a new title

Transmission belt link= https://drive.google.com/open?id=153lC_L4bbcVwGI3bvD0-a-LKvMxIqZvJ

Explanation= the tools and features used to create the belt is :

1. Sketching
2. Use of sketching constraints ( tangent , coincident constraints)
3. Smart dimensioning
4. Use of offset tool to offset the figure externally by 3.5 mm
5. The extrude by 88.00 mm
6. Fillet of 1mm on the side edging externally only.

in this way first i sketched the conponent and then using offset tool made a copy of my existing sketch about externally about 3mm , and then with the use of extrude command the 3-d component wad made after ,that fillet tool was used and by intelegent suface selection i selected upper palne surface so that all the external side edges was select and fillet was performed on the edge sucessfully.

KICK STAND CAD PART=https://drive.google.com/open?id=1ArrpbXtn_9CAlQUR2Rybxf2DBiHn_JFN

EXPLANATION= THE PROCEDURE TO MAKE a model IS ILLUSTRATED IN THE IMAGES BELOW ,And the tooling features are :-

1. fundamental to create an ellipse on the front plne and apllying constraint and using smat dimenssion provide necessary dimenssion .

2.now sketching of a spline on the mid/ right palne (the spline is straight angled in the leftward direction) with desired dimensiion and also there is , need to edit the lower points of splines

3. by creating a plane on the end point of the spline we have to draw an another ellipse (dimenssions anr in image) .

4. using of lofted/boss base command join the those ellipse using spline as centerline parameter ..

5. using dome command on both the ends ..

6. using cut extruse command to make a slot on the upper end for mounting on the chopper, the cutting slot dimenssion was 28*8 mm.

7. then creating a mounting boss/ cylindrical body inside the splitted face of upper end using sketch and bos extrude.

8. using fillet tool to provide fillet on the side edging of mounting side of kick stand.

In this way i created the kick stand followed by the videos instruction and some of my own understanding .all the dimenssions are illustrated on the images . and the images are self explanatory.

FRONT FENDER CAD PART= https://drive.google.com/open?id=1QyMQ1515AgIqmpfuOaoiisAY6CCyFeL4

EXPLANATION = the images shown for the suport of dimenssing and tooling features in solid works. and the procedure used to make front fender is as follows:-

1. using revolve command the component is modeled very easily ... firstly the sketch was created based on the dimenssion aquired from the pdf file attached to the video lectures.

2.the sketch was sketched on the front plane , along with a referance axis was drawn for performing an command of revolve.

3. The components was not fully revolved ,as it is a front fender we have to provide the direction of revolving in both left and right direction i.e, 5 degree and 130 degree.

4.on the center plane we have to create a sketch as shown in the image , the dimensions are given, here we used dynamic mirror option to create similar spline on both side .using this sketch we had to make / split the upper end of front fender to give a fancy look.

5. using split tool , split the revolve geometry. as shown..

6. again we are creating the splined sketch on front/ vertical plane for extrude cut the lower part of fender to make it fancy .

7. The using fillet command providing a 10mm fillet on the side edges .

In this way i created the model of front fender.

REAR FENDER CAD MODEL=https://drive.google.com/open?id=1NlJ83BAsssD1fvSPvAK-KuG4uKmVFdLu

EXPLANATION= THE SKETCHES AND DIMENSSIONS ARE ILLUSTRATED BY IMAGES THAT I CAPTURED FROM MY CAD FILES .. AND THE PROCEDURE TO MAKE REAR FENDER ARE AS FOLLOWS :-

1. FIRSTLY CREATE A SKETCH ON THE FRONT PLANE DEPENDING ON THE DESIRED DMENSSION ,AS MENTIOND ON THE PDF PROVIDED ALONG WITH VIDEO LECTURES .THE SKETCH IS THEN NEED TO BE REVOLVE .. THE CONSTRUCTION LINE IS THE REFERANCE LINE FOR THE REVOLVING ACTION.

2. WE HAVE TO SPECIFY THE DERECTION OF REVOLUTION IN BOTH THE DORECTION AS 10 DEGREE AND 140 DEGREE .

3. THEN BY SELECTING CENTER PLNE/ TOP PLANE , DRAW A SKETCH OF SPECIFIED DIMENSSION SHOWN IN IMAGE.

4. BY USING CUT EXTRUDE , CUT THE UPPER PORTION OF THE FENDER (ONLY THE PORTION WHICH WAS INTERSECTING).

5.THEN USING FILLET , APPLY A FILLET OF 45 MM RADIUS ON THE CORNER EDGING .ALSO USE FILLET OF 4MM RADIUS BY SELECTING UPPERMOST SURFACE OF FENDER, SO THAT THE UPPER SIDE EDGES GET SMOOTH.

6.THE USE SHELL OPTION TO CREATE A SHELL INTERNALLY IN THE LOWERMOST REGION (4MM)

7. CREATING A PLANE OVER CENTER PLANE OR TOP PLANE BY THE OFFSET DISTANCE OF 400MM , ANDCOPY FANCY TATTOTED DRAWING PROVIDED ,IN THE LINK SHOWN IN THE PDF.

8. PROJECT THAT SKETCH ON THE UPPER SURFACE OF FENDER ,AFTER ALLIGINING IT PROPERLY WITH THE CENTERLINE .

9. USING SPLIT SURFACE PROJECT THE CUT ON THE FENDER AND BY APPERANCE OPTION MAKE OT WHITE COLOUERD.

BY THIS WAY I CREATED THE REAR FENDER .

ALL THE COMPONENTS I CREATED BY TAKING A REFERANCE OF VIDEOLECTURES , PDF FILE PROVIDED ALONG WITH VIDEOS AND ALSO MY PREVIOUS CAD MODELING EXPERIENCE..