Unlock all 25 lessons of Telco CloudFull course ₹40,000 · paid
From GSM to LTE: Evolved Packet Core Architecture
A free lesson from Skill-Lync's Telco Cloud course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “Week 1 Session 1”
What will you learn in this free Telco Cloud lesson?
The instructor walks through GSM and UMTS architecture, then compares LTE with them on data rate, latency and bandwidth. The lesson shows how Release 6, 7 and 8 removed nodes from the user plane to cut latency, then introduces the EPS architecture and the role of the eNodeB.
- GSM and UMTS nodes and their roles
- LTE versus UMTS data rate and latency
- How Release 7 and 8 cut user plane latency
- eNodeB functions such as admission control and scheduling
What comes after lesson 1?
The next free lesson is lesson 2, “EPC Nodes, Interfaces and Control User Plane Split” (23 min). Later in Skill-Lync's Telco Cloud course (paid): lesson 4, Week 2 Session 1; lesson 5, Week 2 Session 2; lesson 6, Week 2 Session 3. The full course has 25 lessons (12 h 32 min of video); see the course overview or its price and syllabus.
Lesson transcript
Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.
Hello and welcome to the session on Telco Cloud. Table of Contents. In this session, we will learn about the flow and evolution of LTE EPC structures, the comparison of LTE with previous technologies present, the functionality of EPS network elements, the limitations of EPC and evolution of 5G core in detail. Let us start with pre-LTE EPC architecture. Early cellular networks like GSM were initially designed for voice and circuit switch services only. The architecture of such networks was comparatively simple and comprised two main parts. The radio access network as well as the network nodes and interfaces performing core functionality like call switching, signaling, and charging.
In GSM, the radio interface was specifically designed and optimized for voice or low bit rate circuit data transmission. The circuit switch core network domain supports the circuit switch call setup, authentication, billing, and interworking with classic public switch telephone network. Second generation packet network evolved to efficiently support packet data transmission with emergence of IP and web services. The access network path was modified to support packet transmission for GPRS and edge evolutions. A new core network domain, packet switch core network, was added in parallel to circuit switch domain.
This new core network packet switch domain has similar role as circuit switch network, including authentication and billing and interworking with public and private networks. But it is for packet switch networks, but it is for packet switch data used in GPRS and edge services. It is worth noting that public switch transmission operates on a store and forward mechanism where packets are stored and forwarded in a network according to the availability of resources, whereas in circuit switch network, a circuit is reserved end-to-end for entire duration of the call.
Let us look at Global System for Mobile Communication or GSM Architecture. It comprises of Radio Access Network and Core Network. The Mobile Station or the MS comprises Mobile Equipment and SIM Card, Subscriber Identity Module. This is a user device that interacts with the Radio Access Network. The RAN has three nodes, Base Trust Receiver Station, Base Station Controller, and Transmission Rate Adaptation Unit. Both BSC and BTS nodes work together to maintain the entire radio network and provides radio frequency connectivity between the mobile station and the core network.
Transmission Rate Adaptation Unit does the rate conversion from 64 kbps to 16 kbps or from 16 kbps to 64 kbps. As mentioned earlier, the core network can be divided into two parts, circuit switch core network and packet switch core network. The Master Switching Center or MSC is the main node that manages the signaling for call setup, thus call supervision and call termination. It also performs user plane management for voice call. Whereas, Gateway MSC or GMSE work as a gateway to connect calls in and out of the network.
Other nodes like Visitor Location Register keeps the record of user's location and registration in the network. The Home Location Register maintains the subscriber database in the network permanently. The Equipment Identity Register keeps track of equipment used in the network. The Authentication Center is used to provide authentication parameter to VLR via HLR to authenticate and authorize the mobile equipment. In Packet Switched Network, the Serving GPRA Support Node or SGSN does packet routing and transfer. Mobility Management that is attach, detach and location management for the UE, logical link management and authentication along with charging functions.
