Initially 3 points are created with given co-ordinates as P0(0,0,0), P1 (0,-10,0) and P2 (-20,0,0) 2 cylindrical solids where created as rod1 (Connecting P0 and P1) and rod2 (Connecting P1 and P2) with diameter of 2m. 2 bodies were created for rod1 and rod2 and their mass and inertia properties where taken from the associated…

European Regulation Requirement for Wheel Arc:- Criteria to pass European Regulation Requirement :- To satisfy the European Regulations all the section should have clearance of 5 mm from the tire when viewed from top. Wheel Guard Requirement- The value of L should be more than 5 mm at a line 30 degree forward and 50 degree…

Undercoating is a protective layer that is applied to the under layer of a car where the parts are not coated with a protective layer of paint and thus more susceptible to rust damage. Seals on the underbelly parts have gotten a lot tighter and more effective at keeping out dust and moisture, but there are other factors…

1. .xml is recoznised by the Motionsolve.  2. just by changing the simulation type and setting we get huge difference in the results. Thus to get an accurate result one should know to select correct parameters. https://drive.google.com/open?id=1_F59gVYEe2b0GqmuUQAHJ9HuL8FIcM2h

Aim- To study the four bar mechanism of the bicycle frame with and without spring damper suspension system. Important criteria- The frame is fixed to the Ground Body. Force is applied to the point of contact between upper and lower link. Procedure- Initial 7 points are created to form the simplified model of the bike.…

Aim of the project -  For the given Roof styling, develop the essential flanges and reinforcements Do a curvature study on the roof and perform calculations to determine the position of the Bow-roof Check for Draft analysis Carry  section modulus on 0-Y section Roof design -  The roof is an essential part…

https://drive.google.com/open?id=18E4c7-QPyeRQYPbhcnj03ZNlVXLj7ovc In Dynamics analysis, the Dof is 1 and initial conditions is apllied in that Dof to measure force, displacement, acceleration etc. When you apply contrain to that one dof then the analysis becomes kinematic analysis.

Use compliant joints. use flexible bodies. use J-prims. combine with DOF with lower pairs joint.

*********** Remarks of the Evaluator ************Good Job! Your report is good! Keep up the good work!But please make a more detailed report, only the main graphs and a few important screenshots are required, and also make the images smaller as I can't see the entire image Regards,Thanuj Singaravelan SUGGESTION…

Aim- To study the mechanism of Geneva Drive and analyze its motion characteristics with the help of 3D contacts. What is Geneva drive- It is the most commonly used devices for producing intermitted rotary motion, characterized by alternate periods of motion and rest with no reversal in direction. The rotor carries a pin…

Introduction:- Bonnet is an important component of the front portion of the car which is used for many purposes. Bonnet is used to decorate front portion of the car and to add luxurious look. It is made aerodynamic in shape to reduce air effect. Generally it is used to cover car engine, radiator and many other parts, therefore…

Aim- To study the cam follower mechanism with the help of 3D contact. Important criteria: - Here gravity is used in negative y direction instead of spring to maintain the contact between the follower and cam. Procedure: - Initially each of 6 parts of the cam follower mechanism (i.e cam, follower, follower shaft, roller…

The Backdoor or Tailgate is the panel that covers the boot (or trunk) of an automobile. It enables access to the main luggage compartment. A hinge allows the boot lid to be raised, while devices such as springs or gas cylinders hold it up in the open position.   In principle, boot lids have to fulfil similar requirements…

The Backdoor or Tailgate is the panel that covers the boot (or trunk) of an automobile. It enables access to the main luggage compartment. A hinge allows the boot lid to be raised, while devices such as springs or gas cylinders hold it up in the open position.   In principle, tailgate have to fulfil similar requirements…

Aim - To carry out Automobile simulation on the road with different combinations of spring stiffness, damping ratio, and coupler ratio. Procedure:- Initially Front Suspenion System/Assembly is created in the model. All the necesaary pair body, points and joints are created to make the wheel and knuckle joint. 2 bodies-…

  Aim- To Study the effect of various parameter on Flexible Lower Arm and find the maximum displacement, stress and strain of the lower arm. Procedure- In the FlexBodyPrep, existing left lower arm h3d file was imported and mirrored along the Z plane to produce right lower arm. Once the arm are imported, with the help…

Aim- To study the mechanism of Geneva Drive and analyze its motion characteristics with the help of 3D contacts. What is Geneva drive- It is the most commonly used devices for producing intermitted rotary motion, characterized by alternate periods of motion and rest with no reversal in direction. The rotor carries a pin…

https://drive.google.com/drive/folders/1d8OhuXkCYRBsW1ChqpLO6rQLBB2p4xsv?usp=sharing

Simulate and plot a freefalling body (point mass) of mass 1 kg and inertial properties 1 kgm2 in the y-axis (gravity should be -9.81 m/s2 in the negative y-direction) (Use dimension of length in meters not mm) [60] Ans-  Mass And Inertia Properties Changing of units to meters Gravity Displacement Vs Time    …

Section Modulus is given by the formula:- S = I/y where, S = Section Modulus I = Moment of Inertia Y = distance between the nuteral axis and the extreme end of the object  Stainless steel AISI 302 is considered as material for the hood which is cold rolled with  y = 520 MPa.   Original Hood Design :-  …

To stop the trunk lid exactly when it comes in contact with the body we have to modify the motion curve which is applied to the joint. Changing the value to zero.  Resulted curve is shown.   No red area between trunk lid and body indicates there is no collision between them.  

google drive link - https://drive.google.com/file/d/1zbxQZTPfHccBmk-sm7SZRBLHBtxJ_CsF/view?usp=sharing