Design of rear wheel and front fork of an assembly Chopper

AIM The Main objective of this project is to extract the different co-efficients of the species and calculate the enthalpy, entropy and specific heat of the given NASA THERMODYNAMIC DATA and calculate the molecular weight for all species in the given data file. PARSING Parsing is the process of Analysing a string of symbols,…

GENETIC ALGORITHM Genetic Algorithm are intelligent search techniques maintaining a population of candidate solutions for a given problem and search the solution space by applying variation operator. They refer to a family of computational models inspired by darwin\'s theory of biological evolution. This idea of natural…

SIMULATION OF SIMPLE PENDULUM USING ODEs The main objective of this challenge is to write a program to simulate the motion of simple pendulum using ordinary differential equations. In Mathematics ordinary differential equation is an equation containing one or more functions of an independent variables and the derivatives…

BACKDOOR  The design of backdoor was completed with all the necessary reinforcements with the help of tutorials provided. https://drive.google.com/open?id=1f4wyHorTw5mrwx63RyJHqqkpaL5YGd1D  

ROOF  The conventional task of a roof panel is to sit above the car, protecting the passengers from sun, wind and rain. It is attached to front and back rail. Design of roof includes somr reiforcements which give strength to the roof in case of heat and snow load condition. They are  Front Roof rail Bow Roof…

SECTION MODULUS It is geometric property mostly used in design of beams or any other flexual members. It highly depends on the shape of the body. It is defined as the ratio of moment of inertia of section about its centroidal axis to the extreme layer of neutral axis.               …

HOOD DESIGN   Intorduction The hood is an opening body panel that covers the engine in a front engine vehicle. The hod is also considered as another type of door in a vehicle as it consists of upper front panel and inner panel. This hood decimitates the force from entering into the body. It is made aerodynamic in…

FENDER Fender is a panel that are next to the hood on the either side of the car that covers front wheel.This prevents spraying of sand, mud, rocks and liquids into the air by the rotating tyreMore elaborate design include fender skirts for enclosing the outside edge of the wheel well They are 5 mounting points in fender.…

EUROPEAN STANDARD FOR WHEEL ARC   CRITERIA TO PASS THE EUROPEAN STANDARDS The above sketch was created based on the standards of european regulations. To pass the test all the lines should have a minimum clearence of 5mm when viewed from top. Let us check now for all the lines  LINE 1 The above image shows a…

PHOTOREALISTIC RENDERING  In 3-D  design, photorealistic rendering is the process of add shading, color and lamination to a 2-D or 3-D wireframe in order to create life-like images on a screen. The rendering process plays a crucial role in the computer graphics development cycle. Below is the procedure followed…

CASING DESIGN SOFTWARE USED: NX CAD PROCEDURE Create a Tab with 1mm  thickness and and use the cutout botton option to remove the left side of the tab of 5mm wide and 40mm long. At 10mm distance from the edges bend the tab inside Add Flanges to the corners and break the corners of the flanges by using break corner…

 BOX ASSEMBLY SOFTWARE USED: NX CAD   PROCEDURE Create a base and then use flanges on two ends normal to xy plane using the dimensions given and then make flangs on right ends of the part normal to xz. Use close corners to cover the gaps between between the flanges and base  Close the gap between flanges…

ASSEMBLY OF SUNSEEKER PREDATOR YACHT USING SOLIDWORKS  https://drive.google.com/open?id=1KXFShWG2FLqLHRHZDgBYTuii5mEh_7mf INTRODUCTION Running or resting at the dock, the Sunseeker predator yacht  breaths motion and exudes action. With racy Italian-style lines, it is a greyhound poised to charge off the starting…

1) CHASIS: procedure: 1)open a new part with model units set to millimetres 2)open the sketch picture and fix it to the origin as per the requirement  3)select the top plane and draw a sketch as shown in the figure and close the sketch   4)select the midplane chasis and draw a sketch as shown in the figure…

procedure: 1)open a new part with model units set to millimetres  2)Select the front plane and create a sketch by clicking on the 2d sketch icon 3)Draw a midpoint line of length 300mm and width 45mm and draw another sketch attached to it as shown in the figure  4)Then revolve the sketch taking 110mm line as reference…

BENCHMARKING As per the requirements of pughazhyendii i made a list of  cars to suit for his budget. They are 1)Hyundai venue E 1.4 CRDi the specifications of hyundai venue E 1.4CRDi are as follows    and it also comes with bs6 version    2) TATA Nexon XE Diesel the specifications of tata nexon…

FRONT WHEEL: procedure: 1)open a new part with model units set to millimetres  2)Select the front plane and create a sketch by clicking on the 2d sketch icon 3)Draw a midpoint line of length 110mm and width 40mm and draw another sketch attached to it as shown in the figure  4)Then revolve the sketch taking 110mm…

1) Transmission belt:   procedure: 1)open a new part with model units set to millimetres  2)select the front plane and create a sketch by clicking on the 2d sketch icon  3)click on the line on the left corner of the screen and draw a line from the origin towards right with a length of 350 mm  4)Draw…

1)Oil Tank: procedure: 1)open a new part with model units set to millimetres  2)Select the top plane and create a sketch by clicking on the 2d sketch icon 3)Draw a vertical midpoint line from the origin at a distance of 50mm, then draw a       horizontal construction line to the right at a distance…

Every day we see a large number of cars moving on the road, especially on Indian roads there are thousands of pieces of stones on the road, and they are constantly hitting your car on the underbody, wheel arches, sills, and the trunk lower part while driving on the road. In some cases, the underbody might be scratched…

1)GAS TANK: procedure: 1)open a new part with model units set to millimetres 2)open the sketch picture and fix it to the origin as per the requirement  3)Select midplane  and click on the 2d sketch icon  4)Draw the sketch as shown in figure below  5)Draw the sketch as shown in figure below  6)Use…