The Gateway GPRA Support Node or GGSN does the IP address allocation to the UE and it also performs the charging function similar to SGSN. GGSN is the breakout point for the user to connect to the external packet data network. As you might have noticed already, Universal Mobile Telecommunication Services or UMTS architecture is similar to GSM. Interestingly, the base transfer receiver station is replaced by node B and the base station controller is replaced by RNC. UMTS uses core division multiple access technology over the air interface instead of frequency and time division multiple access used in GSM.
Core network is also similar except for the fact that now instead of a single node master switching center that handles both signaling and voice circuits for voice calls, a single MSS node can manage control plane for many MGWs. For example, there are two separate entities, MSC server and Multimedia Gateway . This functionality enables split control, signaling handled by the MSS and user plane handled by the MGW. That guarantees better placement of the network element within the network. A single MSS node can manage control plane for many MGWs and can be centrally placed.
There is no significant change in the packet switch network for UMTS architecture. Now, let us discuss about evolution of LTE and comparison with previous technologies. Many drivers pose the need for new technology. First, the advancement of wired broadband technology that pushes for higher data rates to compete wireless technology with the wired technology. In case wireless technology is not capable enough, then mobile operators will lose their revenues to the broadband service providers. Since the packet network came into existence, the consumption of packet data rate has been increasing day by day.
More data is transferred on UMTS network than it was transferred on the GSM. Near technology naturally is expected to bring more traffic, hence new technology must have more capacity. The presence and improvement of other wireless technology like WiMAX make environment competitive and hence elevate the expectation of customers to have better experience from newer wireless technology. Just like wireline broadband provides flat charging, new technology must also be cost effective and cheap enough to be able to use by everyone. Long term evolution is truly global roaming technology as LTE can interwork with all previous technologies, whether 3GPP or non-3GPP.
WCDMA or UMTS can only work with GSM but not with CDMA 2000, whereas LTE can interwork with UMTS, GSM and CDMA 2000. It provides much higher downlink and uplink data rates. LTE offers downlink data rates in order of hundreds of megabits per second, whereas UMTS could offer only up to 14 Mbps per second in downlink without MIMO. UMTS also improves user experience with its proper responsiveness. This is possible due to very low user plane latency. The user plane latency can be understood as the lowest time required for transferring a PDU across the physical layer.
In LTE, this user plane latency is in range of 10 to 20 ms, whereas in UMTS or HSPA, it was much higher, 18 ms and 15 ms respectively, approximately. To make LTE EPC easily deployable, LTE has deployed using different bandwidth sizes, 1.4 MHz, 3 MHz, 5 MHz, 10 MHz, 15 and 20 MHz. This allows operator to deploy LTE using LTE. It uses narrower bandwidth if entire 20 MHz band is not available. To make LTE an affordable technology, it uses Orthogonal Frequency Division Multiplexing or OFDM over-air interface and IP-based interfaces for connectivity between different network elements.
On the other hand, UMTS used proprietary Code Division Multiple Access technology. To understand the EPS architecture and evolution of EPS architecture, let us first understand the 3GPP Release 6 architecture. This shows path for user plane which is represented by solid line and control plane represented by dotted line. Now in Release 6 architecture, both user plane and control plane has to pass through Node-B, RNC, SGSN and GGSN to reach to the external server. This adds to control plane and user plane latency. Since in LTE we are targeting low user plane latency, that is less than 10 ms, in Release 7, SGSN is moved out of the path of user plane.
The data paths are transferred directly from RNC to GGSN and GGSN to RNC in uplink and downlink respectively. This reduces the number of nodes in user plane transfer and help reducing the user plane latency. Note that SGSN is still managing the control plane for packet data users managing their session. To further reduce the latency, another possible configuration is to merge both RAN nodes, that is Node-B and RNC in a single unit. As a result, now for user plane transfer, there are only one RAN node and GGSN between the UE and the external server.
This architecture inspires the architecture of 3GPP Release 8 that introduces Evolve Packet Core. You can compare the two diagrams on the right hand side, Release 7 and Release 8. They are exactly same, except the name of the nodes have been changed. We will learn about the Evolve Packet Core architecture in detail in the later half. But at this point, it is important to understand that how reducing the number of nodes in user plane path between the user and the external server facilitates in reducing the user plane latency down to 10 milliseconds.
