Case Study: Thermodynamic Performance Analysis Of a Twin-scroll Turbocharger vs Single-Scroll Turbocharger Using GT-Power.

ABSTRACTThe impact of improvement in vehicle aerodynamics mainly reflects in lower fuel consumption and lower carbon dioxide emissions into the atmosphere. The governments of many countries support continuous aerodynamics’ improvement programs as a way of mitigating the energy crisis and atmospheric pollution. This…

ABSTRACTThe impact of improvement in vehicle aerodynamics mainly reflects in lower fuel consumption and lower carbon dioxide emissions into the atmosphere. The governments of many countries support continuous aerodynamics’ improvement programs as a way of mitigating the energy crisis and atmospheric pollution. This…

Title:- Geometry cleanup and meshing of an automotive hood for structural analysis   Objective:  Perform geometry cleanup of automotive hood (both inner and outer panel). Perform mid-surface extraction of both the panels and Hem both the surfaces . Perform shell meshing/grid generation of the following model…

Abstract: This project presents the Modelling of the  behaviour of  fluid and its properties when it passes through a convergent-divergent nozzle using a Finite Difference Method. However, to simplify the understanding of the dynamics of the flow in the nozzle, only 1-dimention flow variation has been considered…

 Turbocharger: Literature Review: A turbocharger is mechanical rotating device which forcebly induces air at high pressure into the internal combustion engine, in turn increases the power and effeciency (thermal and volumetric effeciency) of the engine. A turbocharger is the assembly of turbine and a compressor connected…

  (A) Problem defination:- Solve the following Linear equation using Gauss-Jacobi, Gauss-Seidal and SOR iterative method and understand the following parameters:- Spectral radius and the impact of spectral radius on the convergence of the solution. Effect of diagonal magnification on spectral radius for each iterative…

CASE STUDY:-  A Thermodynamic Analysis Of A Tractor Engine For Use In India With Given Engine Performance Targets. A Brief Literature Review: A tractor is an engineered vehicle specifically designed to deliver Power and traction/tractive effort to haul heavy equipments like agricultural and construction equipments.…

Solving 2-D 2nd Order Linear Transient &Steady  Heat Conduction Equation Using Both Explicit And Implicit Numerical Schemes In MATLAB.   Explicit Scheme : We say that a scheme is explit when the information at time level "n+1" depends on previous time levels i.e., "n , n-1" e.g. the upwind difference…

  CASE STUDY: Effect of Burn Rate on engine performance Of A 6-Cyl-Turbocharged-DI Engine Using A Non-predictive Combustion model (DI WIEBE) Abstract: Analytical functions approximating the burn rate in internal combustion engines are useful and cost-effective tools for engine cycle simulations. Most functions proposed…

Solving 1-D Linear Convection Using First-Order Backward Difference And Forward Difference method Using MATLAB LITERATURE REVIEW: WHAT IS CONVECTION? Convection is the sum of bulk transport of the  fluid  and brownian/ osmotic dispersion of fluid constituents from high density region to lower density region.…

Deriving the 4th order approximation for 2nd order derivative of a function using Taylor table for centered, skewed right-sided stencil and skewed left_sided stencil and compare the error results for the same using MATLAB.   Given function, f(x)    =  exp(x)*cos(x) The second_order derivative,  f\'\'(x) …

Objective:- (1) Determine the engine parameters running at 1800 rpm and record the same. (2) Further increase the power output obtained at 3600 rpm by 10%.   Model:-  The GT model Of the 1-cylinder engine is shown below:- Observations (@1800rpm):-   Air Flow Rate = 24.645 kg/hr. BMP (Brake mean effective…

Objective:- To mesh the geomety with different mesh element size and observe the                               meshed  geometry.   Geometry:-  Here below the manually cleaned up geometry of pressure-valve is shown:    …

OBJECTIVE:-   The main objective of the challange is to create a mesh model of a  cylinder                         geometry having element size of 1 unit.   PROCEDURE:   STEP 1:-   Open the geometry by clicking the FILE…