Assembly of American chopper
1.Gas Tank
-First, the Underlay image of the chopper is added to the midplane.
-Then a plane is created with respect to the front plane.
-After that, a sketch is drawn on the newly created plane and the midplane and is used to create a swept surface using the Sweep Surface tool.
-Now another sketch is drawn on the Bottom plane and is used to trim certain material using the Surface Trim option.
-Then another plane is created with respect to the Midplane and a sketch is drawn.
-Again make another plane and draw a sketch. Then draw another sketch on another plane that was created previously and using the two sketches make a projected curve.
-After that draw another sketch on the plane that was created previously and using the Surface Loft tool make a surface loft.
-Now make another plane with respect to the front plane and draw a sketch. After that draw, another sketch on the Bottom plane and these two sketches are used to create a projected curve.
-Then to make a boundary surface draw two sketches on the midplane and then using the Surface Boundary tool make it.
-After that using the mirror tool make a mirrored version of the part on the other side of the midplane.
-Now using the surface knit option knit together all the surfaces.
-Then for making the seat sketch the Bottom plane and the split line option is used to combine with the gas tank body.
-After that using the surface extrude option the seat is generated.
-Later some fillets are given to the seats.
-Again the boundary surface is created for the seat.
-Now a surface loft is made at the bottom of the gas tank using the loft option from the surface window.
-Then again using the knit option knit together all the surfaces.
-After that, some fillets are applied.
-Now draw a sketch on the midplane as well as on the plane that was created with respect to the front plane and using the cut sweep option cut the part.
-Then again fillets are applied and the whole part is made into a shell.
-After that, appearances are given to the part and the seat separately.
https://drive.google.com/open?id=13a-Ae5XVNs6Dx4PvBOZb1Jr9aLZw6wPl
2.American Chopper Assembly
-First, add all the parts that are created to the SolidWorks software and keep it open and then start assembling by creating a new assembly file.
-Then using the insert component option add the chassis to the window and then make a coincident mate using the mate option for the midplane and the front plane of the assembly.
-After that add the engine and make its bottom stand coincident withe the flat bottom surface of the chassis.Then make a distance relationship between the front surface of the bottom stand and the front surface of the holding part of the chassis.
-Now add the pedal to the window and make its two cylinders concentric with the holes given on the chassis and make it\'s one side coincident with the chassis.After that, the pedal is mirrored on the other side of the chassis.
-Then add the kickstand to the window and then make its inner surface coincident with the outer surface of the part that is on the chassis.
-After that give a concentric mate to the kickstand and the chassis.
-Now to limit the movement of the kickstand a limit angle is given to the kickstand.
-Then the transmission belt is added and a width mate is given to it with respect to the engine and also a concentric mate is given to it.
-After that, an angle is given to the transmission so that it stays fixed.
-Now the oil tank is added and is given a coincident relation between its face and the face of the engine near the seat. And again the coincident relation is given to the edge of the tank and the surface of the engine.
-Then another coincident relation is given with respect to the midplane of the tank and the chassis.
-After that, the rear wheel is added and is given a concentric relation between the chassis and the wheel.Now a coincident relation is also given between the midplanes of the chassis and the wheel.
-Now to make it fixed a parallel relation is given between the front plane and the side of the chassis just after the wheel.
-Then the rear fender is added and is made concentric with the disc of the wheel. And a coincident relation is given to the midplanes of the rear fender and the chassis.
-After that, a parallel relation is given to the front plane of the rear fender and the side of the chassis.
-Now the chain is added and is given a width relation between the one side of the chain link and the side of the sprocket.
-After that, the other side of the chain is fixed using the parallel relation.
-Then the gas tank is added and is given a distance relation between its front plane and the front plane of the chassis.
-After that certain coincident relations are given so that it aligns with the chassis of the chopper.
-Then the front fork is added and given a concentric relation between its axis and the chassis.
-After that, a width relation is given to the two surfaces of the fork and the chassis.
-Now the angle of tilt is limited using the angle relation between the plane of the fork and the chassis.
-After that, a parallel relation is given to the chassis and the fork so that whenever we want we can position it in a straight position.
-Then the front wheel is added and is given a concentric relation between the fork and the wheel. After that, the wheel is given a coincident relation between the planes of the wheels and the fork.
-Now the front fender is added and is given a coincident relation between various planes of the fender and the fork.
-And then save the document after rebuilding
https://drive.google.com/open?id=1D3q5VYcTeJSib5r6jmKaoJXa5UTEwr2y