Creating Bar Bending schedule, Different Door types, and Creation of standard drawing templates using AutoCad

1. Create the templates as shown in Figures. Take the size of the title block as per industry standards or
you can assume it as per the size of the paper. Use text and attributes wherever required. After creating
the title block you need to save it as a block with names: Custom1_titleblock and Custom2_titleblock,
respectively.

AIM:

To Create Custom1_titleblock and Custom2_titleblock using Attributes and block command from Autocad software .

PROCEDURE:

Step 1 ( custom1_tittleblock)

• In the command prompt type L to draw the lines
• In ribbon tab > Annotate > Mtline ( to draft the text )
• go to properties tab to change the colour

• In the riibon bar >block > create block and name it Custom1_titleblock.Therefore the block is created

STEP 2 (custom2_tittleblock)

• In the command prompt type L to draw the lines
• In ribbon tab > Annotate > Mtline ( to draft the text )
• go to properties tab to change the colour
• In the riibon bar >block > create block and name it Custom2_titleblock.Therefore the block is created .

2. Create the doors type for warehouse as shown in the Figure. You need to create each door type as per
standard size or given dimensions. Create the blocks of this door type after creating them.

AIM:

To create the doors type for warehouse and to also create the block of this door type after creating them using AutoCAD

PROCEDURE:

step 1:

• In the command prompt type the units > mm
• In the command prompt type the limax > 100,100
• In the command prompt type the limits >0,0

step 2 :

• In the command prompt type l to draft the lines
• In the command promt type rec to draft the boxes or rectangle
• In the command prompt type fillet to get the curve edges
• In the ribbon bar > dimensions ( to give the dimensions of the door )
• In the ribbon bar > annotation > text ( to give the text for the door )
• In the ribbon bar >block >create block ( to create the door block

step 3 :

• In the command prompt type l to draft the lines
• In the command promt type rec to draft the boxes or rectangle
• In the command prompt type fillet to get the curve edges
• In the ribbon bar > dimensions ( to give the dimensions of the door )
• In the ribbon bar > annotation > text ( to give the text for the door
• In the ribbon bar >block >create block ( to create the door block )

3. Create each symbol as a block with the name given in the legend. After creating the blocks arrange
them in the legend as shown in the Figure.

AIM:

To create each symbol as a block with the name and then arrange them in the legend

PROCUDER:

• In the command prompt type C to get the circle
• In the command prompt type L to get the lines
• In the ribbon bar > annotation> Multiline text
• In the ribbon bar >block >block edit
• same commands and procedure are followed for all the symbols
• • In the command prompt type l to draw the lines
  • In the command prompt type arc to draw the arc
  • In the command prompt type Mtext
  • In the ribbon bar > block>create block
  • In the command prompt type l to draw the lines
  • In the command prompt type Mtext
  • In the ribbon bar > block>create block
  • n the command prompt type l to draw the lines
  • In the command prompt type fillet to get the curves
  • In the command prompt type Mtext
  • In the ribbon bar > block>create block
    • In the coomant prompt type I to insert the blocks

    • FINAL RESULT :

• 4. Create the door type for residential building as a block. Save the name of the blocks as type. Use given
  dimensions or assume dimensions as per industry standards.

  AIM:

  To Create the door type for residential building as a block .

  PROCEDURE:

  step 1:

  • In the command prompt type units > engineering >inches
  • In the command prompt type limits>0,0 , limax >100,100
  • In the command prompt type zoom > a

  step 2:

  • In the command prompt type l to draw the lines
  • In the command prompt type B to create a block ]

5. Create each shape as a block as shown in the Figure. Save the block and insert them on the table as
shown in the Figure.

AIM:

To Create each shape as ablock and insert them on the table as given in the picture

PROCEDURE:

step 1:

• In the command prompt type Unit>decimal>meters
• In the command prompt type limits>0,0
• In the command prompt type limax >100,100

step 2:

• In the command prompt type l to draw the desired lines
• In the command prompt type pl to draw the desired arc,poly lines
• In the command prompt type mt to give annotation and text
• In the command promt type B to create the block
• In the command promt type I to insert the created in the block
• In the command prompt type table to inset the table