Full course · free on YouTube · 51 min

Dynamic Analysis with STAAD.Pro, free, 51 minutes

This is a single 51-minute recorded Bootcamp session by a Bentley Systems R&D manager, with Skill-Lync and Bentley introductions in the first six minutes. It covers dynamic analysis basics, seismic analysis to IS 1893 (Part 4) and forced vibration, with demonstrations in STAAD.Pro.

20 chapters · published 4 Mar 2022 · 4,223 views as of 19 Nov 2026 · by Skill-Lync

Free. We ask for your name and phone once before it plays here · or watch on YouTube ↗

Who is this course for?

Civil and structural engineers and students who already use STAAD.Pro and want to see how dynamic and seismic analysis of industrial structures is set up.

What will you learn?

  • Model masses as lumped loads in STAAD.Pro, using the classical or the reference load method
  • Explain why a Ritz vector solution can reach 90% mass participation in far fewer modes than natural mode shapes
  • Identify the four structure categories of IS 1893 (Part 4) and when Clause 10 requires dynamic analysis
  • Enter a custom response spectrum with CQC combination, direction factor, damping and scale factor
  • Combine earthquake components and use mass participation and mode shapes to spot asymmetry
  • Describe how a floor response spectrum, a synthetic time history and a steady-state check on a turbine foundation are produced

What does each part of the course cover?

8 sections, in watching order. Click a timestamp to jump the player there. Chapter titles are from the video description, lightly edited for spelling.

  1. 0:007 min · 4 chapters

    Introduction, Bentley partnership and session plan

    Housekeeping before the technical talk: an overview of Skill-Lync coursework, the Bentley software partnership, and the speaker from Bentley Systems. The speaker then sets the plan: a general discussion, mostly seismic analysis of industrial structures, then a short forced vibration part.

    Chapters
    • 0:00Introduction to Skill-Lync’s coursework
    • 1:54Skill-Lync’s partnership with Bentley and software access
    • 3:35Introducing the speaker, Bentley Systems R&D
    • 5:30Plan for the session: general dynamics, seismic analysis, forced vibration
  2. 6:497 min · 2 chapters

    Dynamic analysis basics and mass modelling

    Starts from the equation of motion and how STAAD.Pro solves it by modal superposition, which needs an eigen solution of the stiffness and mass matrices. Then covers mass modelling: masses entered as lumped loads in all three directions, with the classical and the reference load methods shown on a model.

    Chapters
    • 6:49Equation of motion, modal superposition and the eigen condition
    • 10:14Mass modelling in STAAD.Pro: lumped masses, classical and reference load methods
  3. 14:117 min · 2 chapters

    Eigen solvers and Ritz vectors

    Compares the subspace iteration and Arnoldi-Lanczos eigen solvers, then demonstrates load-dependent Ritz vectors on a long pipe rack model. Natural modes needed 53 modes for 90% mass participation in X and 144 in Z; with Ritz vectors, 20 modes were enough.

    Chapters
    • 14:11Eigen solution methods: subspace iteration and Arnoldi-Lanczos
    • 19:40Load-dependent Ritz vectors on a pipe rack model
  4. 20:456 min · 4 chapters

    IS 1893 (Part 4): categories, Clause 10 and mass guidelines

    Introduces IS 1893 (Part 4) for industrial structures. Explains the four structure categories, which categories and seismic zones need dynamic analysis under Clause 10, and the code’s guidance on modelling rigidly and flexibly mounted equipment as lumped masses.

    Chapters
    • 20:45Seismic analysis to IS 1893 (Part 4): 2015, industrial structures
    • 21:58Structure categories 1 to 4 in IS 1893 (Part 4)
    • 22:53When dynamic analysis is required (Clause 10)
    • 24:58Additional mass modelling guidelines for equipment on structures
  5. 26:439 min · 3 chapters

    Design spectrum and response spectrum input in STAAD.Pro

    Covers site-specific versus code design spectra, then works an example: scaling an unscaled spectrum by the peak ground acceleration, and entering IS 1893 (Part 4) 2015 data in STAAD.Pro with the CQC combination, a direction factor, damping and a scale factor.

