new model, a pop up window of model initialization will be opening Select use built…

Question 1:- As the structure is more restrained it will be more shrinking, expanding and cracking. There will be more floor shrinkage and expanding in structure A whereas there will be minimum cracks in structure B and C The shear walls in the structure also decide whether the floor vibration is more or less in the structure…

Question 1:-  Ans:- There are different factors to be considered for the conceptual design for structures resisiting earthquakes. STRUCTURAL SIMPLICITY: it is defined as the availablity of direct paths for transmission of loads from the different paths of the structure to the foundation, in this layout we can…

3.  

1.  The structure can be analysed by any of the standard methods including moment distribution  Given the degree of freedom is 3.       2.       2a.     2b.    3.      4.   

1) What is the mode of failure or damage of the beams in the figure above? Would you characterize the case as damage or as a failure? Are the damages repairable? Elaborate.   a)   This crack will be formed due to the flexural failure of a beam. The flexural strength, known as modulus of rupture, bend strength,…

1) Use the Architecture/ Structure Project file developed by you in Week 6 to 8. Export the Revit architecture and structure model to Navisworks Cache file following the export settings discussed in classAIM:- To export the Revit architecture and structure model to Navisworks Cache file following the export settings.INTRODUCTION:Navisworks…

1) Using Dynamo create a set of sinusoidal points and create a curve and create a surface out of the curve. AIM: To create a seet of sinusoidal points and create a curve and create a surface. out of the curveTOOLS USED:DynamoCode blockRange Math.sin.Integer sliderProduct (*).Add (+).Points by coordinate ListSurface by…

1) Use the shortcut keys in Revit discussed in class to complete the following tasks and list them belowa. Using 3D model create a section boxb. To create similar doors and windows in a floor plan layoutc. To reduce the thickness of lines visible in plan viewsd. To apply override settings to a floor in the model section…

1) What are HVAC systems? Why are they essential in the modeling of buildingsA) HVAC Systems:HVAC systems are responsible for the regulation of heat, airflow, ventilation, and air conditioning of an entire building. You won't see the machines when you enter the building but you will most certainly feel the effects of a…

1) Select the type of structure you want to build from one of the three below:a. Multi-Unit Residential Apartmentb. Office BuildingsC. SchoolAnswer:School   2) Assume reasonable assumptions for geographic and location details for your project modeling. Based on assumptions and type of structure selected identify the…

1. Open an architectural template. Using the Manage tab set project base point and project shared coordinates for the project.StepsOpen architectural template in Revit 2021.Select the grids option from the Architectural tabDraw the grids one in horizontal direction and one in vertical direction Go to the manage tab, select…

1) Why are building codes or standards essential for the modeling/efficiency of drawings in Revit?ans) A building code (also building control or building regulations) is a set of rules that specify the standards for constructed objects such as buildings and nonbuilding structures. Building codes specify minimum standards…

1) Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level.AIM: To model a Ceiling from the architecture tab above the walls at the first-floor level.INTRODUCTION:The creation of Ceilings within Revit is a very similar…

1) Use the project file created from Week 2. Use it for this assignment. Based on your layout from week 2, using floor tool under architecture tab and select the floor with appropriate material and thickness using the property browser create a layout in the Ground floor Level. Align the floor plan with grids created from…

1) What is BIM? Summarize the features of BIM and benefits of using BIM over 2D CAD tools.A) Building Information Modeling(BIM):BIM is an acronym for Building Information Modeling or Building Information Management.It is a highly collaborative process that allows architects, engineers, real estate developers, contractors,…

1). From the file menu, create a new project (Structural/Architectural/Construction template) and name the project appropriately.AIM:To create the new project(structural/Architectural/Construction template)and name of the project appropriately.INTRODUCTION OF REVIT.Revit architecture is designed to accommodate variousways…

3Dimensional Model of the Residential BuildingAim:To create a 3Dimensional model of the Residential Building and create a Render ViewGeneral Information: To Create a 3Dimensional model of the Residential Building i have drawn a random plan of size 10000X8000 Sq mm which have a required rooms the plan and Elevation details…

INTRODUCTION-COMMANDS USEDFOR DRAWING THE 3D OBJECTS ARE AS FOLLOWS.Extrude- Location: Draw > Modeling > ExtrudeThis AutoCAD 3D Extrude command allows the user to create a 3D object by extruding a 2D face along a line or path.Sweep-Location: Draw > Modeling > SweepThis command helps the user to extrude the…

