3D Creation of Ceiling, Roof, Architectural plan, Structural plan, Sectional view, Elevation view and Camera specific view for a house plan using REVIT

Introduction: Dynamo is an open source visual programming language for Revit, written by designers and construction professionals. Its a programminglanguage that allows you to type lines of code;  while also creating an algorithm that consist of nodes.   Using dynamo work can be carried out with enhanced BIM capabiilities…

1) AIM:  To model a Ceiling from the architecture tab above the walls at the first-floor level. INTRODUCTION: The creation of Ceilings within Revit is a very similar process to that of Floors and Roofs- ie you can let Revit do most of the work and "gress" where you want the boundaries to be.Or you can enter Sketch Mode…

1) From the above the options of type of structure to build a building, i need to pick a multi-unit residential Apartment. 2)The geographical and location details for my project modelling, based on assumptions of multi-unit residential Apartment. selected identify the modelling requirements from NBC. 1.  As above mentioned…

1) PROCEDURE:  Download the NavisworksExporters2024.exe  set up file Open the Revit file which we want to export into Navisworks. In the file, the menu select Export followed by NWC Then the exporting process will begin as shown. Once it is exported open the exported file using the Navisworks manage application.   RESULTS: The…

  AIM OF THE PROJECT- Creating a 3D rendered model for a Residential Building in AutoCad.   INTRODUCTION- COMMANDS USED FOR DRAWING THE 3D RENDERED VIEW OF BUILDING ARE AS FOLLOWS. -         Extrude- Location: Draw > Modeling > Extrude This AutoCAD 3D Extrude command allows the user to create a 3D object by extruding a…

 3D ismoteric view of the building with plan and elevation is given below:   - Isometric view created is as follows:       2. 3D view of the building facade as given in the plan and elevation is as follows:     - Isometric view is developed as given below:   3. Isometric 3D…

1.AIM         To create a 3D Furniture elements using the various commands in Auto CAD. INTRODUCTION BY 3D VIEW The process of creating a mathematical representation of any surface of an object in three dimensions by using special software. A 3D model can even be represented as a two dimensional image…

AIM: To Create a layout of the plan and section A of the project in challenges 7 . PROCEDURE:  In the command prompt type units > mm> decimal In the command prompt type limax >100,100 In the command prompt type limits>0,0 In the command prompt type layout > template>Tutorial arch .m  In the command prompt type Ms to specify…

Aim: To Create the Kitchen Layout and to  Also, use proper dimension techniques to dimension the kitchen layout. Also, insert text wherever required. All dimensions are in mm. Procedure: step 1: units are set to mm limits and limax are also set  zoom comand is also used  Step 2: In the command prompt type rec and the dimensions…

AIM: To Create Custom1_titleblock and Custom2_titleblock using Attributes and block command from Autocad software . PROCEDURE: Step 1 ( custom1_tittleblock) In the command prompt type L to draw the lines  In ribbon tab > Annotate > Mtline ( to draft the text ) go to properties tab to change the colour …

AIM 1. Architectural drawing of a residential building: Plan of a residential building. Elevation of a residential building. Section of a residential building. 2. Structural drawing: Column plan layout of the building. Footing plan layout of the building. Beam plan layout of the building. Commands used: Line , Offset ,…

 1)Target mean strength f’ck =fck + 1.65s Where f’ck = target average compressive strength at 28 days fck = characteristics compressive strength at 28 days, and s = standard deviation 2)Cement content Cement content = water content / water-cement ratio 3) Volume Calculations (a) Volume of concrete (b) Volume of cement…

ANSWER OF THIS QUESTION IS SHOWN IN THE BELOW PDF 

    Draft analysis report for both the given Class-A surface and the final plastic component                     Solid model with the proper color code of the draft angle in various orientations                                                             REPORT   Report about draft analysis and the tooling axis creation…