INTRODUCTION: Curve fitting is the process of constructing a curve, or mathematical functions, which possess the closest proximity to the real series of data. By curve fitting, we can mathematically construct the functional relationship between the observed data set and parameter values, etc. It is highly effective in…

INTRODUCTION: Air standard cycles are quite important as they help us to understand the theoretical limits of a particular cycle ,which can be used to get an idea about the performance of IC engine. An otto cycle consist of following processes: 1.Isentropic Compression process(1-2) 2.Constant Volume heat addition(2-3)…

Introduction There are two links in a 2R Robotic Arm Manipulator and generally link 2 is smaller than the link 1. As the links start to move from origin both the links make a particular angle with respect to x and y axis respectively at a particular position. In this project we will write a program for animation…

                                   GENETIC ALGORITHM   A genetic algorithm (GA) is a method for solving both constrained and unconstrained optimization problems based on a natural selection process that mimics biological evolution.…

INTRODUCTION: Among ordinary differential equations, linear differential equations play a prominent role for several reasons. Most elementry and special functions that are encountered in physics and applied mathematics are solutions of linear differential equations ( harmonic motion). When physical phenomena are modeled…

Breaking Ice with Air cushion Vehicle - Find minimum pressure with Newton-Raphson method using python     Equation Used:   p = the cushion pressure h = thickness of the ice field R = size of the air cushion σ = tensile strength of the ice β is related to the width of the ice wedge   Given…

Flow over a cylinder  OVERVIEW: Using Flow Simulation in SolidWorks, flow over a cylinder was simulated at different Reynolds number. Objectives: To calculate the baseline case Reynolds number. To run a baseline simulation and then calculate the Reynolds number. Then increase the Reynolds number by a factor of 20%,…

                                  CURVE FITTING USING PYTHON   INTRODUCTION: Curve fitting is the process of constructing a curve, or mathematical functions, which possess the closest proximity to the real series of data. By curve…

  Flow over an airfoil    Objective:- 1) To find lift and drag forces at different angle of attack of NACA0017 aerofoil 2) For the different angle of attacks 0,2,4,6,8,10 compare the lift and drag forces.   THEORY: The angle of attack is the angle between a reference line on a body (often the chord…

 2R Robotic Arm Simulator using python OBJECTIVES: (1) To write a program simulate forward kinematics of a 2R Robotic Arm. (2) create animation of images of plots saved. There are two links in a 2R Robotic Arm Manipulator and generally link 2 is smaller than the link 1. As the links start to move from origin both…

    Air standard Cycle using python   INTRODUCTION: Air standard cycles are quite important as they help us to understand the theoretical limits of a particular cycle ,which can be used to get an idea about the performance of IC engine. An otto cycle consist of following processes: 1.Isentropic Compression…

INTRODUCTION: Among ordinary differential equations, linear differential equations play a prominent role for several reasons. Most elementry and special functions that are encountered in physics and applied mathematics are solutions of linear differential equations ( harmonic motion). When physical phenomena are modeled…

Rankine cycle Simulator using MATLAB   The Rankine cycle is the fundamental operating cycle of all power plants where an operating fluid is continuously evaporated and condensed. The selection of operating fluid depends mainly on the available temperature range.             …

  Centrifugal pump design and analysis   OBJECTIVES To create a geometry of a centrifugal pump and perform flow simulation using Solidworks To Obtain the relationship between Pressure ratio and mass flow rate.   INTRODUCTION Centrifugal pumps are used to transport fluid by conversion of rotational kinetic…

Pipe Flow SImulation in SolidWorks  Introduction:Carrying out fluid flow simulations in a virtual environment is a better suited approach. This allows the engineer to model the fluid’s behavior at every stage in the process and accurately predict how it will react in an actual casting environment. In doing…

                           FLOW OVER A BICYCLE Introduction: whenever you ride a bicycle you experience a force which resist motion of bicycle. This problem mainly arises due to wind resistance. In order to move further riders has to push further through…

          Data analysis using python OBJECTIVES: 1) Read data from file. 2) Checking for file compatibility 3) Plotting data column wise and saving them using file header 4) Plotting data from one column against data from another, labelling them using header data 5) Calculating area under a curve…

Parsing NASA thermodynamic data using MATLAB   (Parsing is reading and writing the data into the file to  use it.) OBJECTIVES: 1. Write a function that extracts the 14 co-efficients and calculates the enthalpy, entropy and specific heats for all the species in the data file. You will be reading this file NASA…