Creating a Layout, Section and Elevation with dimensions using AutoCad

Design & Analysis Of A Hostel Building At Guwahati Assam Aim : To design and analyze of G+3 (RCC) Hostel building in ETABS and Foundation in CSI SAFE. Introduction :-  The procedure for analysis and design of a given building will depend on the type of building its complexity, the number of stories, etc. First, the architectural…

1A)   AIM:-  To model the isolated footing by using  SAFE and to analyze and to design it to verify the size, depth and calculation of steel provided INTRODUCTION:- All the steps are going to be mentioned along with step by step procedure. PROCEDURE:- Open SAFE software Create a new model Edit the settings …

Column Size = 400 x400 The compression axial load for the load combination of (1.5 DL + 1.5 LL) is 2000 KN The safe soil bearing capacity is 150 KN/m2 at Foundation depth below E.G.L = 2metres Grade of concrete for footing = M25 Footing Size column load 2000KN 10% of footing self weight = 2000x10/100 = 200KN Axial load…

Introduction :-   Etabs :- ETABS is one of the most powerful software tools for structural analysis. 3D modeling, visualization, and automatic code-based learning are some of the unique features of this software. ETABS also supports several analytical models like response spectrum analysis, time-history analysis,…

Aim : - To Extract values of longitudinal steel ratio, boundary element length and shear reinforcing ratio from the design results. - To tProvide cross sectional steel arrangement of the shear wall from its base up to terrace. - Using AutoCAD application for this exercise or Alternatively, it can be drawn by hand as well.…

1A) AIM: To run the analysis and design the RCC moment-resisting frame of the given ETABS file and to provide details of longitudinal reinforcement for the two columns (3A and 3B) from foundation level to terrace level. To sketch the column cross-sectional & elevation details or draft it using AutoCAD software. To…

1A) Aim:- To carryout the analysis of the given Etabs model and to design the RCC moment resisting frame. To provide the detailing of longitudinal and shear reinforcement for two continuous beams. To provide the reasons of failure of middle span along grid A. Introduction:- In this challenge two beam detailing is done: …

1A) Factors influencing the dynamic characteristics of a building :- -  Buildings oscillate during earthquake shaking. The oscillation causes inertia force to be induced in the building. - The intensity and duration of oscillation, and the amount of inertia force induced in a building depend on features of buildings,…

1A) AIM: To model a 25 storey building on ETABS with structural properties as specified below. Ground floor or plinth floor level can be taken at a height of 1.5 metres from the base. Each of the successive 25 storeys has a storey height of 3 metres. Structural Element Sizes  Beams : 300 × 400 mm …

1A) CASE A) Restraint of floor shrinkage  obesrvation full restraint at all corner  conclusion option a will have higher restraint to shrinkage thus lead to crack in the floor, option B is average option C will not effectively restraint the srinkage so possibly less cracks    The lateral stiffness  obesrvation comparatively…

1A) Symmertry: It is observed that the distribution of mass,stiffness is across the plan has good symmetrical aspects. This tends to reduce the horizontal displacements in both of the two horizontal displacements in both of the two Orthogonal Horizontal Directions. It also has a very good uniformity also. Redundancy: …

1A)   Mass matrix m = Modified mass matrix  Model property  Ln            For the first mode    n=1 Modified mass matrix M1 =   m1=3.861m   Model property  L1 = L1=4.121m Model participation factor           Γ1=L1/M1              =4.121m/3.861m              =1.067   Effective modal mass                     M1* =(4.121m)^2/3.861m…

1A)                   STATIC ANALYSIS                   DYNAMIC ANALYSIS       1. Load is not variable with time and neglected due            to slow applying of load.      1. Load is variable with time due to fast                    applying of load and vibration.        2. Motion of the structure can be disregarded. …

  1) a)              This crack will be formed due to the flexural failure of a beam. The flexural strength, known as modulus of rupture, bend strength, or fracture strength, is a material property, defined as the stress in a material just before it yields in a flexure test. The flexural strength represents the highest…

1A) AIM: To use the architecture/ structure project file  to export revit architecture and structural model to Naviswork cache file TOOLS USED: FILE EXPORT NWC PROCEDURE: open an architectural model created in week 8 click on 3D view go to file click on export and save as NWC repeat it for both architctural and structural …

1A) AIM :   To create a seet of sinusoidal points and create a curve and create a surface out of the curve. TOOLS USED : Dynamo. Code block. Range. Mat.sin. Integer slider. Product (*). Add (+). Points by coordinate. List. Surface by loft. PROCEDURE : 1. First open a new revit file and open a architectural template. 2.…

1A) AIM: Using the shortcut key to complete the given task INTRODUCTION: In this question we have modify the existing project by using shortcut key. One by one shown the step PROCEDURE: A) SECTION BOX (BX) Open Revit software Click on open and select previously created model Set in 3D view Select any part of the building…

1A)The abbrevation HVAC stands for heating,ventilation airconditioning.The main purpose of this building is that it provides heating and cooling to few kinds of buildings.It uses freesh air from the outdoors to provide hih indoor air quality which is very healthy.The process of replacing or exchnaging air within a space…

1A) ANSWER:  My model represents a Multi Unit Residential Apartment .  2A)  My assumed location details are T-nagar , chennai -600017 my modeling gives the model requirements from NBC 3A)   AIM: To create foundation  , columns , beams connected to columns , roof framing , floor , floor openings for elevators and stairs…

1A) Aim: to set project base point and project shared coordinates for the project. Procedure: To create project shared coordinates: Open architectural tab Open Manage tab. Click on project coordinates and then specific shared coordinates. In north/south type 0'0". In east/west type 0'0" To create project base points: Select…