Commands used:1. Extrude.2. Offset.3. UCS.4. Box.5. Union.6. Subtract.7. Move.8. 3d orbit.9. Loft.10. Sweep.11. Cone.12. Region.13. Boundary. PROCEDURE:Open the AutoCAD, click on workspace switching and change it to 3d modelling and click on the home button near the view cube.Set the limits and zoom-all.DRAWING OF 3D FURNITURE…

1. AIM-TO CRETAE LAYOUT OF PLAN AND SECTION OF THE PROJECT IN CHALLENGE 7 AND CREATE THE LAYOUT USING THE M-Arch TEMPLATE USING THE GIVEN DIMENSIONS AND PROPER SCALE.STEPSOpen the drawing of plan and section which is already drawn in the challenge no 7.In the left corner of the auto cad there is the tab named model.…

1. Aim: To create the layout of the kitchen and providing hatches to it using the autocad in detail.Introduction:kitchen layout is the most important part of designing your perfect kitchen.It's the layout that will determine how you cook, how you eat and how you socialise. So whether you're totally remodelling the…

1. Aim: To create:1. Template, inserting text and attributes2. Doors of warehouse and placing it in blocks3. Electrical legend and making it blocks4. Different types of door for residential project5. Drawing bars, making it as block and making it as a table as bar bending schedule.Commands used:1. Block.2. Insert.3. Attributes.4.…

AIM: TO DRAFT THE PLAN IN THE PLOT SIZE 60'X20' AND SKETCHING PLAN, ELEVATION, SECTION, LAYOUT OF BEAM, LAYOUT OF COLUMNS, LAYOUT OF FOOTINGS OF THE PLAN. INTRODUCTIONFOLLOWING TOOLS IN THE AUTO CAD ARE USED TO DRAW THE DRAWINGS:1. Line: Draw lines in AutoCAD2. Polygon: Draws polygons with three or more sides3. Rectangle:…

AIM-TO DRAW PLAN ELEVATION AND SECTION OF THE HOUSE IN AUTO CAD.INTRODUCTION- Commands used for drawing the plans and drawings below are as follows1. Line: Draw lines in AutoCAD2. Polygon: Draws polygons with three or more sides3. Rectangle: Used to draw rectangles4. Circle: Command used to draw circles5. Ellipse: Used…

1.AIM:To Draw the elevation and details of a wardrobe as shown in the Figure below. After sketching and to provide the dimensions and text with the use of layers.PROCEDURE:STEP 1:Units are set to mmLimits and lim-max are also setZoom command is also usedSTEP 2:In the command line type rec-2800, 2600In the command line…

1. Column Schedule INTRODUCTION1. Column C1 is provided with 4 bars of 20 mm dia. and 6 bars of 12 mm dia. The 12 mm dia bars are marked with 'a2. Column Cla and Column C3 are provided with 12 bars of 16 mm dia bars.3. Column C2 is provided with 8 bars of 20 mm dia and 4 bars of 12 mm dia. The 20 mm dia bars are marked…

Aim: To draw the given residential plan in detail.Introduction:Residential Layout is ideal for students and practitioners of urban design, planning, engineering, architecture and landscape seeking a comprehensive guide to the theory and practice of designing and laying out residential areas.Commands used:Limmax commandLimits…

AIM: To draw the given sketches in autocad.INTRODUCTION: autocad offers various tools like rotate,chamfer.fillet,move,offset etc to ease thr sketching process.PROCEDUREDRAWING 1:1.Open new file and set decimal and precision to 0.00.2.Command line: From random point draw 3.00 m line and @2.12<45, @2.83-135 then 2.00m…

Cross section of load bearing wall over spread footing.Aim: To draw cross section of wall over footing.Commands used:Line.Rectangle.Trim.Procedure:Step:1 - Create rectangle by typing "REC" in command boxSpecify the first corner point as (5,5)Specify the length of rectangle =0.9 units in command boxSpecify width of rectangle…

AIM:To Create a the geometries from P1 to P2 using all the coordinates system methods.INTRODUCTION:In this Challenge we create a basic drawings that followed by given dimensions using all coordinates system and the help of Line and Circle Command.Use the Imperial Template and the Decimal Units to draft the features.  …

AIM: To sketch a plan of G+1 floor residential building according to Vaastu Shastra and listing down the names of the structural drawings required to be provided to the construction site.INTRODUCTION TO VAASTU SHASTRAVastu Shastra is the Ancient Indian Science of architecture and acts as a guideline to design your home…

Aim: Mix design for M 35 grade concrete with fly ashProcedure:Step :1Stipulations for proportioninga. Grade designation : M35b. Type of cement: OPC 43 grade conforming to IS 8112c. Type of mineral admixture: Fly ash confirming to IS 3812 (Partd. Maximum nominal size of aggregates: 20mme. Minimum cement content: 320 kg/m^3…