LTE Highlights Long-term evolution, LTE is the successor not only of UMTS but also of CDMA2000 technology. By 3GPP2. The Evolve Packet System is made up of Evolve Packet Core network and EUT-RAN LTE. LTE networks are designed to provide high data throughputs to the users. LTE targets to provide very low user plane latency, approximately in range of 10 milliseconds. LTE has no circuit switch connectivity. It has only packet switch connectivity. Now, let us discuss about Evolve Packet System network architecture. The Evolve Packet System or EPS is made up of Evolve Packet Core and Radio Network referred as Long-Term Evolution or EUT-RAN. As we just learned, Radio Network of LTE is inspired from UT-RAN and hence New Radio Network is referred as Evolve UT-RAN.
Please note that in EPC, there are no circuit switch nodes like MSS or Media Gateway. This is because EPS is introduced to provide high-speed broadband wireless connectivity to the users. Even the real-time services as voice call, video calls are realized over high-speed packet switch network. The data rate provided by EPC network is very high and the latency so low that even the packetized real-time services appear to be continuous just like legacy circuit switch network. Now, let us discuss the architecture of Evolve Packet System. The architecture of EPS is quite different from UMTS or GSM.
UMTS or GSM had a tree-like architecture. However, EPS architecture is much flatter. There is no circuit switch node. Only packet switch nodes are present. The user plane connectivity is quite simple. It goes from external packet data network to the PDN gateway or packet data network gateway, from PGW to serving gateway or S gateway and from S gateway to the E0B. E0B then deliver those user plane packets to the user equipment or UE. However, for control plane, the E0B is connected to mobility management entity or MME.
This entity is responsible to manage the mobility of the user equipment in and out of the network. When the UE is switched on, it registers into the network via MME. MME is connected to Home Subscriber Server or HSS which is similar to HLR in GSM and it stores subscriber information permanently. MME is also connected to serving gateway because when the user sends a service request, MME instruct S gateway to establish a path or bearer from PDN gateway till E0B. S gateway is connected to PDN gateway to exchange control plane and transfer the user plane packets from external PDN towards the radio access network.
PDN gateway, before providing the path or the bearer for service will check the policy charging rule function or PCRF to check for network charging policies to be applied according to which it provides services to the user. Due to the flat IP based architecture and reduction of the number of nodes in the user plane, as you can see on the slide, the user plane latency is greatly reduced. We will discuss about each node functionality individually and each interface in more detail going forward. Now we will discuss about EPS network elements and functionalities.
Let us start with E-Node B or Evolve Node B. As the only node present in the radio access network, E-Node B is the entity that is entirely responsible for managing the radio resources. It manages the mobility of the users in the connected state, load balancing between the cells. E-Node B broadcasts cell parameter or cell information all the time that UE receives and used to learn about the cell and its parameter. E-Node B is responsible for radio bearer control. It set up signaling radio bearer and data radio bearer supervises them and terminates them when they are no longer required towards the UE.
When a UE tries to latch onto the cell or attempts to access the service, E-Node B perform the admission control to check if it has capacity to admit user and new bearers. Allocation of resources to the UE in the downlink and uplink is also performed by the E-Node B. Allocation of resources to UE in downlink and uplink is also performed by E-Node B. This is performed every millisecond in LTE and is referred as scheduling interval. When UE transmits, E-Node B is the receiver. Apart from receiving data and forwarding it to serving gateway, E-Node B also perform uplink channel quality measurements to assess the uplink radio quality of the UE.
Being placed between the core and the user equipment, E-Node B routes the user data from the serving gateway to the UE and from UE to the serving gateway. Generally, E-Node B is connected to multiple MMEs for redundancy. The selection of MMEs for the UE during the attach procedure is also performed by the E-Node B. The selection of MMEs for the main course is selected for the UE. E-Node B.