Full course · free on YouTube · 1 h 28 min

Applied engineering maths with MATLAB: free, 1 hour 28 minutes

One recorded live workshop of 1 hour 28 minutes. After a three-minute overview, the instructor explains where engineering mathematics is applied, then works two MATLAB examples: cylinder volume against crank angle, and temperature along a heat-sink fin.

7 chapters · published 17 Jan 2025 · 934 views as of 18 Nov 2026 · by Skill-Lync

Free. We ask for your name and phone once before it plays here · or watch on YouTube ↗

Who is this course for?

Engineering students who have studied calculus and differential equations but have not seen where they are used, and beginners who want a first look at MATLAB.

What will you learn?

  • Explain where first-order and second-order differential equations appear, from cabin pressure to springs, turbine blades and RLC circuits
  • Describe what a Fourier series does and why adding terms improves a synthesised waveform
  • Give reasons industry prefers computed solutions to long hand calculations
  • Write a short MATLAB script with variables, an array and a for loop, and plot the result
  • Derive piston position and cylinder volume from slider-crank geometry and plot volume against crank angle
  • Reduce the 3-D heat equation to 1-D, set boundary conditions and solve it with dsolve in MATLAB

What does each part of the course cover?

6 sections, in watching order. Click a timestamp to jump the player there. This is a recorded live session: from about 1:00:42 the recording replays the two MATLAB examples (from 0:33:30), so the last part of the video repeats.

  1. 3:075 min · 1 chapter

    What engineering mathematics is and why it is taught

    Introduces engineering mathematics as the step from school mathematics to calculus and integration, and lists what the subject covers: matrices, differential equations, complex analysis, numerical analysis, Fourier analysis, linear algebra and probability. Argues that equations should be learnt for use in industry, not only for grades.

    Chapters
    • 3:07Fundamentals of engineering mathematics
  2. 7:4410 min · 1 chapter

    First-order and second-order differential equations in practice

    Shows where simple differential equations appear: pressure change with altitude from dP = -rho g dz and the ideal gas law, compound growth of an amount, simple harmonic motion of a mass on a spring, a wind-turbine blade angle equation, and a series resistor, inductor and capacitor circuit. These are described, not solved in detail.

    Chapters
    • 7:44First-order and second-order differential equations with real examples
  3. 18:066 min · 2 chapters

    Fourier series, and why hand calculation does not scale

    Describes Fourier series as the tool for signals and waveforms, with an animation where adding more terms brings a synthesised wave closer to the target. Then explains why industry avoids long hand calculations: they take time, add human error and are tedious to repeat, which is the case for computing tools such as MATLAB.

    Chapters
    • 18:06Fourier series for signals and waveforms
    • 20:49Hand calculation versus computational tools like MATLAB
  4. 24:0610 min · 1 chapter

    Where applied mathematics is used across industries

    Walks through application areas: lift and drag on a vehicle body, chassis stress and strain, building columns and earthquake loading, aircraft structures and fluid dynamics, driverless cars, surveying, combustion, and computational fluid dynamics for HVAC ventilation and smoke flow, ending with an engine cutaway.

    Chapters
    • 24:06Where applied mathematics is used: automotive, buildings, aerospace, CFD
  5. 33:4413 min · 1 chapter

    MATLAB example: cylinder volume against crank angle

    Derives the piston position from a slider-crank geometry using the crank radius, connecting rod length and Pythagoras, then the instantaneous cylinder volume. In MATLAB it defines variables (compression ratio 9, bore, stroke, rod length), builds an angle array of 1 to 360, loops to fill a volume array and plots volume against crank angle.

    Chapters
    • 33:44MATLAB basics: cylinder volume against crank angle
  6. 46:3941 min · 1 chapter

    1-D heat transfer along a processor fin, solved with MATLAB

    Starts from the 3-D conduction equation and simplifies it (steady state, no generation, constant conductivity, variation along x only) to d2T/dx2 = 0. In MATLAB: declares y as a function of x, writes the second-order equation, sets T = 300 at x = 0 and 1000 at x = 0.1, solves with dsolve and plots a linear profile. Adding a heat term proportional to temperature then gives a curved profile. A Q&A follows.

    Chapters
    • 46:391-D heat transfer along a fin: equation, boundary conditions and dsolve, then Q&A

Is the Applied Engineering Mathematics using MATLAB course really free?

Yes. All 1 h 28 min of it is free on Skill-Lync's YouTube channel, with no payment. To watch it on this page with the chapter guide, leave your name and phone number once; you can also watch it directly on YouTube. It was published on 17 Jan 2025 and had 934 views as of 18 Nov 2026. This page adds the chapter guide, a study plan and what to learn next.

How long does the Applied Engineering Mathematics using MATLAB course take to finish?

The video runs 1 h 28 min across 7 chapters. At one hour a day that is about 2 days; plan roughly twice that if you practise each exercise as you go. The longest section is "1-D heat transfer along a processor fin, solved with MATLAB" (41 min), so give it its own days.

Does the free MATLAB course come with a certificate?

The video description has a "claim your certificate" link, which now opens this page. To ask about a certificate for this course, leave your name and phone number in the form below and a Skill-Lync counsellor will call you back. The paid Skill-Lync courses linked here include a certificate along with mentor-reviewed projects.

What should I learn after this course?

The next step is MATLAB Basics (free lessons), then MATLAB for Mechanical Engineers (₹40,000). The free course teaches the concepts; the paid Skill-Lync courses add graded projects, mentor feedback and, in the PG programs, placement support.

Do I need to know MATLAB before this course?

No. The instructor says MATLAB may be new to some viewers and introduces it in the video. He explains comments, variable initialisation, arrays and the for loop as he goes, and says the code is meant to be followed at a glance. Basic calculus and differential equations help.

Is MATLAB free to use for this course?

MATLAB is paid software from MathWorks and the video does not cover licences, so check MathWorks for a student licence or a trial. In the closing Q&A the instructor advises installing it, trying addition and multiplication first, then a simple calculator, then small differential equations.

What problems are solved in MATLAB in this video?

Two examples. First, the instantaneous cylinder volume of an engine as the crank angle goes from 1 to 360 degrees, using a for loop and a plot. Second, steady 1-D heat conduction along a fin, solved with dsolve for fixed end temperatures, then repeated with a heat-generation term.

Last updated 18 Nov 2026 · Course length, chapters, views and dates from the YouTube video on 18 Nov 2026 · Grow by Skill-Lync: free lessons from every course

Finished the course?

Ask about the certificate or your next course.

Leave your name and phone number. A Skill-Lync counsellor calls you back within one working day about the certificate for Applied Engineering Mathematics using MATLAB and the course that fits where you want to work.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Free full course · Skill-Lync

Start watching

Free, no payment. Leave your name and phone once and the whole Applied Engineering Mathematics using MATLAB course plays here, with every free lesson on Grow. A Skill-Lync counsellor may call you about the certificate or your next course.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.