    Chapters
    • 26:43Design spectrum considerations: site-specific and code spectra
    • 28:11Scaling a site-specific spectrum to the peak ground acceleration
    • 31:30Specifying the response spectrum in STAAD.Pro: CQC, direction factor, damping, scale factor
  6. 35:274 min · 1 chapter

    Combining earthquake components

    Explains combining a full earthquake component in one direction with 30% in the orthogonal direction, or using SRSS. Shows how mass participation factors and animated mode shapes reveal asymmetry, including a torsional mode, in a model.

    Chapters
    • 35:27Combining earthquake components and spotting asymmetry from mass participation
  7. 39:365 min · 1 chapter

    Floor response spectrum

    Explains why equipment on a floor needs the floor motion rather than the ground motion as its input. Shows a time history run with the El Centro record, floor spectra generated for 2% and 5% damping, and the floor spectrum viewed in post-processing.

    Chapters
    • 39:36Floor response spectrum for equipment on a structure
  8. 44:117 min · 3 chapters

    Synthetic time history and forced vibration

    Describes converting a response spectrum into a synthetic time history, then forced vibration from running equipment. Shows a turbine foundation under time history load, where transient motion dies out into a steady state, and a frequency-domain steady state module.

    Chapters
    • 44:11Synthetic time history from a response spectrum
    • 45:29Forced vibration analysis of equipment-supporting structures
    • 47:02Steady-state results of a turbine foundation under time history load

Is the Structural Design and Analysis with STAAD.Pro (Bootcamp) course really free?

Yes. All 51 min of it is free on Skill-Lync's YouTube channel, with no payment. To watch it on this page with the chapter guide, leave your name and phone number once; you can also watch it directly on YouTube. It was published on 4 Mar 2022 and had 4,223 views as of 19 Nov 2026. This page adds the chapter guide, a study plan and what to learn next.

How long does the Structural Design and Analysis with STAAD.Pro (Bootcamp) course take to finish?

The video runs 51 min across 20 chapters. At one hour a day that is about 1 days; plan roughly twice that if you practise each exercise as you go. The longest section is "Design spectrum and response spectrum input in STAAD.Pro" (9 min), so give it its own days.

Does the free STAAD.Pro course come with a certificate?

The video description has a "claim your certificate" link, which now opens this page. To ask about a certificate for this course, leave your name and phone number in the form below and a Skill-Lync counsellor will call you back. The paid Skill-Lync courses linked here include a certificate along with mentor-reviewed projects.

What should I learn after this course?

The next step is Analysis and Design of Industrial Structures using STAAD.Pro (free lessons), then Analysis and Design of Industrial Structures using STAAD.Pro (₹40,000), then Post Graduate Program in Buildings - Engineering Design and Project management (₹2,75,000). The free course teaches the concepts; the paid Skill-Lync courses add graded projects, mentor feedback and, in the PG programs, placement support.

Do I need STAAD.Pro to follow this session?

The session is a demonstration, so you can watch without the software. The speaker shows STAAD.Pro models, the text editor and post-processing views. In this 2022 recording the speaker says the floor spectrum, synthetic time history and steady state module are in STAAD.Pro Advanced, while subspace iteration is in both versions.

Why use Ritz vectors instead of natural modes in STAAD.Pro?

On the pipe rack example, natural mode shapes needed 53 modes to reach 90% mass participation in X and 144 modes in Z, because many modes were insignificant local ones. With the Ritz vector eigen method, 90% was reached in the first 13 modes in X and the 18th in Z, over 20 modes.

Which code does the seismic part of the session follow?

IS 1893 (Part 4): 2015, the code for industrial structures. The speaker covers the four structure categories, Clause 10 on when dynamic analysis is required, and entering the code response spectrum in STAAD.Pro. Static seismic analysis is mentioned as available but not covered.

Last updated 19 Nov 2026 · Course length, chapters, views and dates from the YouTube video on 19 Nov 2026 · Grow by Skill-Lync: free lessons from every course

Finished the course?

Ask about the certificate or your next course.

Leave your name and phone number. A Skill-Lync counsellor calls you back within one working day about the certificate for Structural Design and Analysis with STAAD.Pro (Bootcamp) and the course that fits where you want to work.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Free full course · Skill-Lync

Start watching

Free, no payment. Leave your name and phone once and the whole Structural Design and Analysis with STAAD.Pro (Bootcamp) course plays here, with every free lesson on Grow. A Skill-Lync counsellor may call you about the certificate or your next course.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.