WEEK 01 AM CH BIKE CHALLENGE

HI

In this email contains the week 01 challages american chopper bike parts are done by the software of soildwork 2019. the models are given below

G Drive URL:https://drive.google.com/drive/folders/1D5KtaKlSkiRzWhKsa-e3xFh8omG32sWU

• TRANSMISSION BELT
• KICK STAND
• FRONT FENDER &
• REAR FENDER

TRANSMISSION BELT

• Draw a 2d sketch
• Draw two circles
• Draw two straight lines
• Trim lines
• Thin Extrude
• Add Fillets

• Before start the sketch unhide the all plane(FP,TP&RP)
• Select the front plane for base sketch and draw the circle with respect to the orgin and the onther one circle drawn with some distances
• Make the relation to the first circle coincident with the orgin
• And draw the line using L cmd in between to the two circle both upper and lower area
• Make the relation to the first circle and line is tangent vice versa
• Trim the line those was not used like inner circle and extended lines.
• Now the give the dimension of the sketch the first circle diameter is 120 same like the second dia is 140
• Now the sketch is ready and to give the features in that go to features area.
• Click the \"Boss/Base > Extrude\">Direction : Blind>Change : to 88 mm>Direction : One-Direction
• Now the your sketch almmost ready and add some fillets
• Click the Features > Fillet/Round>Select the inner and outer edges>fillet radius is 1mm click OK.

KICK STAND

the following features:

• Draw a 2d sketch
• Extrude
• Extruded Cut
• Loft
• Dome
• Fillet

• Before start the sketch unhide the all plane(FP,TP&RP) and change the name right plane into mid plane
• Select the Front Plane and create a sketch by clicking on the 2D sketch icon
• click at the Ellipse icon.Click on the origin. The origin must be the middle of the ellipse.
• The dimension of the ellipse is L=40&H=18
• Click at the Sketch button in the upper right corner to close the 2D Sketch
• Select the MIDPLANE KICKSTAND and create a new sketch.
• click at the Spline icon.Draw a spline without any midpoints
• Select the end point of thespline and select the top point of the ellipse and make the relation of both coincident
• Now assign the dimension L=202&H=110 on first point of the ellipse.
• Select the Horizontal relation in the Spline menu bar at the left side.
• The endpoint of the spline is now fully horizontal.
• Create a new plane Go to: Insert > Reference Geometry > Plane with respect to the spline
• Draw an ellipse Go to: Tools > Sketch Entities > Ellipse
• The dimension of the elipse is L=30&H=12
• Select the upper point of the ellipse, hold down the Control key and select the Origin to make the relation as coincident
• Go to: Insert > Boss/Base > Loft or click on the Loft icon.select the two elipse as a main sketch and select the spline as a guide curve. and click ok
• create the both side \"DOME\" feature Go to: Insert > Feature > Dome or click on the Dome icon.
• the value of the dome is 13,5 mm and click ok.
• Select the MIDPLANE KICKSTAND and create another sketch
• click on the Centre Rectangle icon and the dimension are L=28&H=8
• Go to: Insert > Cut > Extrude or click at the Cut Extrude icon.
• Direction 1 : Mid Plane Change into: 100 mm.click OK.
• Same like that opposite side also.
• Select the Top Plane and create another sketch
• click on the Circle icon.clicking on the dimension button.Dia=9
• Now the give the fillet on inner area 2 and same like edge on .5mm
• click ok and save it.

FRONT FENDER

the following features:

• Draw a 2d sketch
• Revolved Surface
• Surface Trim
• Thicken
• Extruded Cut
• Fillet

