Curve Fit for Specific Heat v/s Temperature Data

https://skill-lync.com/student-projects/cfd-analysis-of-flow-over-naca-0017-airfoil-at-different-angles-of-attack

In this project, simulation of flow over NACA 0017 airfoil is performed using Flow Simulations add in of Solidworks. To generate the co-ordinates of NACA 0017, the following data was fed into NACA 4 digit generator of airfoiltools.com These co-ordinates were copied into a text file, a column with all rows zero was added…

In this project, transient 3D simulation of flow of air over a cylinder of diameter 0.02m and length 0.2m is performed using Flow Simulations add in of Solidworks. The cross-section of the cylinder is in the XY plane, while its length is in the z direction. The free stream velocity is in the X direction.Initial studies…

Introduction In this project, the effect of Reynolds Number on the flow through a pipe is studied through numerical simulations using Flow Simulations add-in of Solidworks. Simulations are carried out for flow of water through a pipe of internal radius 2.5cm and length 20cm. The boundary conditions are as follows:1. Inlet…

Using the Taylor Table method, the fourth order approximate finite difference scheme for the second order derivative has been derived for 3 different stencils. 1. CENTRAL DIFFERENCE SCHEME To derive the fourth order approximate central difference scheme for the second order derivative, we use the following formula: `n…

https://projects.skill-lync.com/projects/Parsing-NASA-Thermodynamic-Data-File-40140 

https://projects.skill-lync.com/projects/Parsing-NASA-Thermodynamic-Data-File-40140 

https://projects.skill-lync.com/projects/Parsing-NASA-Thermodynamic-Data-File-40140 

https://projects.skill-lync.com/projects/Parsing-NASA-Thermodynamic-Data-File-40140 

https://drive.google.com/open?id=1-28PCT5HRlQSoPoEFY121-gaWV4sLUqp

Code: https://drive.google.com/open?id=1-q_GHG1Y846VIdfsx24CM0R838Sx6rDR Animation: https://drive.google.com/open?id=1wVRtw-zCApnSLfnLd4nra6IUg1C8GhYz

https://drive.google.com/open?id=1nKZirzSCYHg-5l2Ph6T2XCzI9G6gVivw

https://drive.google.com/open?id=1AVNVASkt5cdHHGyaoCko79m1IBf6aVNg

Linear Fit: https://drive.google.com/open?id=10caV0tPqrpUk3mSv5YTUHq1uFNBbtLXx Cubic Fit: https://drive.google.com/open?id=14Ol6VVrc_GtuS_k2sQKVXZqAEHzXKbYp

1. What does popt and pcov mean? popt stores the values of the co-efficients of the polynomial passed to the function curve_fit. The      function curve_fit calculates these co-efficients and popt stores them. pcov : It is a 2D array which gives the estimated co-variance of popt. The diagonals provide…

https://drive.google.com/open?id=12IZepes07vJPxQwKd4h8Mv3ZaChGN0qK

https://drive.google.com/open?id=1recTSx6IS2fyp7-26HjQskfui2RSDb78

# Program to calculate the drag force import matplotlib.pyplot as plt # Drag force nd velocity \"\"\" Inputs \"\"\"c_d = 0.8A = 0.1rho = 1.2velocities = [5,10,15,20,25]F_d = []# Calculationsfor velocity in velocities: F_d.append((0.5*c_d*rho*A*velocity*velocity))#PLottingplt.plot(velocities,F_d)plt.xlabel(\'velocity\')plt.ylabel(\'Drag…

https://drive.google.com/open?id=1wf9ziXVN5D-HurOkp28qrbXU38p1CXWf

ODE Code: https://drive.google.com/open?id=13TiJg6xBHlESyC3l2ZoiSshhfGiCEr9Y ODE Function: https://drive.google.com/open?id=1StlMkK5oVNlIEl5go_DETbUnafO3rxDD   VIDEO: https://drive.google.com/open?id=1H1SpZY1UZ4YvtPLkV_F-7tL3MzCgJ3Tz  

% Drag Forceclear allclose allclc % Inputsdrag_coefficient = input('Enter the value of drag co-efficient:');rho = input('Enter the density of the medium(kg m^-3):');A = input('Enter the value of the frontal area(m^2):');v1 = input('Enter minimum veloity(ms^-1):');v2 = input('Enter maximum velocity(ms^-1):');v = [v1:v2];…

clear allclose allclc%Inputs gamma = 1.4; % Engine Geometric Parameters:bore = 0.1;stroke = 0.1;r = 12;con_rod = 0.15; % Calculating the swept volume and clearance volumev_s = (pi/4)*bore^2*stroke;v_c = v_s/(r-1); % State Variable at point 1display(\'Input state variables for point 1:\');p1 = input(\'Pressure:\');t1 =…

% Drag Forceclear allclose allclc % Inputsdrag_coefficient = input('Enter the value of drag co-efficient:');rho = input('Enter the density of the medium(kg m^-3):');A = input('Enter the value of the frontal area(m^2):');v1 = input('Enter minimum veloity(ms^-1):');v2 = input('Enter maximum velocity(ms^-1):');v = [v1:v2];…