MBD Simulation on a Piston Assembly

Abstract In this project, the main objective is to perform a buckling analysis on a cyclonic separator stand by creating a metallic stiffener on the legs of the stand and run the analysis to find out the change in buckling factor of safety. Once we find the buckling factor of safety, we run a design study…

The link to my project on Centrifugal pump design and analysishttps://projects.skill-lync.com/projects/Centrifugal-pump-design-and-analysis-01661 

The link to my project on Centrifugal pump design and analysishttps://projects.skill-lync.com/projects/Centrifugal-pump-design-and-analysis-01661 

Abstract In this project, the main objective is to compare the bending performance of the three types of beams(Rectangular beam, I -section beam, and C-section beam) which is extruded to a length of 400mm. After which, a baseline simulation is run on these beams at an external force of 1500N acting upon their smaller…

Abstract In this project, the main objective is to model an IC engine valve train which consists of essential parts such as a cam, push rod, rocker arm, valve mount, and valve, then assemble them in SolidWorks. Then run the motion analysis to find the contact force encountered between the parts(between cam and…

Abstract In this project, the main objective is to model a piston and its associated parts i.e. piston head, wrist pin, connecting rod, end cap, and crank then run an MBD simulation on that. Motion analysis is done at 1200rpm and frame rate 7200fps with precision contact for three different parameters then plots of…

Abstract In this project, the main objective of this project is to model a planetary gear which consists of a ring gear, a sun gear, four planetary gear, and a carrier. After assembling the gears and the carrier we will be running a motion analysis at 200rpm for various parameters. Then plot the angular velocity graph…

Multibody Dynamics using Solidworks Abstract In this Project, Creating a 3D part of Driver and Driven from scratch and will be setting up the motion analysis for an Internal Geneva Mechanism at 10rpm and 20rpm with 60 frames and 120 frames respectively. Then obtaining the plots of Contact force (between driving and…

Abstract In this Project, Creating a 3D model of a Centrifugal pump, run a baseline flow simulation where inlet flow takes place and then perform a parametric study for different velocities. Showing the Performance diagram and Obtain the relationship between Pressure ratio and mass flow rate and explaining the results. …

ABSTRACT In this Project, Creating a 3D model of a flowbench and run flow analysis where the internal flow takes place and running a baseline simulation and then performing a grid dependency test(4, 5 & 6) at a particular valve lift(0.003) and also performing valve lift(0.001 -0.008) test at a particular grid size(5).…

ABSTRACT In this Project, CFD analysis of a cylinder in which external flow takes place and running a baseline simulation and then calculating the Reynolds number and also the simulation end time. Then increase the Reynolds number by a factor of 20%, 40%, and 100% then run the transient flow simulation. Animations for…

*********** Comments by Grader ************ GOOD JOB !!!! SUGGESTION : The other thing that you can do is to attach the code and images in projects.skill-lync.com  and paste the link over here. If you have any…

Flow over an airfoil-Flow simulation using SOLIDWORKS Abstract  In this Project, CFD analysis of the two-dimensional subsonic flow over a NACA 0017 airfoil at various angles of attack and compare the lift and drag force. The geometry of the airfoil is created using SOLIDWORKS. CFD analysis is carried out using Flow…

Pipe Flow Simulation Using SolidWorks us Flow Simulation. Introduction The purpose of this study is to simulate flow in pipe utilizing SolidWorks software.SolidWorks add-ins enable you to simulate the flow of liquids and gases and efficiently analyze the effects of fluid flow. The motion of a fluid is usually very complex.…

Parsing NASA Thermodynamic Data Introduction: File Parsing is the process of analyzing a string of symbols, either in natural language, computer languages or data structures, conforming to the rules of formal grammar. Within computational linguistics the term is used to…

Solving second order ODEs In Engineering, ODE is used to describe the transient behavior of a system. A simple example is a pendulum The way the pendulum moves depends on the Newtons second law. When this law is written down, we get a second order Ordinary Differential Equation that describes the position of the "ball"…

Genetic Algorithm The genetic algorithm is a method for solving both constrained and unconstrained optimization problems that are based on natural selection, the process that drives biological evolution. The genetic algorithm repeatedly modifies a population of individual solutions. At each step, the genetic algorithm…

Forward kinematics of a 2R Robotic Arm A program to simulate the forward kinematics of a 2R Robotic Arm. A 2R Robotic Arm consists of two links and two rotational joints. From Fig.1. we can come to a basic understanding of 2R Robotic Arm. Solution: Step 1: Calculate the position of link 1. To calculate the position…

%A program to calculate the Drag Force on a Bicycle and incorporating a function to plot Velocity v/s Drag Force: %Matlab program to calculate drag force against a cyclist clear all close all clc %inputs %Drag coefficient c_d = 0.8; %Frontal Area (m^2) A = 0.1; %Density (kg/m^3) rho = 1.225; %density of air %velocity (m/s)…