• Before start the sketch unhide the all plane(FP,TP&RP) and change the name FP=VP,TP=CP&RP=MP
• Sketch the VERTICAL PLANE
• Draw a 3 Point Arc Go to Tools > Sketch Entities > 3 Point Arc or click on the 3 Point Arc icon.
• Make the endpoints of the arc parallel to each other
• Change the dimensions of the arc
• Create a Revolved Surface Go to: Insert > Surface > Revolve or click on the Revolved Surface icon. Select the horizontal centerline as the Axis of Revolution.
• Click OK.
• Select the MIDPLANE FRONT FENDER and create a sketch by clicking on the 2D Sketch icon.
• Draw the two lines.Draw two diagonal lines starting at the origin.
• Go to: Insert > Surface > Trim or click on the Trim icon. Select the new Sketch2 as the Trim tool. Select the Keep selections option. Select the purple piece to keep.
• Click OK.
• Create a Thicken Go to: Insert > Boss/Base > Thicken or click on the Thicken icon. Surface to thicken : Select the revolved surface. Thicken side : Thicken Side 1. Thickness : 6 mm.
• Click OK.
• Select the CENTERPLANE>create a new sketch
• Draw a vertical construction line starting at the origin. Draw a spline and add the dimensions. Mirror this spline about the vertical construction line in the middle of the sketch.
• Create an Extruded Cut Go to: Insert > Cut > Extrude. >Direction 1 : Through All. Ensure that the offset is directed toward the revolve.
• Same like opposite direction also
• Create a Surface Fillet Go to: Insert > Features > Fillet/Round or click on the Fillet icon. Click on the green surface as shown in the picture. Change the Radius into 6 mm.
  Click OK.

REAR FENDER

the following features:

• Draw a 2d sketch
• Revolved Surface
• Surface Trim
• Thicken
• Extruded Cut
• Fillet
• Shell
• Insert a Split line

• Before start the sketch unhide the all plane(FP,TP&RP) and change the name FP=VP,TP=CP&RP=MP
• Select the VERTICAL PLANE REAR FENDER and create another sketch by clicking on the 2D Sketch icon.
• Go to Tools > Sketch Entities > 3 Point Arc or click on the 3 Point Arc icon.
• Make the endpoints of the arc parallel to each other
• Change the dimensions of the arc
• Create a Revolved Surface Go to: Insert > Surface > Revolve or click on the Revolved Surface icon. Select the horizontal centerline as the Axis of Revolution.
• Click OK.
• Select the MIDPLANE FRONT FENDER and create a sketch by clicking on the 2D Sketch icon.
• Draw the two lines.Draw two diagonal lines starting at the origin.
• Go to: Insert > Surface > Trim or click on the Trim icon. Select the new Sketch2 as the Trim tool. Select the Keep selections option. Select the purple piece to keep.
• Click OK.
• Create a Thicken Go to: Insert > Boss/Base > Thicken or click on the Thicken icon. Surface to thicken : Select the revolved surface. Thicken side : Thicken Side 1. Thickness : 6 mm.
• Click OK.
• Select the CENTERPLANE REAR FENDER
• Draw a vertical construction line starting at the origin. Draw two circles and add the dimensions as Dia 530&1000
• Create an Extruded Cut Go to: Insert > Cut > Extrude Direction 1 : Trough All Ensure that the offset is directed toward the revolve. If not, click “Reverse direction”.
• Click OK.
• Create a Surface FilletGo to: Insert > Features > Fillet/Round or click on the Fillet icon. Click on the green surface as shown in the picture. Change the Radius to 4 mm.
• Click OK.
• Create a Shell on the green surface Select the green surface as shown in the picture. Go to: Insert > Features > Shell or click on the Shell icon. Change the Thickness to 4 mm.
• Click OK.
• Create a new plane parallel at the CENTERPLANE REAR FENDER
• Go to: Insert > Reference Geometry > Plane or click on the Plane icon. Select the CENTERPLANE REAR FENDER
• Change the Offset Distance to 400 mm. Ensure that the offset is directed above the plane. If not, click “Reverse direction”.
• Click OK.
• Setch newly created plane Draw a vertical construction line starting at the origin
• Select the Imported Sketch Click and drag over the sketch to select the flames.
• Create a Projected Sketch Go to: Insert > Curve > Split Line or click on the Split Line icon. Select Sketch 4 as Sketch to Project Select the blue surface as Faces to Split.
• Click OK.
• Change the color of the flames Select the surfaces of the flames as shown in the picture.>Click on the appearances button.>Click on the Face option. >Change the color to white.
• Click OK.