1A)  BUILDING CODES of standard modelling.      A model building code organisation is a set of building codes that are developed and maintained by a standard organisation.  This standard organisation operates indenpently of the jurisdiction or area in which the building code standards are being…

1A)  AIM: Created a ceiling in the first floor level  INTRODUCTION: From the architectural tab to model a ceiling at the first floor level on the saved week 3 project of the residential unit. PROCEDURE: STEP 1) OPEN MODEL Launch the Revit software Click on open and select previously created drawing  STEP…

1.Ans:- BIM is a new process and methodology by which a team of architects, engineers and contractors work collaboratively to design and build a commercial building utilizing the same database and computer model. This allows the team to analyze and visualize design decisions long before a project even breaks ground, at…

1) Aim :- Open the file menu, create a new project (Structural / Architectural / Construction template ) and name the project appropriately. Procedure :-               * Open the revit software.               * Next we select model-new project.               * Template file select as Architectural template.            …

AIM: To create a 3 dimensional model of the residential building  To create a rendered view of the developed model. To use materials and light setting. Procedure: Here in the project we are going to create a 3d model of a residential building. This is building after being created, it is rendered. The rendering of the model…

1A)   AIM:- To create a 3D isometric view of the given building with plan and elevation.    INTRODUCTION:-  An isometric drawing is a 3D representation of an object, room, building or design on a 2D surface. One of the defining characteristics of an isometric drawing,…

1A)   AIM: To create a 3D Furniture element as shown in the Figure. Assume dimensions which are missing. PROCEDURE: Using Worskspace switching icon 3D Basics workspace is set. Using LINE tool the outline is formed. Inside the outline a rectangle is created using RECTANGULAR command. Using BOUNDARY a surface is created…

1A)   Aim :- To create a layout of the plan and sectionusing template tutorial-mArch.dwt. To create a viewports by edit attributes in templates and taking a plot. Procedure :-  First, Go to LAYOUT command and Select new layout and rename it as PLan and Section. And Delete the current Viewport. Type LAYOUT command and select…

1A)   Aim: To Create the Kitchen Layout and to Also, use proper dimension techniques to dimension the kitchen layout. Also, insert text wherever required. All dimensions are in mm. Procedure: step 1: units are set to mm limits and limax are also set zoom comand is also used Steps for drawing Below Counter Plan Open Auto…

1A) Aim: To create the templates Custom1_titleblock and Custom2_titleblock as shown in the figure Introduction: The tittle block is a template created in a sheet which contains the information or data regarding the drawing and also the information of the company and persons of the company responsible for the…

AIM :           TO DRAW RESIDENTIAL BUILDING OF DIMESIONS 60' X 20'  WITH THE FOLLOWING DRAWINGS 1) ARCHITECTURAL DRAWINGPLOT DRAWINGGROUND FLOOR PLANFIRST FLOOR PLANELEVATION VIEW 2) STRUCTURAL DRAWINGSECTION VIEWFOOTIG LAYOUTCOLUMN LAYOUTBEAM LAYOUT INTRODUCTION : THE RESIDENTIAL BUILDING TO BE DRAWN WITH PLOT DIMENSIONS…

Aim:- To draw the floor plans and sections using the proper dimension techniques and dimension styles to document the project. Introduction:- • Plan and Sections are different types of drawings used by architects to graphically represent a building design and construction.• A plan drawing is a drawing on a horizontal plane…

Ans.1. Draw the elevation and details of a wardrobe as shown in the Figure below. After sketching, you need to provide the dimensions and text with the use of layers. Use proper text styles and dimension methods to document it. Also, assume dimensions, wherever needed. Note: All dimensions are in mm. Aim               …

AIM :  1. Create a column schedule as shown in the figure. Note: Create a column schedule with the help of lines. Also, insert text with the help of Dtext command or Single Line text. Hint: Use font name: romans.shx; Height: 8”, Justify: Left 2. Create a window schedule as shown in the figures: 3. Create the drawing template…

1A)  AIM:Sketch of the residence layout with help of the autocad essentials I. In command prompt type (startup:1)II. Then file>newIII. Then create new drawing window select metric in default settingsIV. In advanced setup in units check on the architectural, angle in degrees, then okV. In command prompt type (xl enter h…

AIM: To draw the geometries using Chamfer, fillet tool in Autocad. Commands used: Line, circle, chamfer, fillet, mirror, trim, move, rotate, annotate. Procedure:  1.New sheet- units- decimal-precision 0.00- meter-ok. 2.Limits- 0,0 and 420,210. 3. zoom-All. 4. Select Line tool and draw the lengths starting from base of…

AIM- 1- TO DRAW THE CROSS SECTION OF LOAD BEARING WALL OVER SPREAD FOOTING      2- TO DRAW THE CROSS SECTION OF ISOLATED FOOTING. 3- TO DRAW LINE DIAGRAM OF TWO BEDROOM BUILDING. 4- TO DRAW CROSS SECTION OF A LOAD BEARING WALL SHOWING FOUNDATION               DETAILS…

AIM:          (A) Create the geometries from P1 to P8 using all the coordinates system methods. And we need to use line tool, and find the missing dimensions.         (B) Civil related problems- Draw the profile and the trusses using any coordinate system methods. The dimensions…

  Aim: To sketch a G+1 floor residential plan according to vastu Shastra and to list down the names of structural drawings required to be provided to the site for construction. To assume the size of structural elements (Column, Beam, slab etc) and to calculate the loads from the members as per IS code.    Ground…

INTRODUCTION: Concrete mix design is the method of finding the precise proportion of cement, sand and aggregates for concrete toachieve the target strength in structures, therefore concrete mix design can be stated as concrete mix in terms ofcement: sand: aggregates. The design is done according to the requirements of…