YATCH
AIM:
To create the yatch model using by solidworks
OBJECTIVES:
1.To design and model the yatch
2.Assembel the yatch
3.Render the yatch
SOFTWARE USED:
1.Solid works 2019
2.Solid works visualize 2019
INTRODUCTION:
Yatch is a water craft for pleasure or sports. IN solid works the yatch going to show through 2d and 3d sketch.
PARTS TO BE MODEL:
1.Propeller
2.Radar
3.Hull
4.Superstructure
5.Front seat
6.Middle seat
7.Rear seat
8.Radar mast
PROPELLER: A propeller is a type of fan which transmits power by converting rotational motion into thrust. A pressure difference is produced between the forward and rear surface of the airfoil shaped blades.
Commands used: sketch, revolved bass, lofted boss, fillet , circular pattern.
cad image
render image
RADAR: Radar is used to detect other ships and land obstacles . IT produce microwaves around the water surface surrounding the ship. It shows the path way of yatch to reach the destination.
Commands used: sketch , offset entities, extruded boss ,fillet, extruded cut , mirror, split line.
cad image
render image
HULL:A hull is the water light body of a ship or boat the hull may open at the top it may be fully or partially covered with a deck . the hull is the main source of the yatch it use to setup all the model.
Commands used: Sketch, offset entities, convert entities, filled surface , extruded surface, trim surface, projective curve, loft surface, extruded boss, extruded cut, linear patter, shell, split body, delete face, fillet, chamfer,mirror.
cad image
render image
GARAGE DOOR: The garage door body was split from the hull and imported sperately for modeling.
Commands used: Extruded cut , shell, fillet, mirror.
cad image
Render image:
FRONT SEAT:Front seat was placed in front of the superstructure on the hull it was designed after importing deck surface.
COMMAND: Swept surface, extrude surface , trim surface, filled surface , knit surface , mirror , revolved boss, fillet.
cad image:
Render image:
MIDDLE SEAT: Middle seat was placed behind the superstructure back door . the middle seat was designed using solid modeling commands.
COMMANDS: Sketch , offset entities, extruded boss, chamfer , fillet , mirror, extruded cut.
cad image:
Render image:
REAR SEAT: Rear seat was placed over the garage door behind the superstructure . it was designed using solid modeling .
COMMANDS: Swept surface , trim surface, ruled surface, knit surface, extended surface, extruded surface , lofted surface, chamfer , fillet , revolved boss, extruded cut , mirror.
cad image:
Render image:
SUPERSTRUCTURE: Superstructure is an upward extension of an existing structure a baseline it is a tricky part in yatch . it project above the hull. The size a water crafts superstructure can have may implications in its performance . these structures can alter their structural . these structure can alter their structural rigidity , their displacements and stability.
COMMANDS: Sketch, offset entities, convert entities, filled surface , extruded surface, trim surface, projective curve, loft surface, extruded boss, extruded cut, linear patter, shell, split body, delete face, fillet, chamfer, mirror, thin surface, swpet boss , offset surface.
cad image:
Render image:
RADAR MAST: The radar mast supports the radar , antennas and satellite domes and lights . IT was designed after importing the top surface of the superstructure.
COMMANDS: Sketch , offset entities , extruded boss , fillet , revolved boss , swept boss , shell , dome , chamfer.
cad image:
Render imgae:
CAD IMAGE:
RENDER IMAGE:
PROJECT LINK:https://drive.google.com/open?id=1urFw_gUicr8r1rBJqzzIXPY5cqVnMvr1