3D Finishing Challenge
AIM:
- Perform 3D finish for all units of Assembly design.
- Create Rough locators for Assembly.
3D FINISH:
The 3D finish is the process where design is completely finishing & to be ready for final simulation & 2D detailing
- In 3D finishing we perform and ensure the following points:
- Hole concentricity & hole sizes- All parts Hole concentricity is checked & confirmed while finishing the parts.
- Machining Area- The machining area in every part is defined & the machining area is highlighted by using orange colour.
- Nominality- All units dimensions are maintained nominal to facilitate easy assembly of the unit.
- Holes colouring standard- Color Code standard used in the 3D finishing
- Violet - Simple Hole
- Yellow - Threaded Hole
- Cream - Machined area
- cyan - Dowel pin Hole
- Fasteners implementation- Fasteners are implemented in all unit as per the requirement & load on the part.
- Avoiding clash between different part- Proper gap is maintained between parts to avoid the clash.
- Mylar splitting as per panel profile- Mylar splitting are confirmed while finishing the design.
- Proper renaming of parts/assemblies as per standard-proper renaming of parts & assemblies are done while finishing the design hence we can identify each & every part easily with a unique identification.
1 Renaming and Structuring of the design tree:
- Renaming of the design tree is done. and structuring design tree in way that its simple to identify the units. some units use multiple time those are easy to identify by its name.
2 Base Unit:
- Renaming of parts and structuring design tree
| Checking Parameter | Action |
| Rename of the design tree | Done |
| Mark Machining Area | Done |
| Nominality | Done |
| Holes colouring standard | Done |
3 Retractable pin unit
- Holes are make to the nominal and Concentric to each other.
- the open position of retractable pin is shown in yellow colour
- The proper butting of the two parts is done.
- colour coding is done as per the standards.
- structuring design tree renaming of parts is done.
- below are some images after 3d finishing done on fixed pin unit.
| Checking Parameter | Action |
| Rename of the design tree | Done |
| Mark Machining Area | Done |
| Nominality and Concentricity | Done |
| Holes colouring standard | Done |
4 Swivel Clamp Unit
- Holes are make to the nominal and Concentric to each other.
- The proper butting of the two parts is done.
- fasteners are implemented.
- colour coding is done as per the standards.
- structuring design tree renaming of parts is done.
- mylar splitting is done.
- the open position is shown in yellow colour.
- below are some images after 3d finishing done on swivel Clamp unit.
PROJ07_Z07_ST07_01_00_CLAMP_UNIT[2X] - A Symetric 3D Model is designed along with this
| Checking Parameter | Action |
| Rename of the design tree | Done |
| Mark Machining Area | Done |
| Nominality | Done |
| Holes colouring standard | Done |
PROJ07_Z07_ST07_03_00_CLAMP_UNIT[2X] - A Symetric 3D Model is designed along with this
| Checking Parameter | Action |
| Rename of the design tree | Done |
| Mark Machining Area | Done |
| Nominality | Done |
| Holes colouring standard | Done |
PROJ07_Z07_ST07_05_00_CLAMP_UNIT
| Checking Parameter | Action |
| Rename of the design tree | Done |
| Mark Machining Area | Done |
| Nominality | Done |
| Holes colouring standard | Done |
PROJ07_Z07_ST07_06_00_CLAMP_UNIT
| Checking Parameter | Action |
| Rename of the design tree | Done |
| Mark Machining Area | Done |
| Nominality | Done |
| Holes colouring standard | Done |
ROUGH LOCATORS
| Checking Parameter | Action |
| Rename of the design tree | Done |
| Mark Machining Area | Done |
| Nominality | Done |
| Holes colouring standard | Done |
A FULL IMAGE OF PANEL