To Model the Chassis and Engine
- Chassis
https://drive.google.com/open?id=1JaVqidjdvvTjdnyGhNPvib6ewVt1TDEu
Features:
- Draw 2d sketch
- Extrude
- Extrude Cut
- Thin Extrude
- Revolve
- Revolve cut
- Mirror
- Sweep
- Dome
- Fillet
- Chamfer
- Projected curve
Steps Involved:
- Create new part
- Insert the 2d sketch picture
- Rename it to blue print chopper
- Draw 2d sketch accordingly
- Go to feature > curve > projected curve > select both curve > ok
- Create another projected curve
- Feature > swept boss/base > select curve which is created > ok
- Mirror it across the midplane chassis select the feature which we have created
- Draw the 2d fully defined sketch accordingly
- Feature > extrude > 22mm reverse
- Feature > extrude cut > upto next > ok
- Next apply chamfer of distance distance 90mm and 44mm
- Apply 25 mm fillet to the outside edges
- Create reference plane from the midplane chassis to the vertex
- Go to feature > swept boss/base > select the path > click ok
- Feature > extrude > 223mm > ok
- Apply dome of 10mm
- Create new reference plane to the end of the spline
- Go to feature > swept boss > select the path click ok
- Then split the remaining body
- Again create reference plane to the end of the spline
- Go to feature > swept boss > select the path > ok
- Again use split tool to cut the bodies
- Go to feature > revolved boss > select the construction line > ok
- Again use split tool to cut the remaining bodies
- Go to feature > boss extrude > select direction 1&2 > upto next > ok
- Apply 2mm fillet
- Feature > extrude > offset 165mm > for direction 1 > midplane extrude of 10mm > ok
- Again use split feature to cut the bodies
- Apply fillet of 20mm and 1mm radius
- Mirror it across the midplane
- Combine all three
- Apply 3 mm fillet
- Insert reference plane up 308mm
- Change the appearance to painted car sienna
- Engine
https://drive.google.com/open?id=1WLIe5O-HClHdvewLtW6h_JbOGqPw2l6_
Features:
- Draw a 2d sketch
- Extrude
- Extrude cut
- Thin extrude
- Chamfer
- Projected curve
- Linear pattern
- Circular pattern
- Fillet
- Mirror
- Dome
- Sweep
Steps Involved:
- Create new part
- Insert the sketch picture
- Draw the sketch
- Go to feature > extrude boss > midplane extrude of 200mm
- Feature > select circle > from surface > 50mm
- Feature > extrude 80mm circle > surface > blind 40mm extrude
- Go to feature > boss extrude > midplane > 150mm
- Apply fillet of 50mm
- Draw the 2d sketch
- Go to feature > revolve > ok
- Turn on temporary axis
- Again make the revolve about the temporary axis which we have created
- Draw a 2d sketch
- Make the circular pattern of 40 instances on the circular edge front pulley
- Make the circular pattern of 44 instances on the rear pulley
- Make the circular pattern of 12 instances on the front pulley
- Go to feature > cut extrude > offset of 250mm > offset from surface > select dome face > offset it 3mm
- Repeat it for another pulley
- Apply chamfer of 3mm and 45 deg
- Apply 1mm fillet to the all open edges
- Draw the 2d sketch
- Go to feature > boss extrude > midplane extrude of 150mm > ok
- Again go to feature > boss extrude > select small area > midplane extrude of 110mm > ok
- Draw 2d sketch on the reference plane which we have created
- Go to feature > extrude > upto vertex > ok
- Feature > boss extrude > blind of 125mm > ok
- Now apply the chamfer of 90mm amd 15mm
- Apply the fillet of 15mm the all edges
- Draw the 2d sketch
- Go to feature > extrude cut > offset of 26mm > direction1 8mm > ok
- Do the linear pattern spacing of 16mm and no of instances of 14
- Apply 2mm fillet to all internal and external edges
- Apply 10mm fillet
- Apply 5mm fillet
- Extrude > 2mm > ok
- Apply dome of 2.5mm
- Go to feature > extrude > midplane > 20mm
- Apply 10 mm fillet
- Use split tool and cut the bodies
- Go to mirror > select body > across right plane > ok
- Apply 25mm fillet
- Apply fillet of 5mm
- Feature > extrude > 15mm
- Go to feature > select bodies > upto next > ok
- Apply fillet of 2.2mm
- And do the circular pattern of 21 instances on the face
- Apply chamfer of 24mm and 75mm to the base edge
- Apply chamfer of 5mm and 45deg
- Create swept boss
- Mirror it across the right plane
- Create new reference plane
- Go to feature > swept boss > select 45mm circle
- Do the revolved boss across the construction line
- Apply 5mm fillet
- Go to feature > extrude cut > offset from surface > 2mm
- Draw a 2d sketch
- Go to feature > curves > projected curve > select 2 sketches > ok
- Make another projected curve
- Make both curves as composite curve
- Go to feature > swept boss > select composite curve > ok
- Similarly make another composite curve for another exhaust