Week 7 Challenge - Assembly Workbench
sir in challenge 5 I have submitted wrong file. please check For that challenge, I have attached the same assembly file by mistake. please check
Abhijit Mhetre
updated on 05 Sep 2023
Project Details
Leave a comment
Thanks for choosing to leave a comment. Please keep in mind that all the comments are moderated as per our comment policy, and your email will not be published for privacy reasons. Please leave a personal & meaningful conversation.
Other comments...
Be the first to add a comment
Read more Projects by Abhijit Mhetre (22)
Photo Realistic Rendering
https://drive.google.com/file/d/1KgCRxqafOFeswANMuqwKXPWD_74ps7N7/view?usp=drive_link MODELING OF AMERICAN CHOPPER IN SOLIDWORKS Objectives- The main objectives of this project are: To create individual parts of chopper using solidworks To assemble all the individual parts into chopper…
11 Feb 2024 10:32 AM IST
Design of backdoor
https://drive.google.com/drive/folders/14SPCLEEhI21bM0ubGl3Jgrx8eRx_9Wsp?usp=drive_link Project completed.
06 Feb 2024 04:32 AM IST
Project 2
complete project.
27 Jan 2024 11:11 AM IST
Project 1
completed project
27 Jan 2024 10:53 AM IST
Wiring harness design in CATIA V5 - 3D modeling Week 7 Challenge
AIM: TO FLATTEN THE WIRING HARNESS AND DRAFT THE WIRING HARNESS ASSEMBLY. GIVEN: HARNESS ASSEMBLY: HARNESS FLATTENING: WE GO TO THE HARNESS FLATTENING WORKBENCH AND DEFINE THE FLATTENING PARAMETERS. WE USE THE EXTRACT COMMAND TO BRING THE HARNESS ASSEMBLY TO THE FLATTENING WORKBENCH HERE. CHOOSING A SUITABLE PLANE WE FLATTEN…
26 Jan 2024 06:07 AM IST
Wiring harness design in CATIA V5 - 3D modeling Week 5 & 6 Challenge
Check the bundle Continuity. Add snap of result in submission Add annotation to all connectors. Make an assumptions for annotations like connect 1 , 2 etc Generate CAT.part of harness assembly and convert is in. igs format.
25 Jan 2024 01:27 PM IST
Wiring harness design in CATIA V5 - 3D modeling Week 4 Challenge
Aim: 1) To Route the following harness layout in the Electrical workbench. 2) Add protective covering on all branches connected to DT06-2S & DT06-4S connectors. Given: CAD data of the following Connectors: DT06-4S DT06-6S DT06-2S DT06-08SA Connectors Layout Design: Steps to be followed: 1. Download…
06 Jan 2024 07:21 AM IST
Wiring harness routing & packaging Rules Week 3 Challenge
AIM: To solve the above assignment questions and define the necessary electrical properties in the respective workbench. OBJECTIVE: To download the P-Clamp CAD data and define it as Electrical Support in the Electrical Part design workbench and also define the necessary electrical properties.…
04 Jan 2024 05:59 PM IST
Wiring harness design in CATIA V5 - 3D modeling Week 2 Challenge
completed
03 Jan 2024 02:33 PM IST
Fender Design
completed.
30 Dec 2023 04:26 PM IST
Roof Design
complted.
30 Dec 2023 04:24 PM IST
Section Modulus calculation and optimization
Section Modulus Calculation Of Hood Aim To calculate the section modulus of the previously designed hood for analyzing its strength and also optimizing the design to see the difference in the bending strength of the hood. Higher the section modulus of a structure, the more the resistive it becomes to bending.…
01 Dec 2023 04:07 PM IST
Hood design-Week 2
Hood Design in UG NX If fig not show I have attached in zip file. Objective Design hood outer panel, inner panel and reinforcements with the given outer hood skin, master section and design parameters. Introduction The hood or bonnet is the hinged cover over the engine of motor vehicles. Hoods can open to allow…
01 Dec 2023 01:47 PM IST
Week 12- Final project
completed
28 Sep 2023 01:30 PM IST
Week 11 - Project - A pillar Design with Master Section
A-PILLAR DESIGN WITH MASTER SECTION AIM: To create the A Pillar Design with the master section given as the intersection sketch with the Class A surface and create the tooling axis and perform the Draft analysis for the final solid part. CLASS A SURFACE: Class A is an aesthetic surface with the highest quality…
28 Sep 2023 12:44 PM IST
Week 10 - Challenge 3 - Door Trim Lower with Engineering Features
completed
26 Sep 2023 02:03 PM IST
Week 10 - Challenge 1- Attachment Feature Creation (Ribs & Screw Boss)
completed
26 Sep 2023 01:27 PM IST
Week 10 - Challenge 2- Attachment Feature Creation (Dog House)
completed
26 Sep 2023 01:21 PM IST
Week 9 - Challenge 3 - Bumper
completed
23 Sep 2023 01:21 PM IST
Week 9 - Challenge 2 - Switch Bezel Design
completed
17 Sep 2023 02:18 PM IST
Week 9 - Challenge 1 - Base Bracket Design
completed
17 Sep 2023 02:13 PM IST
Week 7 Challenge - Assembly Workbench
sir in challenge 5 I have submitted wrong file. please check For that challenge, I have attached the same assembly file by mistake. please check
05 Sep 2023 12:16 PM IST